Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for QERIDOO Sportrex1 2019
Summary of Contents for QERIDOO Sportrex1 2019
- Page 1 USER MANUAL Q3-19-A Q3-19-DA Q3-19-DW Q6-19-A Q6-19-DA Sportrex1 2019 Q6-19-DW Sportrex2 2019 GERMAN ENGINEERING DESIGN This product fulfils all safety requirements of the European standard for bicycles and bicycle trailers (DIN EN 15918).
- Page 2 When necessary, individual items of information can be changed quickly and without special notification. This documentation can be ordered from Qeridoo GmbH in other languages, or is available for down- load on our website if already available.
-
Page 3: Table Of Contents
Contents Introduction Mounting the coupler onto a bicycle Proper use Installing the rear light Performance limits Utilisation Operating the parking brake Notes on the user manual Adjusting the push handle Safety instructions Setting the mode Users Adjusting the buggy wheel Conditions of use Insert tow bar Passenger... -
Page 4: Introduction
Introduction Proper use Sportrex was designed as a bicycle trailer and comes with an additional buggy and walker function. For Trailer mode, use a tow bar with coupler to connect the trailer to a suitable towing vehicle (bicycle or motorised pedelec with a maximum speed of 25 km/h). With the buggy wheel attached, the Sportrex can be used as a child carrier in Buggy mode. -
Page 5: Notes On The User Manual
Introduction MAX. MAX. Size MAX. MAX. Children may be transported up to a maximum size where the head does not exceed the maximum line on the backrest. The following additional restrictions apply to Trailer mode: Requirements for the tow bar Sportrex1 &... -
Page 6: Safety Instructions
Safety instructions Danger! Read the safely instructions below carefully. The safety and accident prevention regulations valid in your region and statutory rules such as the road traffic regulations also apply, and take precedence in cases where there is doubt. Make sure that the Sportrex is used only by persons suitable for its operation, as defined below. -
Page 7: Passenger
Install and use only original accessories and spare parts manufactured or recommended by ƒ Qeridoo. Using other products relieves the manufacturer of liability. Only carry out structural modifications or extensions to the vehicle which are necessary ƒ for the use of the approved accessories in accordance with the assembly instructions. Any further manipulation that is not expressly approved by the manufacturer in writing relieves the manufacturer of liability in the event of accidents and defects. -
Page 8: Cycling With A Trailer
Safety instructions Cycling with a trailer The way in which the bicycle moves changes significantly when it is pulling a trailer, and this is particu- larly noticeable when braking and cornering. With regard to this, pay attention to the following: Practice cycling with the trailer before going out onto the road. -
Page 9: Product Overview
Product overview Scope of delivery Pennant with 2-part pennant staff and Head protectors (2x) centre piece 2 wheels Tow bar with coupler and retaining strap Multiwheel buggy wheel Push handle with hand strap and hand park- Leaf suspension cover ing brake with side-mounted parking brake module* and brake cable 10 Wheel axle with suspension Cabin with seats and 5-point safety... -
Page 10: Components And Control Elements
Product overview Components and control elements Side view 12 12 Cabin (frame made from aluminium tubes 11 Tow bar for trailer mode with cotter pin fas- with weatherproof fabric cover) tening and retaining strap for securing bicy- cle frame 3-in-1 canopy to protect against insects and splash water with integrated sun visor, 12 Tow bar holder rollable... -
Page 11: Rear View
Product overview Components and control elements Rear view Height adjustable push handle with hand Hand parking brake parking brake 10 Star grip screw with tube clamp for securing Splash water cover, rollable the push handle Push button for adjusting the height of the 11 Ventilation window with integrated pouch push handle for small items... -
Page 12: Assembly
Assembly Below you can read all the information that you will need to assemble your Sportrex properly. For a better demonstration of some assembly steps, the fabric cover of the trailer has been removed from the photos and the instruction video, this is not necessary for the assembly. Make sure that you have sufficient space to assemble it. -
Page 13: Inserting The Wheels
Assembly Hold the wheel axle with the leaf springs to the lead spring seat. Turn the four screws through the leaf spring in the leaf spring seat. Tighten the screws with the hexagon socket head cup screws firmly. Make sure that the red leaf spring plates align paral- lel with the silver leaf spring seat so that the axle is centered. -
Page 14: Installing The Head Protectors
Assembly Slide the leaf spring cover onto the slide holder as shown in the picture. Be sure that the fixing mechanism locks audibly. Repeat the procedure on the other side of the trailer. Installing the head protectors The head protectors serve as additional side protection in case the trailer should tip over. Be sure that the slide covers for the head protector are fixed and tightened on both sides. -
Page 15: Inserting The Pennant
