Table of Contents
Advertisement
Quick Links
GETTING STARTED GUIDE
NI PXIe-4136/4137
Single-Channel System Source Measure Unit (SMU)
Note
Before you begin, install and configure your chassis and controller.
This document explains how to install, configure, and test the NI PXIe-4136/4137
(NI 4136/4137). The NI 4136/4137 is a single-channel system source measure unit (SMU).
To access NI 4136/4137 documentation, navigate to Start»All Programs»National
Instruments»NI-DCPower»Documentation.
Caution
document. Product misuse can result in a hazard. You can compromise the safety
protection built into the product if the product is damaged in any way. If the product
is damaged, return it to NI for repair.
Contents
Electromagnetic Compatibility Guidelines...............................................................................2
Safety Guidelines for Hazardous Voltages............................................................................... 2
Verifying the System Requirements......................................................................................... 2
Unpacking the Kit..................................................................................................................... 3
Kit Contents.............................................................................................................................. 3
Other Equipment...............................................................................................................4
Preparing the Environment....................................................................................................... 4
Safety........................................................................................................................................ 5
Installing the Software.............................................................................................................. 5
System Safety Guidelines......................................................................................................... 5
Safety Guidelines for System Design and Implementation.............................................. 5
Safety Guidelines for System Operation.......................................................................... 7
Installing the NI 4136/4137...................................................................................................... 7
Configuring the NI 4136/4137 in MAX................................................................................. 10
Testing the Safety Interlock.................................................................................................... 10
Testing with an Application Development Environment................................................11
Testing with the NI-DCPower Soft Front Panel............................................................. 11
Programming the NI 4136/4137............................................................................................. 12
Troubleshooting...................................................................................................................... 12
What Should I Do if the NI 4136/4137 Doesn't Appear in MAX?.................................12
Why Is the ACCESS LED Off When the Chassis Is On?.............................................. 13
Where To Go Next.................................................................................................................. 14
Worldwide Support and Services............................................................................................14
Do not operate the NI 4136/4137 in a manner not specified in this
Advertisement
Table of Contents
Related Manuals for National Instruments PXIe-4136
Summary of Contents for National Instruments PXIe-4136
-
Page 1: Table Of Contents
Note Before you begin, install and configure your chassis and controller. This document explains how to install, configure, and test the NI PXIe-4136/4137 (NI 4136/4137). The NI 4136/4137 is a single-channel system source measure unit (SMU). To access NI 4136/4137 documentation, navigate to Start»All Programs»National Instruments»NI-DCPower»Documentation. -
Page 2: Electromagnetic Compatibility Guidelines
Refer to the product readme, which is available on the driver software media or online at ni.com/manuals, for more information about minimum system requirements, recommended system, and supported application development environments (ADEs). 2 | ni.com | NI PXIe-4136/4137 Getting Started Guide... -
Page 3: Unpacking The Kit
1. NI PXIe-4136/4137 System SMU Device 4. Driver Software DVD 2. Output Connector Assembly 5. NI PXIe-4136/4137 Getting Started Guide (this document) 3. Safety Interlock Input Connector 6. Maintain Forced-Air Cooling Note to Users NI PXIe-4136/4137 Getting Started Guide | © National Instruments | 3... -
Page 4: Other Equipment
IEC 60068-2-1 and IEC 60068-2-2.) 2,000 m (800 mbar) (at 25 °C ambient Maximum altitude temperature) Pollution Degree Indoor use only. Note Refer to the device specifications on ni.com/manuals for complete specifications. 4 | ni.com | NI PXIe-4136/4137 Getting Started Guide... -
Page 5: Safety
Double insulate all electrical connections that are accessible by an operator. Double insulation ensures protection if one layer of insulation fails. Refer to IEC 61010-1 for specific insulation requirements. NI PXIe-4136/4137 Getting Started Guide | © National Instruments | 5... - Page 6 Use two normally open switches wired in series so that a single switch failure does not compromise safety protections. • Isolate switches so the operator cannot trigger or bypass the switches without the use of a tool. 6 | ni.com | NI PXIe-4136/4137 Getting Started Guide...
-
Page 7: Safety Guidelines For System Operation
Remove the black plastic connectors from all the captive screws on the module front panel. Identify a supported slot in the chassis. The following figure shows the symbols that indicate the slot types. NI PXIe-4136/4137 Getting Started Guide | © National Instruments | 7... - Page 8 11. Cover all empty slots using filler panels or slot blockers to maximize cooling air flow. 8 | ni.com | NI PXIe-4136/4137 Getting Started Guide...
- Page 9 (0.295 in.) minimum and 10 mm (0.394 in.) absolute maximum. Acceptable AWG Range for safety interlock cable is 16-24. Use an insulation strip tool to expose cable of the appropriate length. NI PXIe-4136/4137 Getting Started Guide | © National Instruments | 9...
-
Page 10: Configuring The Ni 4136/4137 In Max
In order to ensure safe operation of the NI 4136/4137, periodically test the safety interlock for proper functionality. The recommended test interval is at least once per day of continuous usage. 10 | ni.com | NI PXIe-4136/4137 Getting Started Guide... -
Page 11: Testing With An Application Development Environment
Caution If the NI 4136/4137 fails the safety interlock test, discontinue use of the device and contact an authorized NI service representative to request a Return Material Authorization (RMA). NI PXIe-4136/4137 Getting Started Guide | © National Instruments | 11... -
Page 12: Programming The Ni 4136/4137
What Should I Do if the NI 4136/4137 Doesn't Appear in MAX? In the MAX configuration tree, click Devices and Interfaces. Expand the Chassis tree to see the list of installed devices, and press <F5> to refresh the list. 12 | ni.com | NI PXIe-4136/4137 Getting Started Guide... -
Page 13: Why Is The Access Led Off When The Chassis Is On
Select Start»Control Panel»System»Hardware»Device Manager. If you are using a PXI controller, verify that a National Instruments entry appears in the system device list. Reinstall NI-DCPower and the device if error conditions appear in the list. If you are using an MXI controller, right-click PCI-to-PCI Bridge, and select Properties from the shortcut menu to verify that the bridge is enabled. -
Page 14: Where To Go Next
*This item is also installed with the driver software. Worldwide Support and Services The National Instruments website is your complete resource for technical support. At ni.com/ support, you have access to everything from troubleshooting and application development self-help resources to email and phone assistance from NI Application Engineers. - Page 15 National Instruments corporate headquarters is located at 11500 North Mopac Expressway, Austin, Texas, 78759-3504. National Instruments also has offices located around the world. For telephone support in the United States, create your service request at ni.com/support...
- Page 16 NI product. Refer to the Export Compliance Information at ni.com/legal/export-compliance the National Instruments global trade compliance policy and how to obtain relevant HTS codes, ECCNs, and other import/export data. NI MAKES NO EXPRESS OR IMPLIED WARRANTIES AS TO THE ACCURACY OF THE INFORMATION CONTAINED HEREIN AND SHALL NOT BE LIABLE FOR ANY ERRORS.
Need help?
Do you have a question about the PXIe-4136 and is the answer not in the manual?
Questions and answers