Download
Share
Print this page
  1. Manuals
  2. Brands
  3. Dreamline Manuals
  4. Bathroom Fixtures
  5. Unidoor-X D58580 Series
  6. Installation instructions manual

Dreamline Unidoor-X D58580 Series Installation Instructions Manual

Frameless shower tub door
Hide thumbs

Advertisement

Quick Links

Download this manual
UNIDOOR-X TUB DOOR
T
IMPORTANT
DreamLine
reserves the right to alter, modify or redesign products at any time without prior notice.
®
For the latest up-to-date technical drawings, manuals, warranty information or additional details please refer
to your model's web page on DreamLine.com
Left-hand bracket installation shown
For more information about DreamLine
UNIDOOR-X Tub Door manual Ver 1 10/2016
D
I
UB
OOR
NSTALLATION
®
I
Shower Doors & Tub Doors please visit DreamLine.com
NSTRUCTIONS
©2017 DreamLine. All Rights Reserved
MODEL #s
D58580-##
##=finish
01- Chrome
04- Brushed Nickel
06- Oil Rubbed Bronze
09- Black Satin

Advertisement

loading
Need help?

Need help?

Do you have a question about the Unidoor-X D58580 Series and is the answer not in the manual?

Questions and answers

Related Manuals for Dreamline Unidoor-X D58580 Series

Summary of Contents for Dreamline Unidoor-X D58580 Series

  • Page 1 04- Brushed Nickel 06- Oil Rubbed Bronze 09- Black Satin Left-hand bracket installation shown For more information about DreamLine Shower Doors & Tub Doors please visit DreamLine.com ® ©2017 DreamLine. All Rights Reserved UNIDOOR-X Tub Door manual Ver 1 10/2016...
  • Page 2 This model is treated with DreamLine’s exclusive ClearMax Glass technology. This is a specially formulated coating that prevents the build up of soap and water spots. Install the surface with the ClearMax label towards the inside of the shower. Please note that depending on the model, the glass may be coated on either one or both surfaces.
  • Page 3 NOTE: This model is available as a right or left-hand bracket installation. The left-hand bracket installation is shown as an example throughout this manual. Left-hand bracket installation Right-hand bracket installation NOTE: Do Not attach the handle to the door glass until instructed to do so. Do Not attempt to lift the door glass with the handle as this may result in damage to the glass and/or serious personal injury.
  • Page 4 2. Please note that you should consult your local building codes with questions on installation compliance standards. Building and plumbing codes may vary by location, and DreamLine is not ®...
  • Page 5 Before discarding the carton, check for small hardware bags that may have fallen to the bottom of the box. If any parts are damaged or missing, please contact DreamLine for replacement. The shipping boxes may contain extra parts not used in ®...

  • Page 6: Parts List

    Detailed Diagram of shower door components inside rubber gasket The glass surface with the ClearMax™ label must be installed to face inside of the shower Parts List Door Glass Anti-Waterstrip (inline strike) Handle Countersunk screw ST4.2x40 Glass-to-Glass Hinge 2pcs U-channel 2 (44”, bottom profile) Bottom anti-water strip Hinge panel Glass (7”...

  • Page 7: Installation Steps

    Installation steps Draw a line on the threshold and on Cut the vertical u-channel to 55-7/16” for tub model the wall to represent the centerline of the height. U-channel. Make sure the line is parallel Cut the bottom u-channel** to the front edge of the threshold or tub to 7”...
  • Page 8 Mark the hole positions on Position the u-channels and the centerline on the wall and Hinge Panel Glass Bracket on tub deck through the holes in the centerlines to mark the the u-channels and the hinge holes for drilling. (Fig 3) panel glass bracket.
  • Page 9 Drill Ø5/16” holes in the wall Apply silicone to the back of the and install the wall anchors. Drill u-channels and the screw holes, Ø1/8” holes into the threshold or then install the u-channels and tub deck (or Ø5/16” holes and Hinge Panel Glass Bracket using anchors for a tile threshold).
  • Page 10 Install the hinge panel glass into Add the 0.5mm shims into the the u-channel. (Note the top and bottom u-channel. Apply silicone bottom of the hinge panel glass) into the u-channels. (Fig 7) Install the Hinge Panel Glass bracket gasket. (Fig 8) Hinge panel Glass bracket...
  • Page 11 Tighten the rubber tipped set screws on the Hinge Panel Glass Bracket (#36) to secure the glass. Do Not over-tighten! (Fig 9) Fig 9 NOTE: During installation of the Hinge Panel Glass (#32), it is strongly recommended that the silicone be allowed to fully cure before hanging the door glass. NOTE: Do Not attach the handle to the door glass until instructed to do so.
  • Page 12 NOTE: It is strongly advisable to allow the silicone to set on the hinge panel glass connection with the Leave the U-channel before hanging the door glass. shims in place beneath the door glass while the silicone cures, especially if an out-of-plumb wall condition is present (not to exceed 1/4”).
  • Page 13 Insert three to four 2” pieces of the 0.5mm spacers (#34) wall into the bottom U-channel and slip the cut U-channel 2 (bottom profile) (#29) and U-channel 1 (wall profile) U-channel 1 Stationary (#09) onto the Stationary glass (#11) as shown in Fig 13.1. glass With the door open, place the Stationary glass and u-channel U-channel 2...
  • Page 14 Remove the U-channel 1 (76”, wall profile) (#09), U-channel 2 (44”, bottom profile) (#29) and Anti-Water strip (inline wall panel) (#19) from the Stationary glass (#11) wall and set the Stationary glass (#11) aside. Place the U-Channel 2 (bottom profile) (#29) outside onto the threshold base in line with the inside outside...
  • Page 15 Apply waterproof silicone along the bottom waterproof silicone surface and around the holes of the U-Channel 1 (76”, wall profile) (#09). Fasten the U-Channel 1 wall (#09) to the wall with the Countersunk screw ST4.2x40 (#23). Add three or four 2” pieces of the 0.5mm spacers (#34) into the bottom u-channel.
  • Page 16 Notch 1” off of the bottom of the Flanged inside anti-water strip (#33) to fit around bottom U-channel. Press the Flanged anti-water strip (#33) onto the vertical edge of the Stationary glass (#11). outside (Fig 19) 1” inside inside outside outside Fig 19 Mount the Handle (#02) onto the Door Glass...
  • Page 17 . Measure the bottom of the Door Glass (#01) from end to end to determine the actual width of the door. Cut the Bottom anti-water strip (#07) to the size of your measurement and notch 3/8” of the inner side of the Bottom anti-water strip (#07) as shown in Fig 21.2.
  • Page 18 Cut the Flanged anti-water side strip (#33) to the measurements from the previous step. Notch the cut strips to be able to slide them into the Hinges (#05) and around the installed Bottom anti-water strip (#07) to cover the space between both glass panels. Open the door and press the cut strips onto the vertical edge on the hinge side of the Door Glass (#01) so...
  • Page 19 UNIDOOR-X Tub Door manual Ver 1 10/2016...

  • Page 20: Product Maintenance

    NOTE: To maximize the life of your door, it is important to regularly inspect the glass and other hardware for misalignment, proper attachment, and/or damage. Contact DreamLine with any questions or concerns. UNIDOOR-X Tub Door manual Ver 1 10/2016...
  • Page 21 TEL: 866-731-2244 FAX: 866-857-3638 DREAMLINE.COM For more information on DreamLine Shower Doors and Enclosure please visit DreamLine.com ® ©2017 DreamLine. All Rights Reserved...