Siemens SIMATIC NET RUGGEDCOM MX5000 Installation Manual
  1. Manuals
  2. Brands
  3. Siemens Manuals
  4. Multi-service Platforms
  5. SIMATIC NET RUGGEDCOM MX5000
  6. Installation manual
Siemens SIMATIC NET RUGGEDCOM MX5000 Installation Manual

Siemens SIMATIC NET RUGGEDCOM MX5000 Installation Manual

Hide thumbs Also See for SIMATIC NET RUGGEDCOM MX5000:
Table of Contents

Advertisement

Quick Links

Download this manual
Installation Manual
SIMATIC NET
Rugged Multi Service Platforms
RUGGEDCOM MX5000
Edition
01/2021
https://www.siemens.com

Advertisement

Table of Contents
loading

Related Manuals for Siemens SIMATIC NET RUGGEDCOM MX5000

Summary of Contents for Siemens SIMATIC NET RUGGEDCOM MX5000

  • Page 1 Installation Manual SIMATIC NET Rugged Multi Service Platforms RUGGEDCOM MX5000 Edition 01/2021 https://www.siemens.com...
  • Page 2 Preface Introduction Installing the Device SIMATIC NET Device Management Rugged Multi Service Platforms RUGGEDCOM MX5000 Modules Technical Specifications Installation Manual Certification 01/2021 C79000-G8976-1059-13...
  • Page 3 Note the following: WARNING Siemens products may only be used for the applications described in the catalog and in the relevant technical documentation. If products and components from other manufacturers are used, these must be recommended or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and maintenance are required to ensure that the products operate safely and without any problems.

  • Page 4: Table Of Contents

    Accessing Documentation ....................... v Registered Trademarks ......................v Warranty ..........................vi Training ..........................vi Customer Support ........................vi Contacting Siemens ....................... vii Introduction ........................... 1 Feature Highlights ....................1 Description ......................2 Required Tools and Materials ................. 4 Decommissioning and Disposal ................4 Cabling Recommendations ..................
  • Page 5 Table of Contents Installing/Removing Line Modules ................ 28 Installing/Removing Power Supply Modules ............30 Technical Specifications ...................... 35 Power Supply Specifications ................35 Failsafe Relay Specifications ................35 Operating Environment ..................35 Mechanical Specifications ..................36 Dimension Drawings ................... 36 Certification .........................

  • Page 6: Preface

    . To request or inquire about a user document, contact Siemens Customer Support. Registered Trademarks RUGGEDCOM ™ and ROS™ are trademarks of Siemens AG. Linux® is the registered trademark of Linus Torvalds in the United States and other countries. The registered trademark Linux® is used pursuant to a sublicense from LMI, the exclusive licensee of Linus Torvalds, owner of the mark on a world-wide basis.

  • Page 7: Warranty

    Preface Warranty Warranty Siemens warrants this product for a period of five (5) years from the date of purchase, conditional upon the return to factory for maintenance during the warranty term. This product contains no user-serviceable parts. Attempted service by unauthorized personnel shall render all warranties null and void.

  • Page 8: Contacting Siemens

    Call a local hotline center to submit a Support Request (SR). To locate a local hotline center, visit https://w3.siemens.com/aspa_app/?lang=en. Mobile App Install the Industry Online Support app by Siemens AG on any Android, Apple iOS or Windows mobile device and be able to: •...
  • Page 9 Preface Contacting Siemens viii RUGGEDCOM MX5000 Installation Manual, 01/2021, C79000-G8976-1059-13...

  • Page 10: Introduction

    Introduction The RUGGEDCOM MX5000 is a MIL-STD, high-port density routing and switching platform, designed to operate in the most demanding environments.The RUGGEDCOM MX5000 can withstand high levels of electromagnetic interference, radio frequency interference, and a wide temperature range of -40 to 85 °C (-40 to 185 °F).

  • Page 11: Description

    Introduction 1.2 Description • Terminal blocks for reliable maintenance-free connections • CSA/UL 62368-1 safety approved to 85 °C (185 °F) Description The RUGGEDCOM MX5000 features various ports, controls and indicator LEDs on individual modules and the front panel for connecting, configuring and troubleshooting the device.
  • Page 12 Introduction 1.2 Description Power Supply Module Indicator LEDs Alarm Indicator LEDs Utility USB Port Management Ethernet Port Lamp Test/Alarm Cut-Off (LT/ACO) Button RS232 Serial Console Port (DB9) Figure 1.2 Front Panel Figure 1.3 Front Panel – Fan Controller Option Power Supply Module Indicator Indicate the status of the power modules.