Assembly Put the cabin in the upright position and open the cover. Check the tension of the 4 black belts under the seat and tighten them firmly. Make sure that the side Velcro straps inside the vehicle are closed, connecting the side seat cushions with the side wall. -
Page 16: Installing The Brake Cable
Assembly Installing the brake cable Pass the entire brake cable including the splitter through the left opening in the storage space cover. Open the storage space cover. Pass the short end of the brake cable through the left opening in the cabin floor and the long end through the right opening in the cabin floor. -
Page 17: Reinsert The Brake Cable
Assembly Reinsert the brake cable Insert the barrel-shaped end piece of the brake cable into the recess of the toggle. Then place the toggle and brake cable into the socket of the parking brake module‘s cover. Place the cover on the parking brake module and screw it back in place using the previously loosened screws. -
Page 18: Adjusting The Buggy Wheel
Assembly Adjusting the buggy wheel Set with the mode selector switch [A] and the release button (unlock key) [B] in front of the suspension the desired operating mode: Buggy mode: Buggy wheel rotatable through 360 °. – Walker mode: Buggy wheel running straight. –... - Page 19 The provided universal coupler is suitable for mounting on the most rear-wheel models. If it does not fit your bicycle, find a suitable adapter and special couplers in our manuals on the following website: www.qeridoo.de/kupplungsleitfaden Sportrex 2019 Update Subject to change. 08|2019 – 19...
-
Page 20: Installing The Rear Light
Assembly Caution! Do not use a tool which was previously in contact with conventional steel. Smallest steel particles could be transferred that could lead to contact corrosion. Installing the rear light In trailer mode, a certified rear light must be used during poor visibility or darkness in accordance with the Road Traffic Licensing Requirements. -
Page 21: Utilisation
Utilisation Below you will find all the information for adapting the Sportrex to the required modes and to allow you to use all the convenience functions. Operating the parking brake Danger! Apply the parking brake to secure the Sportrex in order to prevent it from rolling away. Also remember to release it before you set off. -
Page 22: Setting The Mode
Utilisation Setting the mode You can use the Sportrex in one of the following modes: Trailer mode: Carrying children in the Sportrex when cycling ƒ Buggy mode: Using the Sportrex like a buggy ƒ Walker mode: Carrying children in the Sportrex when walking ƒ... -
Page 23: Insert Tow Bar
Utilisation Tip! Carry the buggy wheel e.g. in the storage space in order to allow you to use the Sportrex flexibly at your destination. Instructions for re-mounting it can be found in the chapter „Installing the buggy wheel“ on page 17. Setting the wheel so that it turns freely (Buggy mode) It must be possible for the wheel to move freely through 360°... -
Page 24: Embarking The Children
Utilisation Filling the pouch for small items Put those utensils into the pouch for small items which you want to have readily to hand while you are on the road. If necessary, open the top toggle fasteners and unroll the splash water cover. Fix the splash water cover using the toggle fasteners on the side and underneath. -
Page 25: Strapping In Children
Utilisation Strapping in children Pull the red strap under the seat forward to release the tension on the seat belts. Keep the red strap pulled, so that you can adjust the length of the seat system straps. Choose a suitable length so that the child can be strapped comfortably. -
Page 26: Adjusting The Seat System
Utilisation Danger! Before every journey, check that the safety harnesses and harness catches are sitting cor- rectly. Failure of the restraining function can result in serious or even fatal injuries in the event of an accident. Start driving only when all children either wear a cycling helmet or use a head rest and are properly belted. -
Page 27: Checking The Weight Distribution And Tow Bar Load
Utilisation Adjust the left and right seat belts to the same position and length. Loosen the Velcro fastener for the belt pad fixation as described in section „Adjusting the position of the seat belts“ on page 26. Position the left or right pair of seat belt pads in the middle position using the inner slots of the left and right positions. -
Page 28: Connecting The Trailer To A Bicycle
Utilisation Determine the tow bar load by making a comparison with the previous measured value: The weight must be at least 3 kg more than the – measured value without the tow bar. The weight may be a maximum of 8 kg more than the –... -
Page 29: Decoupling The Trailer
Utilisation Danger! Always make sure the safety strap is in place before using the product in trailer mode. In addition, make sure that the safety strap can not get into moving parts of the towing bike. Danger! Always secure the tow bar to the bicycle frame with the retaining strap. This ensures that the trailer will remain connected even if the tow bar becomes detached from the coupler. - Page 30 Utilisation Danger! Never ride with the cover open. As a minimum, the insect net must be closed in order to provide protection against stones. In bad weather or heavy traffic, also close the weather canopy. Stow away the 3-in-1 canopy Roll up the 3-in-1 canopy.
