Table of Contents
Advertisement
GETTING STARTED GUIDE
PXIe-4147
PXIe, 4-channel ±8 V, 3 A PXI Source Measure Unit
This document explains how to install, configure, and test the PXIe-4147. The PXIe-4147
ships with NI-DCPower driver software, which you can use to program the module.
Note
Before you begin, install and configure your chassis and controller.
Contents
Verifying the System Requirements..........................................................................................1
Unpacking the Kit..................................................................................................................... 1
Other Equipment....................................................................................................................... 2
Preparing the Environment....................................................................................................... 3
Installing the Software.............................................................................................................. 4
Installing the PXIe-4147........................................................................................................... 4
PXIe-4147 Pinout and LEDs.....................................................................................................6
Configuring the PXIe-4147 in MAX........................................................................................ 8
Self-Calibrating the PXIe-4147................................................................................................ 9
Programming the PXIe-4147.................................................................................................. 10
Troubleshooting...................................................................................................................... 12
What Should I Do if the PXIe-4147 Doesn't Appear in MAX?......................................12
Why Is the ACCESS LED Off When the Chassis Is On?...............................................13
What Should I Do if the PXIe-4147 Fails the Self-Test?................................................13
Where To Go Next.................................................................................................................. 14
Worldwide Support and Services............................................................................................ 14
Verifying the System Requirements
To use the NI-DCPower instrument driver, your system must meet certain requirements.
Refer to the product readme, which is available on the driver software media or online at
ni.com/manuals, for more information about minimum system requirements, recommended
system, and supported application development environments (ADEs).
Unpacking the Kit
Refer to the following figure to identify the contents of the PXIe-4147 kit.
Advertisement
Table of Contents
Related Manuals for National Instruments PXIe-4147
Summary of Contents for National Instruments PXIe-4147
-
Page 1: Table Of Contents
GETTING STARTED GUIDE PXIe-4147 PXIe, 4-channel ±8 V, 3 A PXI Source Measure Unit This document explains how to install, configure, and test the PXIe-4147. The PXIe-4147 ships with NI-DCPower driver software, which you can use to program the module. Note Before you begin, install and configure your chassis and controller. -
Page 2: Other Equipment
Store the module in the antistatic package when the module is not in use. Other Equipment There are several required items not included in your PXIe-4147 kit that you need to operate the PXIe-4147. Your application may require additional items not included in your kit to install or operate your PXIe-4147. -
Page 3: Preparing The Environment
Screw Terminal Connector Kit for PXIe-414x SMUs (NI part number 781974-01) Visit ni.com for more information about these additional items. Preparing the Environment Ensure that the environment you are using the PXIe-4147 in meets the following specifications: Temperature and Humidity Temperature Operating 0 °C to 55 °C Storage -40 °C to 71 °C... -
Page 4: Installing The Software
To prevent damage to the PXIe-4147 caused by ESD or contamination, handle the module using the edges or the metal bracket. The PXIe-4147 is a single-slot module with one backplane connector. The module may be installed into any PXI Express-compatible slot. - Page 5 5. PXI Express Peripheral Slot 3. PXI Express Hybrid Peripheral Slot PXIe-4147 modules can be placed in PXI Express peripheral slots, PXI Express hybrid peripheral slots, or PXI Express system timing slots. Touch any metal part of the chassis to discharge static electricity.
-
Page 6: Pxie-4147 Pinout And Leds
Why Is the ACCESS LED Off When the Chassis Is On? on page 13 PXIe-4147 Pinout and LEDs PXIe-4147 4-CH Precision SMU ACCESS VOLTAGE OUTPUT ALL CHANNEL SIGNALS ±8 V , 3 A MAX MAX to GUARD HI S LO S GUARD 6 | ni.com | PXIe-4147 Getting Started Guide... - Page 7 CH 1 Guard Pin 19 CH 1 Output LO Pin 20 CH 2 Output HI Pin 21 CH 2 Guard Pin 22 CH 2 Output LO Pin 23 CH 3 Output HI PXIe-4147 Getting Started Guide | © National Instruments | 7...
-
Page 8: Configuring The Pxie-4147 In Max
Launch MAX. In the configuration tree, expand Devices and Interfaces to see the list of installed NI hardware. Installed modules appear under the name of their associated chassis. Expand your Chassis tree item. 8 | ni.com | PXIe-4147 Getting Started Guide... -
Page 9: Self-Calibrating The Pxie-4147
• After first installing the PXIe-4147 in a chassis • After any module that is in the same chassis as the PXIe-4147 is installed, uninstalled, or moved • When the PXIe-4147 is in an environment where the ambient temperature varies or the PXIe-4147 temperature has drifted more than ±5 °C from the temperature at the last self-... -
Page 10: Programming The Pxie-4147
Programming the PXIe-4147 You can generate signals interactively using InstrumentStudio or you can use the NI-DCPower instrument driver to program your device in the supported ADE of your choice. 10 | ni.com | PXIe-4147 Getting Started Guide... - Page 11 • From Measurement & Automation Explorer (MAX), select a device and then click Test Panels..This launches InstrumentStudio and runs a soft front panel for the device you selected. PXIe-4147 Getting Started Guide | © National Instruments | 11...
-
Page 12: Troubleshooting
Troubleshooting If an issue persists after you complete a troubleshooting procedure, contact NI technical support or visit ni.com/support. What Should I Do if the PXIe-4147 Doesn't Appear in MAX? In the MAX configuration tree, expand Devices and Interfaces. Expand the Chassis tree to see the list of installed hardware, and press <F5> to refresh the list. -
Page 13: Why Is The Access Led Off When The Chassis Is On
LED. Notice Apply external signals only while the PXIe-4147 is powered on. Applying external signals while the module is powered off may cause damage. Disconnect any signals from the module front panels. -
Page 14: Where To Go Next
Launch MAX. • Failed self-test Perform self-calibration, then perform the self-test again. The PXIe-4147 must be calibrated to pass the self-test. • Failed self-calibration Perform self-calibration again. Power off the chassis. Reinstall the failed module in a different slot. Power on the chassis. - Page 15 NI. NI corporate headquarters is located at 11500 North Mopac Expressway, Austin, Texas, 78759-3504, USA. For up-to-date contact information for your location, visit ni.com/contact. PXIe-4147 Getting Started Guide | © National Instruments | 15...
- Page 16 NI trademarks. Other product and company names mentioned herein are trademarks or trade names of their respective companies. For patents covering NI products/technology, refer to the appropriate location: Help»Patents in your software, the file on your media, or the National Instruments Patent Notice at . You can find patents.txt ni.com/patents...
Need help?
Do you have a question about the PXIe-4147 and is the answer not in the manual?
Questions and answers