  • Page 13: Required Tools And Materials

    Introduction 1.3 Required Tools and Materials Utility USB Port Use the USB port to upgrade the RUGGEDCOM RUGGEDCOM MX5000 software or install files, such as configuration files and feature key files. For more information, refer to the RUGGEDCOM ROX Configuration Manual for the RUGGEDCOM MX5000. Compact Flash Card Port Houses the CompactFlash (CF) card that contains active and backup installations of RUGGEDCOM RUGGEDCOM MX5000, along with...

  • Page 14: Cabling Recommendations

    Siemens also does not recommend using copper Ethernet ports to interface with devices in the field across distances that could produce high levels of ground potential rise (i.e. greater than 2500 V), during line-to-ground fault conditions.

  • Page 15: 1.5.3 Supported Fiber Optic Cables

    Introduction 1.5.3 Supported Fiber Optic Cables • Data cable lengths should be as short as possible, preferably 3 m (10 ft) in length. Copper data cables should not be used for inter-building communications. • Power and data cables should not be run in parallel for long distances, and should be installed in separate conduits.

  • Page 16: Installing The Device

    This product contains no user-serviceable parts. Attempted service by unauthorized personnel shall render all warranties null and void. Changes or modifications not expressly approved by Siemens AG could invalidate specifications, test results, and agency approvals, and void the user's authority to operate the equipment.

  • Page 17: General Procedure

    Visually inspect each item in the package for any physical damage. Verify all items are included. IMPORTANT If any item is missing or damaged, contact Siemens for assistance. Mounting the Device The RUGGEDCOM MX5000 is designed for maximum mounting and display flexibility.

  • Page 18: Mounting The Device To A Rack

    Installing the Device 2.3.1 Mounting the Device to a Rack Forced airflow is not required. However, any increase in airflow will result in a reduction of ambient temperature and improve the long-term reliability of all equipment mounted in the rack space. Note For detailed dimensions of the device with mounting hardware installed, refer to "Dimension Drawings (Page...
  • Page 19 Installing the Device 2.3.1 Mounting the Device to a Rack To secure the device to a standard 48 cm (19 in) rack, do the following: Make sure the adapters are installed on the correct side of the chassis. • To make the modules and ports accessible, install the adapters at the rear of the chassis •...

  • Page 20: Mounting The Device To A Panel

    Installing the Device 2.3.2 Mounting the Device to a Panel Insert the device into the rack. Note Since heat within the device is channeled to the enclosure, it is recommended that 1 rack-unit of space, or 44 mm (1.75 in), be kept empty above the device. This allows a small amount of convectional airflow.
  • Page 21 Installing the Device 2.3.2 Mounting the Device to a Panel To mount the device to a panel, do the following: Place the device against the panel and align the adapters with the mounting holes. Screw RUGGEDCOM MX5000 Installation Manual, 01/2021, C79000-G8976-1059-13...

  • Page 22: Installing The Chassis Ground Connection

    Installing the Device 2.4 Installing the Chassis Ground Connection Adapter Figure 2.2 Panel Mounting Install the supplied screws to secure the adapters to the panel. Make sure the screws are torqued to 2 ± 0.1 N·m (18 ± 1 lbf-in) Installing the Chassis Ground Connection If the ground terminal on the power supply module(s) is not connected to safety Earth, a connection must be provided from the chassis ground terminal on the RUGGEDCOM MX5000 chassis.

  • Page 23: Grounding The Device

    Installing the Device 2.5 Grounding the Device Secure the grounding cable and external tooth lock washer to the RUGGEDCOM MX5000 with one pan head screw. Torque the screw to 3.4 N·m (30 lbf·in). Note The other end of the grounding cable will be connected to the inside of the enclosure in later steps.

  • Page 24: Connecting Power

    Installing the Device 2.7 Connecting Power   Function Normally Closed Common Ground Normally Open Normally Open Common (Ground) Normally Closed Figure 2.5 Failsafe Alarm Relay Wiring Connecting Power The RUGGEDCOM MX5000 supports dual redundant AC and/or DC power modules that can be installed in any combination. The RUGGEDCOM MX5000 is equipped with a screw-type terminal block, which provides power to both power modules.

  • Page 25: 2.7.1 Connecting Ac Power

    Installing the Device 2.7.1 Connecting AC Power • For 125/230 VAC rated equipment, an appropriately rated AC circuit breaker must be installed. • For 125/250 VDC rated equipment, an appropriately rated DC circuit breaker must be installed. • It is recommended to provide a separate circuit breaker for each power module module.