-
Page 31: Adjusting The Suspension
Utilisation Adjusting the suspension The leaf springs of the Sportrex are adjustable by simply moving the clamps. Caution! Make sure that the resilience is suitable for the current load each time you drive. If you hear strokes while driving over bumps, then the suspension is set too softly. Immediately adjust the setting by moving the clamp towards the wheel axle. - Page 32 Utilisation Caution! Only fold up the cabin after it has been cleaned both inside and outside and is completely dry. Caution! Despite the use of weather proof material, the corrosion cannot be completely eliminated. De-icing salts such as magnesium chloride can lead to stress corrosion cracking on the components.
-
Page 33: Care And Maintenance
The storage location should be dry, well ventilated and protected against direct sunlight. ƒ At higher storage temperatures, you should store the wheels separately from the cabin because the ƒ tyres’ rubber can cause odours. Use a Qeridoo folding garage if the Sportrex must be kept outdoors. ƒ Sportrex 2019 Update... -
Page 34: Maintenance Intervals
Care and maintenance Maintenance intervals Caution! Replace corroded steel and aluminium parts immediately. Never bend back deformed or bent aluminium parts (danger of breakage). Replace bent aluminium parts immediately. Immediately replace plastic parts that have become porous or fragile due to the effects of the weather, for example. -
Page 35: Appendix
Appendix Technical data External dimensions Sportrex1 Sportrex2 Length (Trailer mode) 160 cm 160 cm Width (external width from wheel to wheel) 72 cm 82 cm Height (from ground to cabin roof) 89 cm 89 cm Height of push handle 47.5 cm / 117 cm 47.5 cm ... -
Page 36: Warranty Terms
In the event of replacement, the replaced product will become the property of Qeridoo. If the product is no longer held by Qeridoo, a product of a similar type and quality will be replaced at Qeridoo's option. -
Page 37: Spare Parts
Appendix Spare parts (valid from 2019) Frame components Pos. Article Article No. Sportrex1 Article No. Sportrex2 Coupling bicycle connection accessory 2019 KUFA-19 KUFA-19 Tow bar head with hexagon socket from 2018 Z-DEIK-6K-18 Z-DEIK-6K-18 Cotter pin with rubber safety for bicycle coupling 2019 Z-SMGFFK-19 Z-SMGFFK-19 Multiwheel from 2017 set... - Page 38 Appendix Other spare parts Locking button tow bar mount 2019 Belt pad right 2019 Art.-No.: Z-VKDA-19 Art.-No.: Z-GPR-19 Star knob for handle bar M6 from Crotch pad 2017 2017 Art.-No.: Z-SCHPO-17 Art. no.: Z-SGFH-M6-17 Adjustment leaf suspension Set Head rest 2019 Art.
- Page 39 Appendix Wheel guard left 2018 Art.-No.: Z-RAL-18 leaf suspension cover left 2019 Art.-No.: Y-BFAL-19 leaf suspension cover right 2019 Art.-No.: Y-BFAR-18 Slide adapter 2018 Art.-No.: Y-SCHA-18 Safety strap tow bar 2019 Art.-No.: Z-SBD-19 Buggywheel adapter 2017 Art.-No.: Z-LRAM-17 Buggy Multiwheel 8.5" 2017 Art.-No.: Z-LRMW-8.5-17 Hub axle for Multiwheel...
- Page 40 Sportrex 2019 Update Qeridoo GmbH Industriepark Nord 100, 53567 Buchholz, Germany www.qeridoo.de info@qeridoo.de...
Need help?
Do you have a question about the Sportrex1 2019 and is the answer not in the manual?
Questions and answers