SunSetter VISTA Series Manual
  1. Manuals
  2. Brands
  3. SunSetter Manuals
  4. Accessories
  5. Vista Series
  6. Manual
SunSetter VISTA Series Manual

SunSetter VISTA Series Manual

Protective cover for vista and motorized awnings
Hide thumbs Also See for VISTA Series:
1
2
3
4

Advertisement

Table of Contents

Protective Cover - VISTA and Motorized Awnings

WARNING:
FAILURE TO WEAR SAFETY GLASSES OR TO FOLLOW THE INSTRUCTIONS BELOW COULD
RESULT IN PERSONAL INJURY.

Tools Needed:

• Measuring tape,
• pencil,
• step ladder,
• chalk line,
• 1/8" drill bit,
• Philips screwdriver.
For masonry installation only:
• 3/16" masonry bit.

Installing the Wall Fasteners for the Protective Cover

Note: We recommend installing the wall fasteners for the Protective Cover one at a time.
Begin with the one to the far right. Once
the first fastener is installed, use the actual
Protective Cover as the template for the
grommet spacing between all the holes.
1. Locate the supplied Fasteners and Screws used
to secure the Protective Cover to the wall.
2. Measure up 3/4" from the top of the Wall Brackets
and make a mark on the wall.
See Figure 1.
©SunSetter Products, a Massachusetts Limited Partnership, 184 Charles Street, Malden, MA 02148
RETRACTABLE AWNINGS
For Technical Support visit us at http://ownerscorner.sunsetter.com
or Call Toll Free 800-670-7071 • Fax 877-224-4944
Installed with Wall Brackets
Parts Included:
• Long Phillips Screws
• Short Phillips Screws
• Plastic Anchors
• Wall Fasteners
• Cords
• Cord Locks
• Safety Clips
• Vinyl Cover
8-12 ft
13-17ft
12
16
12
16
12
16
6
8
6
8
6
8
6
8
1
1
End of
1st Fastener
Awning
1"
Location
#6 Philips head screws
(2 Places)
Figure 1
18-20ft
20
20
20
10
10
10
10
1
Cover
3/4"
Fastener
Chalk line
for Cover
HOUSE
Fasteners
Wall Bracket

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the VISTA Series and is the answer not in the manual?

Questions and answers

Related Manuals for SunSetter VISTA Series

Summary of Contents for SunSetter VISTA Series

  • Page 1 2. Measure up 3/4” from the top of the Wall Brackets #6 Philips head screws and make a mark on the wall. (2 Places) See Figure 1. Figure 1 Wall Bracket ©SunSetter Products, a Massachusetts Limited Partnership, 184 Charles Street, Malden, MA 02148...
  • Page 2 3. On the mark, snap a level chalk line along the entire length of the Awning. On the chalk line, mark the location of the right end of the Awning. Along the chalk line you just made, measure 1” further to the right of the Awning end point and make a mark.
  • Page 3 5. Repeat with remaining Safety Clips, Cords, Gears, and Cord Locks. Figure 3 Figure 4 Figure 5 Ends of Cord Gear Cord through Cord Lock (White or Black) Cord Lock Gear in Cord Lock ©SunSetter Products, 184 Charles Street, Malden, MA 02148...
  • Page 4 3. Stow each Safety Clip for future use by looping the Cord around the Square Bar and attaching the Clip to the Cord. DO NOT REMOVE Cord from the Square Bar. 4. Plug in the electrical cord to use the Awning. SunSetter Products, 184 Charles Street, Malden, MA 02148 INSMCV-CoverMotorized.pdf July 29, 2019...

Table of Contents