Lafayette Parasol Accu-Rise Installation Instructions Manual

Cellular shades

Hide thumbs

Table of Contents

Quick Links

Installation Instructions

•

Accu-Rise

™

•

Angles and Specialty Shapes

•

Arches, Circles and Quarter Circles

•

Auto-Lift

•

Continuum

™

•

Cord Lock

•

Glissade

™

•

Lift & Lock

•

Sidelights

•

SkyFrame

™

•

SkyLite

Manual

™

•

SkyLite w/ Auto-Lift

•

SlideArch

™

• Sure-Lift

™

• System II

*Click

BACK

on any page to return to the Table of Contents*

Cellular Shades

Table of Contents

Troubleshooting

Need help?

Do you have a question about the Parasol Accu-Rise and is the answer not in the manual?

Questions and answers

Summary of Contents for Lafayette Parasol Accu-Rise

Page 1 Cellular Shades Installation Instructions • Accu-Rise ™ • Angles and Specialty Shapes • Arches, Circles and Quarter Circles • Auto-Lift ® • Continuum ™ • Cord Lock • Glissade ™ • Lift & Lock • Sidelights • SkyFrame ™ • SkyLite Manual ™...
Page 2: Install The Brackets
Cellular Window Shades Accu-Rise Installation Instructions Thank you for choosing Parasol Cellular Shades. With proper installation and care, your new shades will provide many years of beauty and performance. Tools Needed Fastener Mounting Surface Power Drill, 1/4” Driver and drill bits Wood #6 Hex Head Tape Measure...
Page 3: End Mount
End Mount INSTALL THE BRACKETS Cont. End Mount " - Position the end mount brackets so that the top of the Minimum attached installation brackets equal the ordered height of the shade. Mounting surface must be vertical and flat. - Mount brackets using the screws provided. Drywall Ordered mounting is not recommended.
Page 4: Remove The Shade
REMOVE THE SHADE For Monaco and Riviera Materials - Lower the shade approximately 4”. Adjust the Shade Height (If Necessary) If the shade height needs adjusted or the bottom rail is - While holding the headrail, push back on the bottom tab not level, the cord on the underside of the bottom rail may of the installation bracket to release the bottom edge of need adjusting.
Page 5: Troubleshooting
Troubleshooting Problem The shade is hard to raise or lower, or will not raise or lower. Solution Make sure that the shade fabric is not caught between the installation bracket and the headrail. Check that the headrail and installation brackets are level and aligned. Shim the installation brackets to level the headrail, if necessary.
Page 6 Cellular Window Shades Angles and Specialty Shapes Installation Instructions Thank you for choosing Parasol Cellular Shades. With proper installation and care, your new shades will provide many years of beauty and performance. Tools Needed Fastener Mounting Surface Power Drill, 1/4” Driver and drill bits Wood #6 Hex Head Tape Measure...
Page 7 INSTALL THE BRACKETS Cont. INSTALL THE SHADE Non-Operable Outside Mount (C.) Operable - Standard Brackets - (A.) - Center the headrail over the window opening at the - Position the shade so cords face you. desired height and lightly mark each end on a flat - Slip headrail into the installation brackets so the front mounting surface.
Page 8: Level The Bottom Rail (If Necessary)
LEVEL THE BOTTOM RAIL (If Necessary) INSTALL THE SHADE Cont. - Lift the bottom rail to locate the pockets on the Non-Operable Sharing Headrail w/Rectangular Shade underside of the rail. - Install rectangular shade into end mount brackets. (End mount bracket installation instructions can be - Gently pull down on the bottom rail to fully insert the found with the rectangular shade).
Page 9 INSTALL CORD TENSION LOCK REMOVE THE SHADE The revised American National Standard Standard Installation Brackets - (A.) for Safety of Corded Window Covering - Fully raise the shade. products requires if corded window - Loosen the tab screw on each installation bracket to products are used in the home, cord headrail.
Page 10 Troubleshooting Problem The shade will not fit into the installation brackets. Solution Check that the installation brackets are level and aligned. Shim the installation brackets to level the headrail, if necessary. Be sure the heads of the screws are flush against the installation bracket. Check that the headrail is completely inserted into the installation brackets. See “Install the Operable Shade” Problem The shade is hard to raise or lower, or will not raise or lower.
Page 11 Cellular Window Shades Arches, Circles and Quarter Circles Installation Instructions Thank you for choosing Parasol Cellular Shades. With proper installation and care, your new shades will provide many years of beauty and performance. Tools Needed Fastener Mounting Surface Power Drill, 1/4” Driver and drill bits Wood #6 Hex Head Tape Measure...
