Kenwood TK-2217 Service Manual page 9

TK-2217
4-3. Operation
1. To switch the clone target/s to Clone mode, press and hold
the [<B] key while turning the transceiver power ON.
2. Wait for 2 seconds. "CLONE" appears on the LCD, followed
by "FRQTBL 1".
3. Select a channel table number using the [Selector] knob.
4. To switch the clone source to Clone mode, press and hold
the [<B] key while turning the transceiver power ON.
5. Wait for 2 seconds. "CLONE" appears on the LCD, followed
by "FRQTBL 1".
6. Select the same channel table number as the clone target/s.
7. Press the [S] key on the clone source to begin data
transmission. When the clone target starts to receive data,
the green LED will light and "CLONING" will appear on
the LCD. The source unit will display "MASTER".
8. When the clone source finishes sending data, a
"confirmation" tone will sound and "COMPLETE" will
appear on the LCD. If data transmission failed while cloning,
the target unit will produced an error tone and "CLONE
NG" will appear on the LCD.
9. If the cloning fails, no data will be available in the target
unit when it is returned to User mode.
10.When the cloning is successful, the target unit's "Scan"
and "Key lock" functions will return to their default values
(Scan = OFF, Key lock = OFF).
11.The source will remain in clone mode after cloning. The target
unit will return to user mode after a successful cloning.
Notes:
• The dealer can clone data to two or more transceivers by
repeating the above procedures.
• If the transceivers Clone Mode is configured as "Disabled",
the transceiver cannot enter Clone mode.
• The table shown below will cover the frequency tables used
for wireless cloning.
• Clone mode cannot be entered in battery low state.
• A unit cannot be a "Source Unit" if it is unprogrammed. If
the [S] key is pressed, an "error" tone will sound.
• Once a unit is set to be the Source, it cannot be a target
after the data has been transmitted. This protects the data
in the Source unit.
• MSK signaling is used in cloning.
• Electronic interface may cause a failure in data transfer
during Wireless Clone, such as when waveforms or
electromagnetics are being performed at the workbench.
• Clone mode can be used ONLY by the authorized service
personnel.
• The Clone mode setting must be configured as "Disable"
before being delivered to the end-user.
• To clone, replace the antenna from both the source
transceiver and the target transceiver with a dummy
load.
• The transmit output power is automatically set to Low
in Clone mode.
8
REALIGNMENT /
模式组合
4-3. 操作方法
1. 将子机切换到复制模式，接通(ON)对讲机电源开关的同时，
持续按[<B]键。
2. 等待 2 秒。LCD 上显示"CLONE" ，然后显示"FRQTBL 1" 。
3. 用[Selector]旋钮选择频率表号码。
4. 将主机切换到复制模式，打开对讲机电源(ON)的同时，持续
按[<B]键。
5. 等待2秒。 在 LCD上显示 "CLONE" ， 然后显示 "FRQTBL 1" 。
6. 选择与复制子机相同的频率表号码。
7. 按复制主机上的[S]键， 开始传输数据。 当复制子机开始接收
数据时，绿色 LED 将亮灯，并且"CLONING"显示在 LCD
上。主机将显示出"MASTER" 。
8. 当复制主机完成数据传送，将发出一个"确认"音，并且在
LCD上显示出 "COMPLETE" 。 如果复制中数据通讯失败， 子
机将发出错误音，而且在 LCD 上显示出"CLONE NG" 。
9. 如果复制失败，子机回到用户模式时会无可用数据。
10.当复制成功时，子机的"扫描"和"键锁定"功能将返回到
它们的初始值(扫描＝ OFF，键锁定＝ OFF)。
11.主机在复制后将停留在复制模式。复制成功后，子机将返回
到用户模式。
注∶
• 经销上可以把同样的数据反复地复制到两台或更多的对讲
机。
• 如果对讲机的复制模式被设定为 "禁用" ， 则对讲机不能进入
复制模式。
• 此表是使用于无线复制的频率表。
• 在电池低电压状态时，不能进入复制模式。
• 如果没有被编程，就不能成为"主机" 。如果[S]键被按，将
会发出"错误"音。
• 对讲机一旦被设定为主机，而且数据被传送之后，它就不能
成为子机。此功能是为了保护主机内的数据。
• MSK 信号用于复制。
• 电子干扰有可能导致无线复制时数据传送失败， 如在工作台
上受到电波或电磁的干扰。
• 复制模式只可以由授权的服务人员使用。
• 在向最终用户交货之前，复制模式必须设置为"禁用" 。
• 复制时，取下主对讲机和子对讲机的天线并装上假负载。
• 在复制模式，对讲机输出功率自动地被设定为低功率。