Measurement made easy Introduction For more information — AWT210 This Communications Supplement provides Further publications for the AWT210 transmitter are 2-Wire transmitter procedures specifically related to the AWT210 available for free download from: FOUNDATION Fieldbus™ 2-wire transmitter. Refer to www.abb.com/measurement...
AW T 2 1 0 F O U N D AT I O N F I E L D B U S 2 - W I R E T R A N S M I T T E R | C O M/A W T 2 1 0/ F I E L D B U S - E N R E V. A Health & Safety Document symbols Potential safety hazards AWT210 transmitter – electrical Symbols that appear in this document are explained below: DANGER – SERIOUS DAMAGE TO HEALTH WARNING – BODILY INJURY...
Direct current supply only. ABB is committed to ensuring that the risk of any environmental damage or pollution caused by any of This symbol, when noted on a product enclosure or its products is minimized as far as possible.
Fieldbus Foundation organization website www.fieldbus.org ABB Ltd and its affiliates are not liable for damages and/or losses related to such security breaches, any unauthorized or the ABB website: access, interference, intrusion, leakage and/or theft of data or www.abb.com/fieldbus...
AW T 2 1 0 F O U N D AT I O N F I E L D B U S 2 - W I R E T R A N S M I T T E R | C O M/A W T 2 1 0/ F I E L D B U S - E N R E V. A 5 Transmitter functionality and 4 Device overview operator interface controls Four variants of AWT210 are available for use with pH, ORP, pION, and conductivity sensors. Process interface Sensor Input Channels Supported sensors: •...
Both bus terminators must always be powered to ensure fault-free operation, therefore it is strongly Linking device recommended that they are connected to a back-up power supply. Power conditioner Power supply FF – H1 AWT210 2-wire transmitters Figure 1 Typical FOUNDATION Fieldbus network...
NOTICE specification: Impedance 135 to 165 Ω Property damage Capacitance per unit length <30 pf/m When connecting an AWT210 to a FOUNDATION Fieldbus Loop resistance 110 Ω/km network: Core diameter 0.64 mm • Use cable that meets FOUNDATION Fieldbus Core cross section >0.34 mm...
AW T 2 1 0 F O U N D AT I O N F I E L D B U S 2 - W I R E T R A N S M I T T E R | C O M/A W T 2 1 0/ F I E L D B U S - E N R E V. A Configuration Local configuration The configuration of FOUNDATION Fieldbus communications for an AWT210 transmitter can be set locally using the keypad and menus however it is recommended that the configuration is set remotely by a FOUNDATION Fieldbus master. Menu Used to configure the communications.
This section contains descriptions of the FIELDBUS commands Device-specific command details such as data bytes and available through the FIELDBUS universal, common practice response codes are described in the AWT210 FIELDBUS field and device specific command sets. device specification (COM/AWT210/FIELDBUS-FDS-EN).
Page 11
AW T 2 1 0 F O U N D AT I O N F I E L D B U S 2 - W I R E T R A N S M I T T E R | C O M/A W T 2 1 0/ F I E L D B U S - E N R E V. A Index Parameter Access...
AW T 2 1 0 F O U N D AT I O N F I E L D B U S 2 - W I R E T R A N S M I T T E R | C O M/A W T 2 1 0/ F I E L D B U S - E N R E V. A …8 Fieldbus slots Analog Input function blocks (AI1) (AI2) Index...
AW T 2 1 0 F O U N D AT I O N F I E L D B U S 2 - W I R E T R A N S M I T T E R | C O M/A W T 2 1 0/ F I E L D B U S - E N R E V. A …8 Fieldbus slots pH Transducer block (TB0) Index...
Page 19
AW T 2 1 0 F O U N D AT I O N F I E L D B U S 2 - W I R E T R A N S M I T T E R | C O M/A W T 2 1 0/ F I E L D B U S - E N R E V. A Acknowledgements •...
Page 20
We reserve the right to make technical changes or modify the contents of this document without prior notice. With regard to purchase orders, the agreed particulars shall prevail. ABB AG does not accept any responsibility whatsoever for potential errors or possible lack of information in this document.