Toro Groundsmaster 360 Series Operator's Manual
100in rear discharge deck traction unit
Hide thumbs
Also See for Groundsmaster 360 Series:
- Operator's manual (24 pages) ,
- Installation instructions (2 pages) ,
- Operator's manual (60 pages)
Related Manuals for Toro Groundsmaster 360 Series
Summary of Contents for Toro Groundsmaster 360 Series
- Page 1 Form No. 3389-430 Rev B 100in Rear Discharge Deck Groundsmaster ® 360 Series Traction Unit Model No. 31101—Serial No. 315000001 and Up *3389-430* B Register at www.Toro.com. Original Instructions (EN)
-
Page 2: Table Of Contents
Servicing the Bushings in the Caster additional information, contact an Authorized Service Arms ............. 18 Dealer or Toro Customer Service and have the model Servicing the Caster Wheels and and serial numbers of your product ready. The model Bearings............19 and serial numbers are stamped into a plate that is Servicing the Cutting Blades ...... -
Page 3: Safety
Safety • Extinguish all cigarettes, cigars, pipes, and other sources of ignition. • Use only an approved fuel container. This machine has been designed in accordance with EN ISO 5395:2013 and ANSI B71.4-2012. • Never remove fuel cap or add fuel with the engine running. -
Page 4: Toro Mower Safety
The following list contains safety information specific to Toro products or other safety information that you Maintenance and Storage must know that is not included in the CEN, ISO, or ANSI standard. - Page 5 • To best protect your investment and maintain optimal performance of your Toro equipment, count on Toro genuine parts. When it comes to reliability, Toro delivers replacement parts designed to the exact engineering specifications of our equipment. For peace of mind, insist on Toro genuine parts.
-
Page 6: Safety And Instructional Decals
Safety and Instructional Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or lost. decal93-6696 93-6696 1. Stored energy hazard—read the Operator's Manual. decal119-6807 119–6807 1. - Page 7 decal121-5498 121-5498 decal125-9403 125-9403 1. Height-of-cut 3. High 2. Low...
-
Page 8: Setup
Serial range 31223 314000105 and up 30539 314000117 and up All other 4WD models 314000001 and up Note: Revision J or later of the Toro Diagnostic software must be installed in the vehicle controller system to operate the deck as designed. -
Page 9: Product Overview
Attachments/Accessories A selection of Toro approved attachments and accessories is available for use with the machine to enhance and expand its capabilities. Contact your Authorized Service Dealer or Distributor or go to www.Toro.com... -
Page 10: Operation
Operation inch) position there is only one hole, located in the second row. This does not add 6 mm (1/4 inch) to the 127 mm (5 inch) position. Note: Determine the left and right sides of the Adjust the anti-scalp rollers and skids as machine from the normal operating position. -
Page 11: Adjusting The Skid(S)
Toro recommends a blade pitch of Move each skid to the desired position and approximately 8 to 11 mm (5/16 to 7/16 inch). This secure them with the flange-head bolts and nuts. -
Page 12: Operating Tips
Leveling Side to Side Using a short ruler, measure from the floor to the front tip of the blade. If the cut is uneven across the mower swath, correct it Rotate the same blade tip to the rear and as follows: measure from the floor to the tip of the blade at Position the machine on a level surface on the the rear of the mower. - Page 13 A good rule to follow is: decrease ground speed as is damaged or worn, replace it immediately with a the load on the cutting blades increases, and increase genuine Toro replacement blade. Refer to Servicing ground speed as the load on the blades decreases.
-
Page 14: Maintenance
Maintenance Recommended Maintenance Schedule(s) Maintenance Service Maintenance Procedure Interval • Tighten the caster wheel nuts. After the first 2 hours • Tighten the caster wheel nuts. After the first 10 hours • Change the mower deck gearbox lubricant. After the first 50 hours •... - Page 15 g025301 Figure 12 1. Pull link 4. Deck lift chain 2. Torsion spring 5. Retainer pin 3. U-bolts 6. Shoulder screw...
-
Page 16: Lubrication
Lubrication Service Interval: Every 50 hours The machine has grease fittings that must be lubricated regularly with #2 general-purpose, lithium-based grease. If the machine is operated under normal conditions, lubricate all bearings and bushings after every 50 hours of operation or immediately after every washing. -
Page 17: Servicing The Mower Deck Gearbox Lubricant
Remove the dipstick/fill plug from the top of the gearbox (Figure 20) and make sure that the lubricant is between the marks on the dipstick. g025658 Figure 18 • Spindle shaft bearings (5) (Figure g014267 Figure 20 1. Fill plug and dipstick 2. -
Page 18: Servicing The Drive Belts
Servicing the Drive Belts Refer to Figure 21 for routing the drive belts appropriately. decal121-5498 Figure 21 Belt routing Servicing the Bushings in the Caster Arms The caster arms have bushings pressed into the top and bottom of the tube and after many hours of operation, the bushings will wear. -
Page 19: Servicing The Caster Wheels And Bearings
Sharpen the blades as necessary. Remove the locknut from the bolt holding the If a blade is damaged or worn, replace it immediately caster wheel assembly between the caster fork with a genuine Toro replacement blade. (Figure 23). DANGER... - Page 20 (Figure 25). blade is out of balance or is bent. To ensure optimum performance and continued safety conformance of the machine, use genuine Toro replacement blades. Replacement blades made by other manufacturers may result in non-conformance with safety standards.
- Page 21 WARNING Contact with a sharp blade can cause serious injury. Wear gloves or wrap sharp edges of the blade with a rag. Hold the blade end using a rag or a thickly-padded glove. Remove the blade bolt, the anti-scalp plate, and the blade from the spindle shaft (Figure 28).
-
Page 22: Adjusting The Deck-Limit Chains
4 U-bolts Chains (Figure 30). Use 2 deck shims Toro Part No. 138-8243 or 2 feeler gauges—0.15 mm (0.060 inch) Preparing the Deck Start the engine, lower the left and right decks, shut off the engine, remove the key, and wait for all moving parts to stop. - Page 23 g321246 g321239 Figure 33 1. Belt cover 3. Deck shim 2. Inner-channel tab (outer deck) Note: If you are using feeler gauges, use a piece of tape to adhere a feeler gauge—0.15 mm (0.060 inch) to the tab of the inner channel (Figure 34).
- Page 24 g321234 Figure 35 1. Deck shim (or feeler 5. U-bolt gauge) 2. Serrated-flange nut 6. Front of the machine g321243 Figure 34 (outboard) 3. Pivot link 7. Serrated-flange nut 1. Inner-channel tab 3. Front of the machine (inboard) 2. Feeler gauge 4.
- Page 25 Repeat steps in Assembling the Shim to the Deck (page 22) Tensioning the Chains (page 24) for the other mower deck. g321235 Figure 36 1. Deck shim (or feeler 5. Serrated-flange nut gauge) (inboard) 2. Pivot link 6. Front of the machine 3.
- Page 26 The method of transmission shall be electronic transmittal. This machinery shall not be put into service until incorporated into approved Toro models as indicated on the associated Declaration of Conformity and in accordance with all instructions, whereby it can be declared in conformity with all relevant Directives.
- Page 27 Countries Other than the United States or Canada Customers who have purchased Toro products exported from the United States or Canada should contact their Toro Distributor (Dealer) to obtain guarantee policies for your country, province, or state. If for any reason you are dissatisfied with your Distributor's service or have difficulty obtaining guarantee information, contact the Toro importer.