Toro TXL 2000 Operator's Manual
Brush cutter tool carrier
Hide thumbs
Also See for TXL 2000:
- Operator's manual (60 pages) ,
- Installation instructions (4 pages) ,
- Operator's manual (8 pages)
Related Manuals for Toro TXL 2000
Summary of Contents for Toro TXL 2000
- Page 1 Form No. 3429-947 Rev B Brush Cutter TXL 2000 Tool Carrier Model No. 22534—Serial No. 318000001 and Up *3429-947* B Register at www.Toro.com. Original Instructions (EN)
-
Page 2: Table Of Contents
This brush cutter attachment is intended to be used 1. Safety-alert symbol on a Toro tool carrier. It is designed primarily to level brush, tall weeds, saplings, and small trees and heavy This manual uses 2 words to highlight information. -
Page 3: Safety
Safety • Establish your own procedures and rules for operating on slopes. These procedures must include surveying the site to determine which General Safety slopes are safe for machine operation. Always use common sense and good judgment when This product is capable of amputating hands and performing this survey. -
Page 4: Maintenance And Storage Safety
Maintenance and Storage Safety and Instructional Safety Decals • Check fasteners at frequent intervals for proper Safety decals and instructions are tightness to ensure that the equipment is in safe easily visible to the operator and are operating condition. located near any area of potential danger. -
Page 5: Product Overview
To ensure optimum performance and continued safety result. certification of the machine, use only genuine Toro replacement parts and accessories. Replacement • Ensure that all hydraulic-fluid hoses parts and accessories made by other manufacturers... -
Page 6: Transport Position
Transport Position CAUTION Hydraulic couplers, hydraulic lines/valves, When transporting an attachment, keep the and hydraulic fluid may be hot. If you contact attachment as close to the ground as possible, no hot components, you may be burned. more than 15 cm (6 inches) above the ground, and keep the loader arms retracted. -
Page 7: Operating Tips
Operating Tips • Do not cut material larger than 7.6 cm (3 inches) in diameter. • To reverse the direction that the blades rotate, reverse the flow of hydraulics. • Engage the hydraulics with the throttle at L . When the blades rotate smoothly, increase the throttle to H IGH IDLE Important:... -
Page 8: Maintenance
Maintenance Determine the left and right sides of the machine from the normal operating position. CAUTION If you leave the key in the switch, someone could accidently start the engine and seriously injure you or other bystanders. Remove the key from the switch before you perform any maintenance. Recommended Maintenance Schedule(s) Maintenance Service Maintenance Procedure... -
Page 9: Checking The Planetary Fluid Level
Checking the Planetary Servicing the Cutting Fluid Level Blades Service Interval: Before each use or daily Blade Safety Fluid Type: 80W-90 Gear Oil, API-GL-5 approved A worn or damaged blade can break, and a piece Capacity: 0.41 L (14 fl oz) of the blade could be thrown at you or bystanders, Park the machine on a level surface, engage the resulting in serious personal injury or death. -
Page 10: Checking The Hydraulic Lines
Replacing the Blades Sharpening the Blades Replace the blades if they hit a solid object, are out of Remove the blades as described in Replacing the balance, or are bent. Blades (page 10) and use a file to sharpen the cutting edge at the end of the blade (Figure 11). -
Page 11: Storage
Storage Before long-term storage, wash the attachment with mild detergent and water to remove dirt and grime. Paint all scratched or bare metal surfaces. Note: Paint is available from your Authorized Service Dealer. Store the attachment in a clean, dry garage or storage area. - Page 12 While the exposure from Toro products may be negligible or well within the “no significant risk” range, out of an abundance of caution, Toro has elected to provide the Prop 65 warnings. Moreover, if Toro does not provide these warnings, it could be sued by the State of California or by private parties seeking to enforce Prop 65 and subject to substantial penalties.