Related Manuals for Aqualisa Quartz Thermo QZ3111
Summary of Contents for Aqualisa Quartz Thermo QZ3111
- Page 1 Quartz ® Thermo Concealed shower valve with adjustable head Quartz Thermo installation guide page 1 For latest prices and delivery to your door visit MyTub Ltd - www.mytub.co.uk - info@mytub.co.uk 0844 556 1818...
- Page 2 Shower systems Components Quartz Thermo built-in shower valve with adjustable head QZ3111 Quartz Thermo installation guide page 2 For latest prices and delivery to your door visit MyTub Ltd - www.mytub.co.uk - info@mytub.co.uk 0844 556 1818...
-
Page 3: Safety Information
A cold inlet flow regulator is provided for use with instantaneous (multipoint) gas water heater and combination boiler applications. If you have any questions at any stage during installation please contact the Aqualisa customer helpline on 01959 560010. Safety information This product must be installed by a competent person in accordance with all relevant current Water Supply Regulations. -
Page 4: Pump Installation
9 litres (2 gallons) per minute to the shower valve. This is sufficient to operate one outlet point at a time. The Aqualisa Thermo cartridge is designed to operate from the mains at a maximum pressure of 10 bar. If the mains pressure exceeds 10 bar a ‘drop tight’... - Page 5 Step-by-step instructions In addition to the guide below it is essential that the written instructions overleaf are read and understood and that you have all the necessary components (shown overleaf) before commencing installation. Failure to install the product in accordance with these instructions may adversely affect the warranty terms and conditions.
- Page 6 Set the temperature control lever to full cold (9 o’clock) prior to removing the four screws securing the lever to the valve. Carefully remove the temperature lever to reveal the lilac temperature preset override ring and the white temperature preset location ring. Neither of these parts need to be removed for installation.
- Page 7 Using a silicone based lubricant, lubricate the supply pipe ends and whilst supporting the elbows, push home the supply pipes ensuring the correct orientation for the inlet pipes (HOT LEFT AND COLD RIGHT AS SHOWN ON THE VALVE BODY). Push the valve fully home until a definite stop is reached (tube insertion depth is 25mm).
- Page 8 Shroud support ring Refit the lilac temperature preset override ring and the white temperature preset location ring if removed prior to installation, taking care to fit the override ring in the correct orientation as outlined in step 5. Prior to replacing the shroud, ensure the shroud seal is in position as indicated.
- Page 9 Ensuring the fixing lugs and locating pins are correctly aligned, carefully place the valve end cap onto the on/off lever and click into position. Adjustable height head installation Prepare pipe work from the shower valve to the required position for the hose outlet using a ø15mm copper pipe.
- Page 10 Drill and plug two holes 642mm-655mm vertically apart using a spirit level if necessary. Fit the rail end clip into position and loosely fit the lower bracket into position. Pass the rail through the handset holder whilst keeping the slider levers depressed with the handset holder pointing in a downward direction.
- Page 11 Connect the hose to the wall outlet assembly after passing it through the gel hook/hose restraint (if required) and run the shower for 15 seconds without the handset attached to clear any internal debris, which may be present. Quartz Thermo installation guide page 11 For latest prices and delivery to your door visit MyTub Ltd - www.mytub.co.uk - info@mytub.co.uk 0844 556 1818...
- Page 12 After installation... Commissioning The Quartz Thermo valve is pre-set to a safe maximum shower temperature. During use, the action of the stop button may be overridden by depressing it as the temperature control is rotated. Should it be necessary to reset the maximum temperature position please observe the following procedures.
-
Page 13: After Installation
After installation Run through the Quartz Thermo operation with the purchaser and hand them this guide. Complete and post the Quartz Thermo guarantee card or register online at www.aqualisa.co.uk Cleaning Your Quartz Thermo shower system should be cleaned using only a soft cloth and washing up liquid. -
Page 14: Troubleshooting Guide
Troubleshooting guide Symptom Possible cause Action Water output is either Reversed inlet supplies Check that the supplies all hot or all cold, correspond with the inlet or cold only markings Water output is not hot The temperature of the hot The cylinder temperature enough water cylinder is too low... -
Page 15: Typical Installations
Typical installations Typical gravity system installation Typical Thermal storage unit system installation Supply Underside of cistern Vent and draw-off pipe to hot water Highest point Cold feed must be 1m below to cylinder underside of cistern Connect ‘A’ or ‘B’ Supply Hot water Hot water... - Page 16 The company reserves the right to alter, change or modify the product specifications without prior warning ® Registered Trademark Aqualisa Products Limited For latest prices and delivery to your door visit MyTub Ltd - www.mytub.co.uk - info@mytub.co.uk 0844 556 1818...
Need help?
Do you have a question about the Quartz Thermo QZ3111 and is the answer not in the manual?
Questions and answers