Toro Flex-Force Power System Operator's Manual
Hide thumbs
Also See for Flex-Force Power System:
- Operator's manual (100 pages) ,
- Operator's manual (12 pages) ,
- Operator's manual (113 pages)
Related Manuals for Toro Flex-Force Power System
Summary of Contents for Toro Flex-Force Power System
- Page 1 Form No. 3432-903 Rev C Flex-Force Power System ™ MAX String Trimmer Model No. 51835T—Serial No. 319000001 and Up *3432-903* Register at www.Toro.com. Original Instructions (EN)
-
Page 2: Important Safety Instructions
II. Preparation Keep bystanders and children away from the operating area. Use only the battery pack specified by Toro. Using other accessories and attachments may increase the risk of injury and fire. Plugging the battery charger into an outlet that is not 100 to 240 V can cause a fire or electric shock. - Page 3 Dress properly—Wear appropriate clothing, battery pack above 68°C (154°F) or incinerate including eye protection; long pants; substantial, it. Replace the battery pack with a genuine Toro slip-resistant footwear; and hearing protection. battery pack only; using another type of battery Tie back long hair and do not wear loose jewelry pack may cause a fire or explosion.
- Page 4 Do not attempt to service or repair the appliance, battery pack, or battery charger except as indicated in the instructions. Have an Authorized Service Dealer perform service using identical replacement parts to ensure that the product is safely maintained. Store an idle appliance indoors in a place that is dry, secure, and out of the reach of children.
-
Page 5: Safety And Instructional Decals
0.08” (2.0mm) diameter nylon line / l en nylon de 2,0 mm (0.08”) de diamètre 60V MAX* DC STR I NG TRIMMER / DÉBROUSSAILLEUSE À FIL *Battery manufacturer rating = 60V maximum & 54V nominal. THE TORO COMPANY TORO EUROPE NV Actua l voltage varies with load. B-2260 OEVEL-WESTERLOO *Tension indiquée par le fabricant de la batterie = 60 V max.,... - Page 6 Setup Loose Parts Use the chart below to verify that all parts have been shipped. Procedure Description Qty. Allen wrench Unfold the shaft. Auxiliary handle assembly Install the auxiliary handle. Guard Install the guard. String trimmer strap (Not included) Install the strap. Note: The battery pack is not fully charged when you purchase it.
- Page 7 Unfolding the Shaft Parts needed for this procedure: Allen wrench Procedure Unfold the shaft (A of Figure Align the locking button on the lower shaft with the slotted hole on the upper shaft and slide the 2 shafts together (B and C of Figure Note: The locking button clicks into the slotted hole when both shafts are secured (D of...
-
Page 8: Installing The Auxiliary Handle
Installing the Auxiliary Handle Parts needed for this procedure: Auxiliary handle assembly Procedure Separate the auxiliary handle from the handle plate by removing the 4 socket head screws using the provided Allen wrench (A of Figure Line up the guides on the auxiliary handle plate to the guide on the bottom of the trimmer shaft (B of Figure Line up the auxiliary handle with auxiliary handle plate on the trimmer shaft (C of Figure... -
Page 9: Installing The Guard
Installing the Guard Parts needed for this procedure: Guard Procedure Using the provided Allen wrench, remove the 2 socket head screws, 2 washers, and 2 spacers from the trimmer base (A of Figure Align the guard onto the trimmer base (B of Figure Secure the guard onto the base of the trimmer with the 2 socket head screws, 2 washers, and 2 spacers previously removed (C of... -
Page 10: Product Overview
Product Overview Operation Specifications Starting the Trimmer Make sure that the vents on the trimmer are Appropriate Temperature Ranges clear of any dust and debris. Charge/store the battery pack 5°C (41°F) to 40°C (104°F)* Use the battery pack at -30°C (-22°F) to 49°C (120°F) Use the trimmer at 0°C (32°F) to 49°C (120°F) Store the trimmer at... -
Page 11: Charging The Battery Pack
Charging the Battery Pack Important: The battery pack is not fully charged when you purchase it. Before using the tool for the first time, place the battery pack in the charger and charge it until the LED display indicates the battery pack is fully charged. -
Page 12: Advancing The Line Manually
Advancing the Line Using Battery pack and/or battery charger is over or under the appropriate temperature range the Bump Feed Battery pack charging fault* blinking Run the tool at full throttle. *Refer to Troubleshooting (page 16) for more Tap the bump button on the ground to advance information. -
Page 13: Operating Tips
Adjusting the Cutting Swath The trimmer comes from the factory with a cutting swath of 36.6 cm (14 inches) as shown in A of Figure Refer to the following instructions to adjust the swath to 40.6 cm (16 inches) as shown in D of Figure Remove the swath blade from the bottom of the guard by removing the 2 screws holding it in place using the provided Allen wrench (B of... -
Page 14: Maintenance
Replacing the String Use only 2 mm (0.080 inch) monofilament string (Toro Part No. 88201) or 2.4 mm (0.095 inch) twisted monofilament string (Toro Part No. 88202). Remove the battery pack. Remove any old string on the spool by... - Page 15 Storage Important: Store the tool, battery pack, and charger only in temperatures that are within the appropriate range; refer to Specifications (page 10). Important: If you are storing the tool for a year or longer, remove the battery pack from the tool and charge the battery pack until 2 or 3 LED indicators turn green on the battery.
-
Page 16: Troubleshooting
Troubleshooting Perform only the steps described in these instructions. All further inspection, maintenance, and repair work must be performed by an authorized service center or a similarly qualified specialist if you cannot solve the problem yourself. Problem Possible Cause Corrective Action The tool does not start. - Page 17 Problem Possible Cause Corrective Action It is difficult to remove the battery pack 1. The battery pack/tool is new or there 1. Clean the terminals on the battery from the tool. is corrosion in the battery terminals pack and the tool with a dry rag. Then and/or the terminals on the tool.
- Page 18 Notes:...
- Page 19 The Toro Company (“Toro”) respects your privacy. When you purchase our products, we may collect certain personal information about you, either directly from you or through your local Toro company or dealer. Toro uses this information to fulfil contractual obligations - such as to register your warranty, process your warranty claim or to contact you in the event of a product recall - and for legitimate business purposes - such as to gauge customer satisfaction, improve our products or provide you with product information which may be of interest.