  • Page 26: 2.7.2 Connecting Dc Power

    Installing the Device 2.7.2 Connecting DC Power Connect the positive wire from the power source to the live terminal on the terminal block. Live Terminal Ground Terminal Neutral Terminal Figure 2.6 AC Terminal Block Wiring Connect the negative wire from the power source to the neutral terminal on the terminal block.
  • Page 27 Installing the Device 2.7.2 Connecting DC Power Connect the positive wire from the power source to the positive terminal on the terminal block. Live Terminal Ground Terminal Neutral Terminal Figure 2.7 DC Terminal Block Wiring Connect the negative wire from the power source to the neutral terminal on the terminal block.

  • Page 28: Device Management

    Device Management This section describes how to connect to and manage the device. Connecting to the Device The following describes the various methods for accessing the RUGGEDCOM MX5000 console and Web interfaces on the device. For more detailed instructions, refer to the RUGGEDCOM ROX Configuration Manual for the RUGGEDCOM MX5000.

  • Page 29: Configuring The Device

    Device Management 3.2 Configuring the Device The management port is a 10/100Base-TX copper Ethernet port with an RJ45 connector. The following is the pin-out for the management port:   Name Description Transmit Data+ Transmit Data- Receive Data+ Reserved (Do Not Connect) Figure 3.2 RJ45 Management Port Reserved (Do Not Connect)
  • Page 30 The following will void the warranty and potentially result in configuration data corruption/loss: • Using a CF card not approved by Siemens for use with this device • Removing the CF card in any scenario other than those described in this section...
  • Page 31 Device Management 3.3 Accessing the CompactFlash Card Removing the CF card To remove the CF card from the device, do the following: Make sure the device is powered down. Remove the CF card access panel. Ejector Button CompactFlash Card Access Panel Figure 3.4 Removing the CF Card Press the ejector button to the left of the CF card and then pull the card out.

  • Page 32: Modules

    Modules The RUGGEDCOM MX5000 features slots for up to two power modules and eight line modules, which can be used to expand and customize the capabilities of the device to suit specific applications. A variety of modules are available, each featuring a specific type of communication port: copper Ethernet, fiber optic Ethernet, SFP or serial.

  • Page 33: Available Modules

    Available Modules The following is a list of all power and line modules available for use in the RUGGEDCOM MX5000. For more information about individual modules, refer to the RUGGEDCOM MX5000 Modules Catalog [https://support.industry.siemens.com/cs/ca/ en/view/109748778]. Power Supply Modules RUGGEDCOM MX5000PN PS MHIF...
  • Page 34 Modules 4.1 Available Modules Wavelength: 850 nm Ports: 4 Port Type: LC Distance: 500 m (1640 RUGGEDCOM MX5000PN LM M4FG03 Specifications Article Numbers Mode: Single 6GK6050-0ML20-0CR1 Speed: 1000 Mbps Interface: LX Wavelength: 1310 nm Ports: 4 Port Type: LC Distance: 10 km (6 mi) RUGGEDCOM MX5000PN LM M4FG05 Specifications Article Numbers...
  • Page 35 Modules 4.1 Available Modules Port Type: LC Distance: 2 km (1.2 mi) RUGGEDCOM MX5000PN LM M4FX11 Specifications Article Numbers Mode: MM 6GK6050-0ML20-0BH1 Speed: 100 Mbps Interface: FX Wavelength: 1300 nm Ports: 4 Port Type: LC Distance: 2 km (1.2 mi) Serial Modules RUGGEDCOM MX5000PN LM MS01 Specifications Article Numbers...
  • Page 36 Modules 4.1 Available Modules RUGGEDCOM MX5000PN LM MSM36 Specifications Article Numbers Mode: SM 6GK6050-0ML40-0RA1 Speed: 1000 Mbps Interface: LX Wavelength: 1310 nm Ports: 2 Port Type: LC Distance: 10 km (6 mi) RUGGEDCOM MX5000PN MSM61 Specifications Article Numbers Network Layer: Layer 3 6GK6050-0ML40-0VA1 RUGGEDCOM MX5000PN MSM69 Specifications...

  • Page 37: Installing/Removing Line Modules

    Modules 4.2 Installing/Removing Line Modules RUGGEDCOM MX5000PN LM Blank Specifications Article Numbers — 6GK6050-0ML20-0AA1 Installing/Removing Line Modules Upon installing a new line module in the device, all features associated with the module are available in RUGGEDCOM MX5000 . For more information, refer to the RUGGEDCOM ROX Configuration Manual for the RUGGEDCOM MX5000.
  • Page 38 Modules 4.2 Installing/Removing Line Modules NOTICE Contamination hazard – risk of equipment damage Prevent the ingress of water, dirts and other debris that may lead to premature equipment failure. Always make sure slots are not left empty and open ports are protected with plugs or covers.

