Sealey ELECTROSTART E/START800HY Instructions

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
refer to Warning!:
instruction explosive risk
manual
1. SAFETY
Modern vehicles contain extensive electronic systems.
You are required to check with the vehicle Manufacturer, for any specific instructions regarding the use of this type of
equipment on each vehicle. No liability will be accepted for damage / injury, where this product is not used in accordance
with all instructions.
ensure that the vehicle is in a well ventilated area.
9
Apply the handbrake and select neutral or 'park' before attempting to start.
9
ensure that the ignition switch and all ancillary electrical equipment is switched off.
9
Keep clear of any pulleys, belts etc. that will move once the engine starts.
9
take care to ensure correct connection polarity; red clamp to positive, black clamp to negative.
9
energise the e/stArt800HY only at ambient temperatures between -30°c and 40°c.
9
When not in use, switch off and store in a cool, dry place out of the reach of children.
9
DO NOT allow this power pack to become wet.
8
DO NOT dismantle this e/stArt800HY: there are no user serviceable parts inside.
8
DO NOT use in explosive atmospheres (e.g. the presence of flammable liquids, gases or dust).
8
DO NOT use the e/stArt800HY if it appears damaged in any way.
8
DO NOT use this product for any purpose other than that for which it is designed.
8
DO NOT leave in direct sunlight or expose to heat.
8
DO NOT use abrasive or solvent cleaners on this product.
8
DO NOT allow children to play with this product
8
DO NOT allow the positive and negative clamps to touch.
8
BATTERY SAFETY
1.1.
WARNING! To reduce the risk of burns or fire:
‰
DO NOT attempt to open, disassemble, modify or service the battery pack.
8
DO NOT crush, puncture, short external contacts or dispose of in fire or water.
8
DO NOT expose to temperatures above 60°c (140°).
8
replace only with the battery pack designated for this product.
9
recycle or dispose of used battery as stipulated by local regulation.
9
if the electrolyte in the cells gets on your skin, thoroughly wash with soap and water. if it gets in your eyes, rinse thoroughly with cool
8
water and seek immediate medical attention.
2. INTRODuCTION
Vehicle jump starting made easy with innovative patented technology. unlike traditional boosters it does not require an internal battery as a
primary power source but incorporates a lithium battery pack to energise the capacitors when vehicle battery is not sufficient. Simply connect to
the vehicle's battery, even if discharged and the unit will draw enough power to energise itself in a matter of minutes. Power can then be pushed
safely back through the starting system to jump start the vehicle. if the vehicle battery is faulty or is holding less than 5 volts the e/stArt800HY
can be pre-charged via an internal lithium battery pack, another vehicle's battery, a micro usB charging cable (not supplied) or 12V accessory
lead. the digital display indicates battery voltage, capacitor charge and faults. the internal battery can hold its charge whilst not in use and
without a battery to charge the device is ready to use in a matter of minutes. compact and lightweight for easier handling and storage, yet still
delivers the same result as heavy, lead acid battery equivalents. ideal for both professional mechanics and diY users.
3. SPECIFICATION
model no: ......................................................e/stArt800HY
output: .............................................................................12V
output start peak (en): ...................................... 800A (400A)
maximum starting capacity: .................... petrol 3ltr, diesel 2ltr
cable & clamp length: ................................................ 500mm
size (W x d x H):.......................................130 x 50 x 195mm
lithium Battery: ................................................ 7.4V, 4400mA
usB output: ................................................................. 5V 2A
© Jack sealey limited
instructions for
ELECTROSTART ® BATTERYLESS POWER START
800A 12V
E/START800HY
model no:
Wear eye Wear protective
protection gloves
Original Language Version
Warning!:
electricity
e/stArt800HY | issue:2 21/07/17