SunSetter EasyShade Owner’s Manual & Installation Instruction
  1. Manuals
  2. Brands
  3. SunSetter Manuals
  4. Indoor Furnishing
  5. EASYSHADE
  6. Owner’s manual & installation instruction
SunSetter EasyShade Owner’s Manual & Installation Instruction

SunSetter EasyShade Owner’s Manual & Installation Instruction

Hide thumbs Also See for EasyShade:
Table of Contents

Advertisement

Quick Links

EASYSHADE
®
OWNER'S MANUAL
& INSTALLATION
INSTRUCTIONS
Do Not Discard,
Retain for Future Reference
Motorized
EasyShade®
WARNING:
FAILURE TO FOLLOW THESE
INSTRUCTIONS COULD RESULT
IN PERSONAL INJURY!
For Technical Support visit us at http://ownerscorner.sunsetter.com,
e-mail at contactus@sunsetter.com or call Toll Free 800-670-7071 • Fax 877-224-4944

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the EasyShade and is the answer not in the manual?

Questions and answers

Related Manuals for SunSetter EasyShade

Summary of Contents for SunSetter EasyShade

  • Page 1 & INSTALLATION INSTRUCTIONS Do Not Discard, Retain for Future Reference Motorized EasyShade® WARNING: FAILURE TO FOLLOW THESE INSTRUCTIONS COULD RESULT IN PERSONAL INJURY! For Technical Support visit us at http://ownerscorner.sunsetter.com, e-mail at contactus@sunsetter.com or call Toll Free 800-670-7071 • Fax 877-224-4944...
  • Page 2 Cable Brackets must be clear of obstructions. Multi Channel Remote Transmitter Guiding included with Wall Cable Post and spare CR2430 battery. Cable Bracket Note: The Fabric Panel width is 3” less than the EasyShade width (measured at the Aluminum Housing). Figure 1...

  • Page 3: Table Of Contents

    TABLE OF CONTENTS Motorized EasyShade Schematic View (Figure 1)..... . . Inside Front Cover Tools Needed ........... . 2 Parts Supplied (Figure 2) .

  • Page 4: Tools Needed

    Aluminum Housing and Cable Guide Brackets are mounted on the same vertical plane or surface. The Motorized EasyShade can be installed with the Mounting Brackets on a wall (Vertical Surface, see Figure 3) or on the underside of a structure (Horizontal Surface, see Figure 4). For all models, the two Mounting Brackets should be installed no more than 10”...

  • Page 5: Installation

    INTO BRACKETS  3. With your helper, lift the EasyShade Assembly up to the installed Mounting Brackets and insert the Top Groove of the EasyShade Assembly onto the Protruding Tab of the Mounting Brackets (see Figure 3 and 4). While maintaining upward pressure to keep the Top Groove of the EasyShade Assembly on the Tab of the Mounting Brackets, press the EasyShade Assembly toward the Mounting Bracket and be sure the Set Screw is aligned in the Recessed Portion of the EasyShade Assembly.
  • Page 6 Note: The Up and Down Stop Limits on the 8. Unroll the Vinyl Coated Guide Cables located at EasyShade Motor were set at the factory prior to each end of the Aluminum Housing Assembly, and shipment. The Down Stop Limit was set for a 36 allow them to hang flat against the Mounting Surface.
  • Page 7 EasyShade Housing). Mark a Horizontal 15. Place the lower end of one of the Vinyl Coated Line on the wall below each end of the EasyShade Cables through the hole in the Cable Guide Bracket Housing Assembly. See Figure 11.

  • Page 8: Operating The Easyshade

    Note: The Fabric Panel is preset to stop 36” from the Operating the EasyShade  Housing. This position can be changed to lower the 24. Test the operation of your EasyShade by using the Fabric Panel as much as 84” from the Housing. and DOWN buttons on the Remote Transmitter.

  • Page 9: Remote Transmitters Are Unique

    Your Motorized EasyShade is programmed to, and packaged with a specific Remote Transmitter and work together as a matched set. If you own more than one Motorized EasyShade, it is recommended to keep the Remote Transmitter that came with that Motorized EasyShade with that specific Motorized EasyShade. It helps to mark them.

  • Page 10: Troubleshooting - Installation

    Operation, on Page 9. c. If the Remote Transmitter got wet, it may need to be replaced. 7. In extreme cold conditions, verify the EasyShade Fabric Panel is not “frozen” inside the housing. a. A light tug on the Leading Bar in the bottom Pleat of the Fabric...

  • Page 11: Troubleshooting - Appearance

    1. Check the Aluminum Housing to ensure it is mounted level on the mounting pulls to one side when the surface. Motorized EasyShade is 2. It is necessary to have the Guiding Cables completely plumb, up and down. being closed.
  • Page 12 Operation (continued) Problem Solution My Motorized EasyShade Adjust the Up Limit on your EasyShade motor. See Appendix A, Adjusting the retracts but will not fully Up and Down Position Limits of the Motor. close into the Aluminum If the Fabric Panel has been replaced, new Up and Down Position Limits Housing.

  • Page 13: Troubleshooting - Operation

    EasyShade / Motor Does Not Respond to Remote Transmitter (Plug/Outlet has power and Remote Transmitter passes Self Test as described at bottom of this page.) EasyShade / Motor only runs while holding down the UP or DOWN button on the Remote. Solution: 1. Unplug Motor, 2.

  • Page 14: Appendix A - Adjusting The Up And Down Position Limits Of The Easyshade Motor

    See Figure 20. Position Figure 21 To Change the Up Stop Position: 1. Move the EasyShade to its current Up (see Figure 21) position and Button let it stop on its own. 2. Press and hold the (UP)

  • Page 15: Appendix B - Reset All Communications Between The Motor And Remote Transmitter

    5. Disconnect (at the Wall outlet) Power for 5 full seconds. 6. Connect Power (at the Wall outlet). Your EasyShade should move then stop on its own. 7. Press and hold the Programming button for ten seconds, watching for two separate jogs back DOWN and forth, several seconds apart.

  • Page 16: Appendix C - Programming Instructions - Multi Channel Remote Transmitter

    Channel Selector Indicator Light blinks. All 4 lights blinking means Channel 5 is selected. Button How to program the EasyShade to work with any Channel (see Figures 28, 29 & 30): One EasyShade can One Channel can Unwanted Channels can run on any Channel.

  • Page 17: 5-Year Limited Manufacturer's Warranty

    Subject to the terms and conditions set forth herein, prepaid, to SunSetter Products. SunSetter Products will furnish replacements for parts found by SunSetter Products to be defective in E. WHAT IS COVERED UNDER THIS design, manufacture or assembly, under each specific WARRANTY? component or product warranty as set forth below.
  • Page 18 Warranty. 2. It is the responsibility of the purchaser to securely fasten the EasyShade to studs, joists, headers or other structural members. Any failure or damage that results from the EasyShade falling from its installed position is not covered by this Warranty.
  • Page 19 A place for your notes:...
  • Page 20 A place for your notes: SunSetter Products, a Massachusetts Limited Partnership, 184 Charles Street, Malden, MA 02148 December 7, 2016 ES_M_Installation_2017...

Table of Contents