Huawei U-SYS IAD101H Quick Start Manual
  1. Manuals
  2. Brands
  3. Huawei Manuals
  4. Gateway
  5. U-SYS IAD101H
  6. Quick start manual

Huawei U-SYS IAD101H Quick Start Manual

Integrated access device
Hide thumbs
Table of Contents

Advertisement

Quick Links

U-SYS IAD101H/102H/104H Integrated Access
Device
V300R001C03
Quick Start
Issue
02
Date
2011-02-09
HUAWEI TECHNOLOGIES CO., LTD.

Advertisement

Table of Contents
loading

Related Manuals for Huawei U-SYS IAD101H

Summary of Contents for Huawei U-SYS IAD101H

  • Page 1 U-SYS IAD101H/102H/104H Integrated Access Device V300R001C03 Quick Start Issue Date 2011-02-09 HUAWEI TECHNOLOGIES CO., LTD.

  • Page 3: Table Of Contents

    U-SYS IAD101H/102H/104H Integrated Access Device Quick Start Contents Contents 1 Packing List....................... 2 2 Safety Precautions ....................3 3 Installation ........................ 5 4 Configuration (Command Line Mode) ..............6 4.1 Logging In Through Telnet..................... 6 4.2 IAD(SIP) Accessing NGN/IP PBX ................7 4.3 IAD(MGCP) Accessing NGN/IP PBX ................

  • Page 4: Packing List

    U-SYS IAD101H/102H/104H Integrated Access Device Quick Start 1 Packing List Packing List After you unpack the product package, check the items in the following table. If the tems in the package are different from those in the table, contac t the sales pe rson.

  • Page 5: Safety Precautions

    U-SYS IAD101H/102H/104H Integrated Access Device Quick Start 2 Safety Precautions Safety Precautions Pay attention to the following precautions when installing and using the device. Basic Re qu rements Follow the requirements of the manufacturer to install the device. Do not disassemble the device. Contact the specified maintenance station if the faults occur on the device.
  • Page 6 U-SYS IAD101H/102H/104H Integrated Access Device Quick Start 2 Safety Precautions Avoid scratch or wear and tear on the device shell. Otherwise, the dropped paint may cause allergy or device exceptions. For example, short circuit may be caused if the paint drops into the host.

  • Page 7: Installation

    U-SYS IAD101H/102H/104H Integrated Access Device Quick Start 3 Installation Installation The IAD101H/102H/104H is the case-shaped device. You only need to connect cables. 3. Connect the power-off survival 1. Used for connecting to the uplink port for only IAD101H&102H. Use device. Use a cable to connect to the...

  • Page 8: Configuration (Command Line Mode)

    U-SYS IAD101H/102H/104H Integrated Access Device Quick Start 4 Configuration (Command Line Mode) Configuration (Command Line Mode) You can configure the data of the IAD by using the command line. 4.1 Logging In Through Telnet 4.2 IAD(SIP) Accessing NGN/IP PBX 4.3 IAD(MGCP) Accessing N GN/IP PBX 4.4 IAD(SIP) Accessing IMS...

  • Page 9: Iad(Sip) Accessing Ngn/Ip Pbx

    U-SYS IAD101H/102H/104H Integrated Access Device Quick Start 4 Configuration (Command Line Mode) If you cannot access the IAD by the preceding method, set the IP address of your PC to the same IP address segment as “1.1.1.1” and the subnet mask to 255.255.255.0. If you can ping 1.1.1.1 successfully, enter telnet 1.1.1.1 in the Run dialog box to log in to the IAD.
  • Page 10 U-SYS IAD101H/102H/104H Integrated Access Device Quick Start 4 Configuration (Command Line Mode) Step 2 Configure the IP address of the IAD. There are three methods for obtaining the IP address, that is, Static IP address, DHCP and PPPoE. By default, the IAD obtains an IP address through DHCP automatically after being connected to the network.

  • Page 11: Iad(Mgcp) Accessing Ngn/Ip Pbx

    U-SYS IAD101H/102H/104H Integrated Access Device Quick Start 4 Configuration (Command Line Mode) service is enabled on a PC, choose Control Panel > Management Tools > Services. If the SIP server can function as an SNTP server, you can set the SNTP server to the SIP server.
  • Page 12 U-SYS IAD101H/102H/104H Integrated Access Device Quick Start 4 Configuration (Command Line Mode) TERMINAL(config)#terminal timeout 255 Step 2 Configure the IP address of the IAD. There are three methods for obtaining the IP address, that is, Static IP address, DHCP and PPPoE. By default, the IAD obtains an IP address through DHCP automatically after being connected to the network.

  • Page 13: Iad(Sip) Accessing Ims

    U-SYS IAD101H/102H/104H Integrated Access Device Quick Start 4 Configuration (Command Line Mode) Step 6 (Optional) To prevent illegal MG devices from registering with the MGC server, run the mgcp authentication command to configure the MG authentication information. Step 7 Run write to save your settings.
  • Page 14 U-SYS IAD101H/102H/104H Integrated Access Device Quick Start 4 Configuration (Command Line Mode) Run ipaddress static ip-address subnet-mask default-gateway to set a fixed IP address. Run ipaddress dhcp to obtain an IP address through DHCP. (A DHCP server is required.) Run pppoe username user-name password password to set the PPPoE user name and password, and then run ipaddress pppoe to obtain an IP address through PPPoE.

  • Page 15: Accessing Network Through The Iad

    U-SYS IAD101H/102H/104H Integrated Access Device Quick Start 4 Configuration (Command Line Mode) TERMINAL(advanced-config)#exit Step 5 Run the sip user command to set the users for port 0 and port 1. TERMINAL(config)#sip user 0 id +862821010300 password 111 name +862821010300@sichuan.chinamobile.com TERMINAL(config)#sip user 1 id +862821010301 password 111 name +862821010301@sichuan.chinamobile.com...

  • Page 16: Setting The Ucems Parameters

    U-SYS IAD101H/102H/104H Integrated Access Device Quick Start 4 Configuration (Command Line Mode) 2. Select Obtain an IP address automatically on the PC that is connected to the LAN port of the IAD. The IAD then allocates a LAN IP address to the PC, such as 192.168.100.10.
  • Page 17 U-SYS IAD101H/102H/104H Integrated Access Device Quick Start 4 Configuration (Command Line Mode) type IP address status primary 192.168.1.201 normal secondary <unconfig> unconfiged ------------------------------------------------------------------ ------ get community : public set community : private trap community : public trap port : 162 nms access value: Enable register nms ip : 192.168.1.201...

  • Page 18: Faq

    U-SYS IAD101H/102H/104H Integrated Access Device Quick Start 5 FAQ 1. Q: What is the user name and passw ord for logging in to the IAD? A: The user name is and the password is admin. root Q: How to restore factory settings? A: After logging to the IAD, run the enable and configure terminal commands to enter the global configuration mode.

  • Page 19: Technical Specifications

    U-SYS IAD101H/102H/104H Integrated Access Device Quick Start 6 Technical Specifications Technical Specifications To ensure that the IAD101H/102H/104H runs normally, the IAD101H/102H/104H must meet conditions such as the po wer supply, temp erature, and humidity. Item Specification Power consumption IAD101H: 4.9 W IAD102H: 6.1 W...

This manual is also suitable for:

U-sys iad102hU-sys iad104h

Table of Contents