Download Print this page
Whirlpool 4LEC7646EN0 Installation Instructions Manual
Whirlpool 4LEC7646EN0 Installation Instructions Manual

Whirlpool 4LEC7646EN0 Installation Instructions Manual

Whirlpool electric dryer use and care guide
Hide thumbs Also See for 4LEC7646EN0:

Advertisement

Quick Links

Have questions about your dryer?
Check your Use and Care Guide
for a toll-free
number
to call, or call your
dealer.
The dealer
is listed in the Yellow
Pages of your
phone
directory
under
"Appliances
-
Household
-
Major
-
Service
and Repair."
When
you call, you will need the dryer
model
number
and serial number.
Both numbers
are on the model/senal
rating
plate located
in the door well
behind
the dryer
door
and on front
of opening.
Record
the
numbers
here for handy
reference:
IR
Model
No.
Serial
No.
Moving dryer to a new location?
Check with
a licensed
electrician
to confirm
that supply
voltage
at new
home
matches
voltage
specified
on the model/serial
rating
plate.
Shut off electrical
supply to dryer. Un lug
power
supply cord and tape it secure y to dryer.
P
(Or disconnect
power
supply cable from dryer.)
Slide dryer onto carddoard
or hardboard
before
moving
it across the floor to
prevent
damaging
floor covering.
G/
Electric Dryer
Part No. 3397625
IMPORTANT:
Read and save these instructions.
Installer:
Leave Installation
Instructions
with
homeowner.
Homeowner:
Keep Installation
Instructions
for future
reference.
For best performance,
install
dryer
according
to
Installation
Instructions.
Failure to complete
installation
as instructed
could
void warranty.
Save
Installation
Instructions
for local electrical
inspector's
use.

Advertisement

loading

Summary of Contents for Whirlpool 4LEC7646EN0

  • Page 1 Have questions about your dryer? Check your Use and Care Guide for a toll-free number dealer. The dealer is listed in the Yellow Pages of your under “Appliances Household Major Service When you call, you will need the dryer model number Both numbers are on the model/senal...
  • Page 2 Check that all parts were included. 4 leveling legs Part No. 3397625 0 1996 Whirlpool Corporation Prepared 1 Parts needed for installation: Check local codes and see electrical and venting requirements, Determine if you will need to purchase...
  • Page 3: Recessed Area/Closet Installation

    42-318 L107.6 -*=__-. “=x I dryer exhaust vent *from floor with dryer feet extended inch (2.5 cm) Recessed area/closet installation klre Hazard Exhaust dryer outside if installed in a closet. Use Exhaust Deflector Kit #3391278 if installed in a recessed area. Failure to follow this instruction could result in a fire.
  • Page 4 Fire Hazard Use a heavy metal vent. Do not use a plastic vent. Do not use a metal foil vent. Failure to do so can result in death or fire. Do Not use non-metal flexible vent, metal vent that is smaller than four inches...
  • Page 5 See installation steps for details. Change door swing. 6. \ Install SLIDE DRYER ONTO CARDBOARD HARDBOARD BEFORE MOVING ACROSS PREVENT FLOOR DAMAC Panel C Check operation. feet. Put on safety glasses and gloves. Install exhaust hood. Use caulking compound to seal exterior wall opening around exhaust...
  • Page 6 Panel D CONFORM WITH THE LOCAL STANDARDS. Be careful not to scratch or chip paint. Open dryer door. Remove bottom screws from cabinet side of hinges (B). Loosen (do not remove) top screws from cabinet side of hinges. Lift door until top screws in cabinet in large part of hinge...
  • Page 7 Panel E Slide dryer onto cardboard or hardboard Move dryer close to its permanent exhaust vent. Remove cardboard hardboard from under dryer. Check levelness of dryer by placing level on top of dryer, first side to side, then front to back. If dryer is not level, adjust dryer legs up or down.