Table of Contents
Related Manuals for Toshiba TDP-D1
Summary of Contents for Toshiba TDP-D1
- Page 1 OWNER’S MANUAL DLP DATA PROJECTOR TDP-D1 TDP-D2...
-
Page 2: Safety Precautions
- Consult the dealer or an experienced radio/TV technician for help. WARNING: Changes or modifications made to this equipment, not expressly approved by Toshiba, or parties authorized by Toshiba, could void the user’s authority to USA only operate the equipment. - Page 3 IMPORTANT SAFETY INSTRUCTIONS (Continued) 5. Heat 8. Power-Cord Protection The product should be situated Power-supply cords should be away from heat sources such as routed so that they are not likely to radiators, heat registers, stoves, or be walked on or pinched by items other products (including placed upon or against them, amplifiers) that produce heat.
- Page 4 IMPORTANT SAFETY INSTRUCTIONS (Continued) 16. Damage Requiring Service 18. Servicing Unplug this product from the wall Do not attempt to service this outlet and refer servicing to product yourself as opening or qualified service personnel under removing covers may expose you the following conditions: to dangerous voltage or other a) When the power-supply cord or...
-
Page 5: Power Supply Cord Selection
DECLARATION OF CONFORMITY TRADE NAME: DLP DATA PROJECTOR MODEL NAME: TDP-D1/ TDP-D2 RESPONSIBLE PARTY: TOSHIBA AMERICA INFORMATION SYSTEMS, INC. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. -
Page 6: Table Of Contents
EXEMPTION CLAUSES • Toshiba Corporation bears no responsibility in the case of damages arising from natural disaster such as earthquakes, lightning, etc., fire not liable to Toshiba Corporation, operating by third parties, other accidents, or use under abnormal conditions including erroneous or improper operation and other problems. -
Page 7: Checking The Package Contents
Checking the package contents Please make sure that the following items are included in the box, along with the main unit. If an item is missing, please contact the store from which you purchased the product immediately. (11) (12) (10) (1) Remote control (7) RGB cable (2) R03 (SIZE AAA) batteries for remote... -
Page 8: Names Of Each Part On The Control Panel And Remote Control
Names of each part on the control panel and remote control Control Panel Remote Control Laser emitter (10) Remote control LAMP TEMP transmitter ON/STANDBY INPUT MENU VOL. VOL. AUTO KEYSTONE AUTO SET Caution Label Caution - use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. -
Page 9: Preparing And Using The Remote Control
Preparing and using the remote control I Loading dry-cell batteries I Operating the remote control into the remote control Point the remote control toward the q Remove the battery cover. projector’s infrared remote sensor, and press a button on the remote control. -
Page 10: Connection
Connection Before connection • Read the owner’s manual of the device to be connected to the projector. • Some types of computer cannot be used connected to this projector. Check for an RGB output terminal, supported signal p.36 • Turn off the power of both devices before connection. •... -
Page 11: Basic Operations
Turning the power on and off (Continued) Notes • The start-up screen will disappear after a moment. You can dismiss the start-up screen before this by performing any operation. You can also configure the start-up screen not to appear via the Display setting menu p.29 •... -
Page 12: Using Handy Features
Basic operations (Continued) Projector placement angle adjustments The placement angle and the height of the projected image can be adjusted by the foot adjuster. q Lift up the front of the projector until it is at the desired angle, then press the foot adjuster release button. -
Page 13: Correcting The Keystone Distortion (Keystone)
Using handy features (Continued) I Correcting the keystone distortion (Keystone) p.22 When the foot adjuster is used to change the projection angle, the picture will undergo keystone (trap- ezoidal) distortion. This projector is capable of correcting this keystone distortion. Before correction After correction Press the AUTO KEYSTONE button. -
Page 14: Displaying Information [Status Display]
4: Displays [Lamp time] as a measure of when the lamp should be replaced. (Cannot be used as a counter of guaranteed lamp time.) When the time displayed approaches 1,500 hours, consult with a store about getting a replacement lamp (for TDP-D1: TDPLD1 and for TDP-D2: TDPLD2) (sold separately) prepared. -
Page 15: The Image Adjustment Menu
Using the menu (Continued) I The image adjustment menu Use this menu to adjust image-related items. Items Items that can be adjusted are marked with “Yes”, and those that cannot are marked with “No”. Item Description Computer Y/P Contrast Lower Higher Brightness Darker... -
Page 16: Operating A Computer By The Remote Control
® slides, etc. • When replacing, always use the specified lamp (for TDP-D1: TDPLD1 and it for TDP- D2: TDPLD2) (sold separately). • If you have been using the projector, the lamp will be very hot, and may cause burn injuries. -
Page 17: Trouble Indications
Lamp replacement (Continued) Remove the lamp cover. Loosen the screws and remove the lamp cover. Pull out the lamp. Loosen the three screws holding the lamp in place, and pull on the handle to remove the lamp. Mount the new lamp. Align the orientation, press down until the bottom is reached, and lock in place using the three lamp locking screws. -
Page 18: Before Calling Service Personnel
Before calling service personnel If you think something is wrong, check the following before contacting customer service. p.33 Please see “Trouble indications” as well. If This Happens Check • Is the power cord plugged in? Is it connected to the projector? No power •... - Page 19 Specifications (Continued) I List of supported signals (RGB signals) This projector supports the following RGB signals. Note, however, that depending on the computer model, the screen may show flicker or streaking. Please adjust the projector if this happens. (Press the AUTO SET button, and adjust automatically or manually. Refresh rate Resolution Mode...
-
Page 20: Specifications
ACK (06h) ESC (1Bh) No acknowledge NAK (15h) Command Computer input select Video input select S-video input select Model NO.; for TDP-D1: TDPLD1, for TDP-D2: TDPLD2 Description Receiving data Consent to send Data set ready Signal ground Request to send...