SunSetter EASYSHADE Owner's Manual & Installation Instructions
  1. Manuals
  2. Brands
  3. SunSetter Manuals
  4. Accessories
  5. EASYSHADE
  6. Owner's manual & installation instructions
SunSetter EASYSHADE Owner's Manual & Installation Instructions

SunSetter EASYSHADE Owner's Manual & Installation Instructions

Solar powered motorized
Hide thumbs Also See for EASYSHADE:
Table of Contents

Advertisement

Quick Links

E
S
ASY
HADE
®
OWNER'S MANUAL
& INSTALLATION
INSTRUCTIONS
Do Not Discard,
Retain for Future Reference
Solar
Powered
Motorized
EasyShade®
WARNING: FAILURE TO
FOLLOW THESE INSTRUCTIONS
COULD RESULT IN PERSONAL
INJURY!
For Technical Support visit us at www.sunsetter.com/ownerscorner
or call Toll Free 800-670-7071 • Fax 877-224-4944

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the EASYSHADE and is the answer not in the manual?

Questions and answers

Related Manuals for SunSetter EASYSHADE

Summary of Contents for SunSetter EASYSHADE

  • Page 1 & INSTALLATION INSTRUCTIONS Do Not Discard, Retain for Future Reference Solar Powered Motorized EasyShade® WARNING: FAILURE TO FOLLOW THESE INSTRUCTIONS COULD RESULT IN PERSONAL INJURY! For Technical Support visit us at www.sunsetter.com/ownerscorner or call Toll Free 800-670-7071 • Fax 877-224-4944...
  • Page 2 Aluminum Housing and Cable Brackets must be clear of obstructions. Vinyl Coated Guide Cable Multi-Channel Cable Remote Transmitter Bracket Note: The Solar Screen Fabric Panel width is 3” less than the EasyShade width (measured at the Aluminum Housing). Figure 1...

  • Page 3: Table Of Contents

    Factory Limit Settings The Up and Down stop limits on the EasyShade motor were set at the factory to stop 36” from the Housing. This will allow for completion of the installation process, where you will be instructed to adjust the Down Position Limit to a maximum 84”.

  • Page 4: Motorized Easyshade Schematic View

    Note: Prior to installing your Solar Powered Motorized EasyShade, please review Figure 1 (Solar Powered Motorized EasyShade Schematic View) then inspect to ensure that there are no obstructions on your wall surface, such as light fixtures or door handles that would interfere with or block the Fabric Panel as it is extended.

  • Page 5: Installation

    Brackets to create a flat mounting surface. 3 Use the 4mm Allen wrench (supplied) to secure Figure 4 Aluminum Mounting Bracket the Solar Panel to the EasyShade Housing by inserting Housing Mounting and tightening the provided Allen set screw under the for the...

  • Page 6: Horizontal Mounting

    Portion of the Mounting Note: The Up and Down Stop Limits on the EasyShade Bracket EasyShade Motor were set at the factory prior to Assembly Protruding shipment. The Down Stop Limit was set for a 36” Tab fits in EasyShade extension.
  • Page 7 Coated Cable, but you can not exceed 84” from the holes and secure in place with the #8 x 1-1/2 Flat Head bottom of the EasyShade Housing). Mark a Horizontal Screws. Line on the wall below each end of the EasyShade Housing Assembly. See Figure 12.
  • Page 8 20. Plug in the Motor secure in place with the supplied 5/64” Allen Wrench. Press and release the UP button on your Remote Repeat for the other side of the EasyShade. Transmitter to retract the Figure 18 See Figure 15.

  • Page 9: Operating The Easyshade

    Operating the EasyShade Unique Remote Transmitters 25. Test the operation of your EasyShade by using the Each Remote Transmitter and each Channel of and DOWN buttons on the Remote each Remote Transmitter (see Figure 20) has its Transmitter. own unique ID code. Each Motorized EasyShade...

  • Page 10: Faqs - Frequently Asked Questions

    10: Can the Solar Panel be left out in the winter? Yes. The Solar Powered Motorized EasyShade is an outdoor product that can withstand freezing and wintry conditions. Note: If the Fabric gets wet, it can freeze in the Housing and fail to unroll until the Fabric thaws 11: Can the Solar Panel get wet? Yes.

  • Page 11: Troubleshooting - Installation

    Appendix C for more information. 3. The Battery in the Solar Panel was originally shipped with enough charge to run the Motorized EasyShade. Expose the Solar Panel to sun for a full day to ensure enough charge exists in the Battery to run the Solar Powered Motorized EasyShade 4.

  • Page 12: Troubleshooting - Appearance

    The Solar Panel’s Battery charge is low. Exposure to sun will recharge the Solar three times before Panel’s Battery. EasyShade responds. EasyShade moves 1 inch at The Solar Panel’s Battery charge is low. Exposure to sun will recharge the Solar a time. Panel’s Battery.
  • Page 13 Operation (continued) Problem Solution My Motorized EasyShade Adjust the Up Limit on your EasyShade motor. See Appendix A, Adjusting the retracts but will not fully Up and Down Position Limits of the Motor. close into the Aluminum If the Solar Screen has been replaced, new Up and Down Position Limits Housing.

  • Page 14: Troubleshooting - Additional Motor Troubleshooting

    4. Test for normal operation. If GROUP A or B (above) does not fix the problem, then . . . Perform Steps 1 - 18 in Appendix B, or call SunSetter Technical Support at 800-670-7071. How to Self Test the 1.

  • Page 15: Appendix A - Adjusting The Up And Down Position Limits Of The Easyshade Motor

    See Figure 21. Position Figure 22 To Change the Up Stop Position: 1. Move the EasyShade to its current Up (see Figure 22) position and Button let it stop on its own. 2. Press and hold the (UP)

  • Page 16: Appendix B - Programming The Motor And Remote Transmitter

    5. Disconnect (at the Solar Panel connector) Power for 2 full seconds. 6. Connect Power (at the Solar Panel connector). Your EasyShade should move then stop on its own. 7. Press and hold the Programming button for ten seconds, watching for two separate jogs back DOWN and forth, several seconds apart.

  • Page 17: Appendix C - Programming Instructions - Multi-Channel Remote Transmitter

    Transmitter from an EasyShade is determined by whether or not the Remote Transmitter is known to the EasyShade. If a Remote Transmitter is not known by an EasyShade, it will be added to the EasyShade. If a Remote Transmitter is known by an EasyShade, it will be deleted from the EasyShade.

  • Page 18: 5-Year Limited Manufacturer's Warranty

    Subject to the terms and conditions set forth herein, prepaid, to SunSetter Products. SunSetter Products will furnish replacements for parts found by SunSetter Products to be defective in E. WHAT IS COVERED UNDER THIS design, manufacture or assembly, under each specific WARRANTY? component or product warranty as set forth below.
  • Page 19 Warranty. 2. It is the responsibility of the purchaser to securely fasten the EasyShade to studs, joists, headers or other structural members. Any failure or damage that results from the EasyShade falling from its installed position is not covered by this Warranty.
  • Page 20 Thank you for choosing SunSetter SunSetter Products, a Massachusetts Limited Partnership, 184 Charles Street, Malden, MA 02148 November 6, 2015 INS076-ES_Solar_Installation_2016...

This manual is also suitable for:

Easyshade

Table of Contents

Save PDF