Page 1
FusionModule5000 Smart Modular Data Center V100R001 Maintenance Guide Issue Date 2016-10-18 HUAWEI TECHNOLOGIES CO., LTD.
Page 2
Notice The purchased products, services and features are stipulated by the contract made between Huawei and the customer. All or part of the products, services and features described in this document may not be within the purchase scope or the usage scope. Unless otherwise specified in the contract, all statements, information, and recommendations in this document are provided "AS IS"...
About This Document About This Document Overview This document describes FusionModule5000 Smart Modular Data Center (Smart Module for short) in terms of the routine maintenance, alarm references, troubleshooting, and parts replacement, which helps maintenance personnel to inspect and maintain the Smart Module and eliminate potential risks promptly.
To improve the troubleshooting efficiency and avoid misoperations, maintenance personnel must obtain the work permit and understand the related operation procedure. Critical troubleshooting tasks should be performed by qualified personnel trained by Huawei. Maintenance personnel should also be clear of the following during maintenance: ...
2.1 Routine Maintenance for the Power Supply and Distribution System. If the alarm is not cleared after performing operations described in related documents, contact Huawei technical support. 3.2 Alarms for the Cooling System For details about alarms for a cooling component, see the documents delivered with it. When unpacking the equipment, collect the documents delivered with it.
2.1 Routine Maintenance for the Power Supply and Distribution System. If the fault persists after performing operations described in related documents, contact Huawei technical support. 4.2 Troubleshooting the Cooling System To rectify faults of a cooling component, see the documents delivered with it.
Page 25
If the fault is rectified, no further action is required. If the fault persists, check the operating status of the condenser fan. − If the fan fails to run properly, contact Huawei technical support. − If the fan runs properly, go to Step Step 4 Check whether the amount of refrigerant is proper.
If yes, troubleshoot the air conditioners and contact Huawei technical support. If no, contact Huawei technical support. Step 4 Check whether humidification parameters of the air conditioners are set correctly. Check whether humidification parameters of the air conditioners are set correctly.
− If the fault is rectified, no further action is required. − If the fault is not rectified, contact Huawei technical support. If no, contact Huawei technical support. ----End 4.2.3 Water Accumulates Near Air Conditioners Symptom Water accumulates on the floor near air conditioners.
If the indicator lights on, the fault is rectified, and no further action is required. If the indicator does not light up and the fault persists, contact Huawei technical support. ----End Issue 01 (2016-10-18) Huawei Proprietary and Confidential...
If yes, replace the cables and check whether the fault is rectified. − If the fault is rectified, no further action is required. − If the fault is not rectified, contact Huawei technical support. If no, but the fault persists, contact Huawei technical support. ----End 4.3.4 Troubleshooting Camera Faults...
Step Step 4 Check whether the IP address of the camera is correctly set. If yes, but the fault persists, contact Huawei technical support. If not, reset the IP address and check whether the fault is rectified. −...
If yes, replace the cables and check whether the fault is rectified. If the fault is rectified, no further action is required. − − If the fault is not rectified, contact Huawei technical support. If no, but the fault persists, contact Huawei technical support. ----End 4.3.6 Troubleshooting the Alarm Beacon...
Immerse the cable into the water and check whether the alarm is displayed on the NetEco. If yes, but the fault is not rectified, contact Huawei technical support. If no, replace the water sensor and check whether the fault is rectified.
Step 5 Check whether the access controller works properly. Use a spare access controller to check whether the access control system works properly. If yes, no further action is required. If no, contact Huawei technical support. ----End 4.3.10 Troubleshooting Double-Door or Four-Door Access Controller Faults Symptom A double-door or four-door access controller fails to control the door properly.
If the fault is rectified, no further action is required. If the fault is not rectified, contact Huawei technical support. ----End 4.3.11 Troubleshooting Double Door Magnetic Lock Faults Symptom The double door magnetic lock cannot be opened properly.
Step 1 Observe the emergency door release button and check whether the button is broken. If yes, install a new emergency door release button. If no, but the fault persists, contact Huawei technical support. ----End Issue 01 (2016-10-18) Huawei Proprietary and Confidential...
Maintenance Guide 5 Parts Replacement Follow-up Procedure If the hard disk works abnormally, contact Huawei technical support. 5.4.5 Replacing a Dome Camera Dome cameras can be installed in various scenarios. This section describes how to replace a dome camera on the control skylight.
----End Follow-up Procedure Send the faulty smoke detector with a Repair Notice to your local Huawei office for repair. You can check whether the new smoke detector works properly by viewing the smoke detector status displayed on the event bar of the screen.