Advertisement
Table of Contents
Trouble shooting Bellavita handset
Failure
Led didn't flash
LED is flashing, but bathlift
didn't move.
LED twinkle green during
pressing the UP-button, but
the bathlift don`t move
LED twinkles red (amber) in
spite of fully accu.
The handset should always be switched off before connecting (as well as for use at the
While charging the LED
twinkles red
While charging the LED
twinkles green
LED didn`t flash while
charging
Note:
If there are still problems with the charging mostly a reset will help. To make a
reset, please do twice the selftest but without the relais test, this means switch off
the handset when the red Led is flashing !
Requirements fort he selftest: The accu`s must be charged so that the LED shows green or
amber, not red ! Also the handset should not be connected neither with the bathlift nor with
How to do the selftest, see next page:
Trouble shooting Bellavita Handset
Possible causes
Accupack unplugged from
board inside
Coiled cable overstretched
and thereby unplugged
Handset is not connected
correct – Alert function
Board in a wrong mode
bathlift or charging). !
Board in a wrong mode
Board in a wrong mode
Power supply defective or bad
connected
the power supply.
Stand 11/2009
Trouble shooting
Replace handset
Replace handset
Switch off handset, connect
correct and switch on again.
Switch off handset and
disconnect, the connect again
and switch on.
Here you can also do the
selftest in case of insecurity,
the test must always start with
a green flashing LED !
Disconnect power supply,
Switch on handset- and then
switch off. Connect now first
handset and power supply
and then connect power
supply with the socket.
See above
Check connection, if
necessary replace power
supply.
Page 1 of 2 / HJR
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Drive Bellavita handset
Summary of Contents for Drive Bellavita handset
- Page 1 Trouble shooting Bellavita handset Failure Possible causes Trouble shooting Led didn’t flash Accupack unplugged from Replace handset board inside LED is flashing, but bathlift Coiled cable overstretched Replace handset didn’t move. and thereby unplugged LED twinkle green during Handset is not connected...
- Page 2 Trouble shooting Bellavita handset Selftest for Bellavita Hand Control (PLEASE DISCONNECT UNIT FROM LIFT OR CHARGER) 1. Press the Up- and Down button at 2. Keeping the Up & Down pressed 3. The LED initially flashes green, the same time and keep them then press the ON-Button for a then to amber …...
Need help?
Do you have a question about the Bellavita handset and is the answer not in the manual?
Questions and answers
The bathlift is stuck in the top position. The handset is fully charged but will not lower. Have tried resetting handset as per manual instructions but still the same. When turning on the handset and press the blue button we get a bleep.
The Drive Bellavita handset may not be lowering the bathlift despite being fully charged and reset due to one of the following reasons:
1. Coiled Cable Overstretched – The cable may have been overstretched, causing it to become unplugged. Replacing the handset could resolve this issue.
2. Handset Not Correctly Connected – If the LED twinkles green during the UP-button press but the bathlift does not move, the handset may not be correctly connected. Switching off the handset, reconnecting it properly, and switching it on again may fix the problem.
3. Board in a Wrong Mode – If the LED twinkles red (amber) despite a fully charged battery, the board may be in the wrong mode. Switching off the handset, disconnecting it, reconnecting it, and switching it back on may help.
If the issue persists, performing a self-test starting with a green flashing LED might be necessary.
This answer is automatically generated
@Simon Fisher The bath lift is stuck in the top position. The handset is fully charged but will not lower. Have tried resetting handset as per manual instructions but pressing the yellow button we do not hear a click but continue with the instructions. When turning back on the handset and press the blue button we get a bleep.
@Mr. Anderson The bath lift is stuck in the top position. The handset is fully charged but will not lower. Have tried resetting handset as per manual instructions but pressing the yellow button we do not hear a click but continue with the instructions. When turning back on the handset and press the blue button we get a bleep.
HOW is it dismantled for storage