Huawei UPS5000-S Series Quick Manual
Hide thumbs
Also See for UPS5000-S Series:
- User manual (289 pages) ,
- Quick manual (16 pages) ,
- User manual (202 pages)
Table of Contents
Advertisement
Quick Links
UPS5000-S-(40 kVA-200 kVA)
Quick Guide (IP42, 40 kVA Power
Modules)
Issue: 03
Part Number: 31509861
Date: 2019-06-10
1
Overview
UPS Model
UPS5000-S-
200K-SM-IPB
cable routing
UPS5000-S-200K-SM
1. Before installation, read
the user manual
carefully to get familiar
with product information
and safety precautions.
2. Use insulated tools
during installation and
operation.
3. Only engineers certified
by Huawei or its agents
are allowed to install,
commission, and
maintain the UPS.
Otherwise, personal
injury or equipment
damage may occur, and
the UPS faults caused
are beyond the warranty
scope of Huawei.
4. This document
describes the
installation procedure
for a single UPS. For
details about how to
install a parallel system,
contact Huawei
technical support.
Cabling
Capacity
Mode
Configuration
Bottom
200 kVA
Power modules
Bypass module
Control module
Power distribution
subrack module
Copyright © Huawei Technologies Co., Ltd. 2019. All rights reserved.
Weight (Standard
Configuration)
Net weight ≤ 480 kg
Gross weight ≤ 530 kg
1
Dimensions
(H x W x D)
2000 mm x 600 mm
x 850 mm
Monitoring
display unit
(MDU)
Filler panel
Maintenance
bypass switch
Document
holder
Advertisement
Table of Contents
Related Manuals for Huawei UPS5000-S Series
Summary of Contents for Huawei UPS5000-S Series
- Page 1 UPS5000-S-(40 kVA-200 kVA) Quick Guide (IP42, 40 kVA Power Modules) Issue: 03 Part Number: 31509861 Date: 2019-06-10 Copyright © Huawei Technologies Co., Ltd. 2019. All rights reserved. Overview Cabling Capacity Weight (Standard Dimensions UPS Model Mode Configuration Configuration) (H x W x D) Net weight ≤...
-
Page 2: Installing The Ups
Installing the UPS Secured Installation 1. Determine the cabinet installation position. 6. Remove the four rubber plugs (two front and Mark mounting holes in the installation two rear) from the bottom of the cabinet. position based on drawings. Unit (mm) 7. -
Page 3: Installing Cables
Installing Cables UPS Cable Connection Reference • Prepare cables away from the cabinets to prevent scraps from falling inside. Cable scraps may ignite and cause personal injury or device damage. • After cables have been installed, clean the cabinet in a timely manner. Ensure that there is no foreign matter inside and around the cabinet. - Page 4 3. Connect the ground cables. 4. (Skip this step if the mains and bypass inputs share a power source.) Remove the copper bars between the mains and bypass input wiring terminals. NOTE • : internal equipotential connection label. • : protection ground label. 5.
-
Page 5: Verifying The Installation
7. Connect the battery cable. 8. Connect the signal cable. The number and color of signal cables in the figure are for reference only. Signal cables can be routed along the left or right side of the cabinet. Route signal cables based on the actual situation. Verifying the Installation Cabinet top 1. -
Page 6: Powering On And Starting The Ups
Powering On the UPS Turn on the external bypass and mains input switches. After the UPS is powered on, initialization begins. The MDU displays the Huawei logo and an initialization progress bar. Starting the Inverter Number of Number of Battery... - Page 7 Initial Startup a. During the initial startup, set the language, time and date, network parameters, and system parameters on the Settings Wizard screen. b. After you set parameters on the Settings Wizard screen, the MDU displays the Bypass mode and No battery alarms, which do not need to be handled. If there is any other alarm, you need to rectify the fault.
- Page 8 Download the mobile phone app (Service Expert). Use the app to start the inverter No, start the online? inverter offline Insert the WiFi module into the USB port on the On the MDU, choose System Info > MDU. Choose System Info > Settings > Maintenance >...
-
Page 9: Shutting Down The Ups
Powering On Loads 1. After the inverter starts, the UPS works in normal mode. The Bypass mode alarm disappears from the MDU. 2. After confirming that the battery strings are properly connected, turn on the battery string input circuit breaker. If there are multiple battery strings, turn on the circuit breaker for each battery string and then turn on the general circuit breaker between battery strings and the UPS. - Page 10 Scan here for technical support (carrier): Huawei App Store Scan here for more documents: Support-E Support WeChat You can also log in to Huawei technical support website: http://support.huawei.com/enterprise http://support.huawei.com Huawei Technologies Co., Ltd. Huawei Industrial Base, Bantian, Longgang Shenzhen 518129 People's Republic of China...