Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Advantage Controls NanoTron Nano-P Series
Summary of Contents for Advantage Controls NanoTron Nano-P Series
- Page 1 Manual NanoTron P/R P(pH) / R(ORP) Installation Maintenance Repair Manual ENTER Advantage Controls 4700 Harold Abitz Dr. Muskogee, OK 74402 Phone: 918-686-6211 Fax: 888-686-6212 www.advantagecontrols.com 04/2019 email: support@advantagecontrols.com...
-
Page 2: Table Of Contents
Table of Contents Contents Page Introduction ................. 3 Description .................. 3 NanoTron-P/R Features ............. 3 III. Installation Electrical Wiring ................4 Mounting Instructions ..............4 Logic and Relay Cards ............... 5 Electrode Installation ..............6 Front Panel Description .............. 7 NanoTron-P/R Menu Map ............ -
Page 3: Introduction
Introduction NanoTron microprocessor based controllers are designed to provide a wide range of control functions for recirculating water treatment systems. The controller is programmed through a front panel keypad and can be configured to provide a customized control system for your application. Your particular unit’s functions can be determined by comparing the units model number to the Model Numbering table listed below. -
Page 4: Installation Electrical Wiring
6. The electrical installation of the controller must be performed by trained personnel only and conform to all applicable National, State and Local codes. 7. Operation of this product in a manner not specified by Advantage Controls may result in damage to equipment or persons. -
Page 5: Logic And Relay Cards
Logic and Relay Cards Relay Card for W Option Relay Card Relays can be a dry contact by changing Power In the jumpers and POWER SUPPLY connecting to Ground Ground and either N.O. or N.C. Neutral Powered relay output jumper Ribbon Cable configuration... -
Page 6: Electrode Installation
Electrode Installation NanoTron controllers may come configured for various circulating water systems. Listed below are instructions for typical cooling tower and boiler installations. Your specific installation requirements may differ, but should conform to these instructions as much as possible for proper operation. Cooling Tower The standard probe(s) and/or flow assembly for cooling tower installations is constructed of schedule 80 PVC and supplied with 3/4”... -
Page 7: Front Panel Description
Flow Through Probe Assembly FS-FC TFS-C FS-0C 1A9A000262 TFS-OC E-30-PH FS-PT-P pH Probe Paddle Flow Switch PE-21 FS-T used with option -or- OE-21 ORP Probe PE-NUT FS-B1-SP 2C0A-150 E-30-PH Replacement Probes FS-SP NANO-R ......OE-21 Sample Valve NANO-R4 ......OE-21 NANO-R8 ....OE-21SS UNION-3/4TT NANO-P ...... - Page 8 Calibration Alarm List pH Set Relay 2 Set mA Output * Dual pH enable Mode: Timer/Alarm Alarms Yes* ORP/pH Out Scale 20mA ORP/pH = X If Dual pH mode in Nano-P. Relay 1 = falling Relay 2 = rising Only shows in 4mA ORP/pH = X timer mode.
-
Page 9: Nanotron-P/R Menu Map
Water Meter Clock Set Force Setup Diagnostics Pulse Output Configure Password 0000 Reset Meter? N Set Time Force On: Ask Nano-P/R Lo Rate XXXX Force On: Relay1 /pH = X Meter Units Set Date FW: ?.?.? Flow Sw: Close Hi Rate XXXX Force On: Relay2 pH = X Meter Value... -
Page 10: System Operation Overview
System Operation Overview Description of Menus NanoTron controllers have three modes of operation, Run, Menu and Force. All menus are circular. Pressing the DOWN key will display the next line of information on the display. Run - This mode is for normal operation. The control relays will only be automatically active in this mode. -
Page 11: Troubleshooting
VIII. Troubleshooting The Nano-P/R controller is designed for many years of trouble free operation. Should a problem occur, refer to the following chart to help identify the problem. If replacement is required, follow the procedures listed in the Warranty and Factory Service portion of this manual. SYMPTOM POSSIBLE CAUSE SOLUTION... -
Page 12: Warranty & 30 Day Billing Memo Policy
Manufacturer’s Product Warranty Advantage Controls warrants units of its manufacture to be free of defects in material or workmanship. Liability under this policy extends for 24 months from date of installation. Liability is limited to repair or replacement of any failed equipment or part proven defective in material or workmanship upon manufacturer’s examination.
Need help?
Do you have a question about the NanoTron Nano-P Series and is the answer not in the manual?
Questions and answers