  • Page 39: Installing/Removing Power Supply Modules

    Modules 4.3 Installing/Removing Power Supply Modules Installing a Line Module To install a line module, do the following: For Control and switch modules only, make sure power to the device has been disconnected and wait approximately two minutes for any remaining energy to dissipate.
  • Page 40 Modules 4.3 Installing/Removing Power Supply Modules Power Supply Module (PS1) Power Supply Module (PS2) Figure 4.5 Power Supply Modules NOTICE Contamination hazard – risk of equipment damage Prevent the ingress of water, dirts and other debris that may lead to premature equipment failure. Always make sure slots are not left empty. Note Power modules are hot swappable.
  • Page 41 Modules 4.3 Installing/Removing Power Supply Modules Removing a Power Supply Module To remove a power module, do the following: Loosen the screws that secure the module to the chassis until the module can be removed. Screws Power Supply Chassis Figure 4.6 Removing a Power Supply Slide the module out of the chassis.
  • Page 42 Modules 4.3 Installing/Removing Power Supply Modules Insert the module into the empty slot. Screws Power Supply Chassis Figure 4.7 Installing a Power Supply Module Hand-tighten the screws to secure the power module to the chassis. Turn on power to the device and confirm the module is receiving and supplying power.
  • Page 43 Modules 4.3 Installing/Removing Power Supply Modules RUGGEDCOM MX5000 Installation Manual, 01/2021, C79000-G8976-1059-13...

  • Page 44: Technical Specifications

    Technical Specifications This section provides important technical specifications related to the device and available modules. Power Supply Specifications Power Input Range Internal Max. Power Supply Type Fuse Rating Consumption HI (125/250 VDC) 88 VDC 300 VDC 6.3 A, 250 V(T) 110 W HI (110/230 VAC) 85 VAC...

  • Page 45: Mechanical Specifications

    Technical Specifications 5.4 Mechanical Specifications Operating temperature may vary based on the limitations of installed SFPs. Refer to the RUGGEDCOM SFP Transceivers Catalog for SFP temperature ratings. Non-condensing. Mechanical Specifications Weight 14-16 kg (30-35 lbs) Ingress Protection IP40 Chassis Material Aluminum Dimension Drawings Note All dimensions are in millimeters, unless otherwise stated.
  • Page 46 Technical Specifications 5.5 Dimension Drawings 177.8 175.3 16.0 221.5 12.7 311.9 101.6 16.0 117.6 133.4 31.8 Figure 5.1 Overall Dimensions RUGGEDCOM MX5000 Installation Manual, 01/2021, C79000-G8976-1059-13...
  • Page 47 Technical Specifications 5.5 Dimension Drawings RUGGEDCOM MX5000 Installation Manual, 01/2021, C79000-G8976-1059-13...

  • Page 48: Certification

    UL 62368-1 Information Technology Equipment – Safety – Part 1: General Requirements) 6.1.2 European Commission (EC) This device is declared by Siemens AG to comply with essential requirements and other relevant provisions of the following EC directives: • EN 62368-1 Information Technology Equipment –...

  • Page 49: 6.1.3 Fda/Cdrh

    Products with Respect to the Restriction of Hazardous Substances The device is marked with a CE marking and can be used throughout the European community. A copy of the CE Declaration of Conformity is available from Siemens AG. For contact information, refer to "Contacting Siemens (Page vii)".

  • Page 50: Iso

    Quality management systems – Requirements 6.1.7 RoHS This device is declared by Siemens AG to meet the requirements of the following RoHS (Restriction of Hazardous Substances) directives for the restricted use of certain hazardous substances in electrical and electronic equipment: •...

  • Page 51: Emc And Environmental Type Tests

    Certification 6.3 EMC and Environmental Type Tests EMC and Environmental Type Tests The RUGGEDCOM MX5000 has passed the following EMC and environmental tests. IEC 61850-3 EMC Type Tests Test Description Test Levels Severity Levels IEC 61000-4-2 Enclosure Contact +/- 8 kV Enclosure Air +/- 15 kV IEC 61000-4-3...
  • Page 52 DC Power ports 5 kV   AC Power ports 5 kV   Siemens-specified severity levels IEEE 1613 EMC Type Tests Note The RUGGEDCOM MX5000 meets Class 2 requirements for an all-fiber configuration and Class 1 requirements for copper ports. Description...
  • Page 53 Certification 6.3 EMC and Environmental Type Tests Test Description Test Levels IEC 60255-21-2 Shock 30 g @ 11 mS RUGGEDCOM MX5000 Installation Manual, 01/2021, C79000-G8976-1059-13...
  • Page 54 Further Information Siemens RUGGEDCOM https://www.siemens.com/ruggedcom Industry Online Support (service and support) https://support.industry.siemens.com Industry Mall https://mall.industry.siemens.com Siemens AG Digital Industry Process Automation Postfach 48 48 90026 NÜRNBERG GERMANY...

Table of Contents