Page 12 INSTALL THE BRACKETS - STAND-ALONE ARCH Outside Mount (A.) - Center the arch over the window opening at the desired height and lightly mark each end on a flat mounting surface. - Mark 3” from each end of the headrail. 3" - Center the installation brackets or extension brackets on your marks and mount level and flush against a flat Additional Installation Bracket mounting surface using the screws provided.
Page 13 PREPARE THE ARCH SHARING A HEADRAIL WITH A INSTALL THE ARCH SHARING A HEADRAIL WITH A CORDLOCK SHADE CONTINUUM, ACCU-RISE, SURE-LIFT OR AUTO-LIFT HEADRAIL - Remove the left end cap from the rail. On Top-Down/ Bottom-Up or 2-On-1 Headrail shades, pull the left - The headrail of the shade has a magnetic strip attached cordlock out 1/2”.
Page 14 INSTALL THE BRACKETS - QUARTER CIRCLE SHADE Outside Mount Outside Mount (A.) - Center the quarter circle shade over the window opening at the desired height and lightly mark each end on a flat mounting surface. 3" - Mark 3” in from each end of the rails. Important: Be sure the bracket locations allow for the quarter circle to completely cover the window opening.
Page 15 INSTALL THE QUARTER CIRCLE SHADE PREPARE THE QUARTER CIRCLE SHADE A. Standard - The shade has two rails: one horizontal and one - Install both the horizontal rail and the vertical rail into vertical rail the installation brackets. - Fit the long side of the specialty end mount bracket into the small fabric channels on the horizontal rail.
Page 16 SUPPORT CLIPS OR HOOKS FOR ARCH OR INSTALL ARCH/QUARTER ARCH INTO CLIPS/HOOKS QUARTER ARCH - Support the fabric as you install the arch Arch Support Clips (if applicable) - If a center support cord is used: - Attach clips to the mounting surface throught the hole * Loosen the screw on the top arch support clip or hook.
Page 17 PREPARE THE CIRCLE SHADE INSTALL THE CIRCLE SUPPORT CLIPS OR HOOKS - Stand the cylinder up with the loose cords at the top. Outside Mount (A.) The top becomes the outside curve of the circle. - Use a ruler and a level to place the clips at the widest vertical and horizontal points of the circle.
Page 18 Cellular Window Shades Auto-Lift Installation Instructions ™ Thank you for choosing Parasol Cellular Shades. With proper installation and care, your new shades will provide many years of beauty and performance. Tools Needed Fastener Mounting Surface Power Drill, 1/4” Driver and drill bits Wood #6 Hex Head Tape Measure...
Page 19 INSTALL THE BRACKETS (Cont.) C. End Mount End Mount (C.) - Position the end mount brackets so that the top of the " attached installation brackets are at the ordered Minimum height of the shade. - Mark both screw holes for each end mount bracket. Mounting surface must be vertical and flat.
Page 20: Connect The Power Source
INSTALL THE SHADE (Cont.) Battery Wand Clip (High Mount – Standard) Battery Wand Clip - Attach the battery wand clip to the headrail. Important: Position the clip so that the battery wand will be between installation brackets. - Hook the battery wand clip onto the back channel of the headrail.
Page 21: Dc Power Supply
CONNECT THE POWER SOURCE (Cont.) DC Power Supply - Plug the power cable from the shade into the extension DC Power cable, and plug the other end of the extension cable Supply Power Cable into the DC power supply. from the Shade - Plug the DC power supply into a standard outlet.
Page 22 LEVEL THE BOTTOM RAIL (If Necessary) For Monaco and Riviera Material - Lift the bottom rail to locate the pockets on the Adjust the Shade Height (If Necessary) underside of the rail. If the shade height needs adjusted or the bottom rail is not level, the cord on the underside of the bottom rail may - Gently pull down on the bottom rail to fully insert the need adjusting.
Page 23: Troubleshooting
Troubleshooting If your shade is not operating correctly: First review the guide that came with your remote control or wireless wall switch. ■ Next refer to the following troubleshooting procedures below for the specific solutions for your shade. ■ Problem The shade will not fit into the installation brackets. Solution Check that the installation brackets are level and aligned. Adjust and/or shim to level, if necessary. Be sure the heads of the mounting screws are flush against the installation bracket.
Page 24: Inside Mount
Cellular Window Shades Continuum Installation Instructions ™ Thank you for choosing Parasol Cellular Shades. With proper installation and care, your new shades will provide many years of beauty and performance. Tools Needed Fastener Mounting Surface Power Drill, 1/4” Driver and drill bits Wood #6 Hex Head Tape Measure...
Page 25 INSTALL THE BRACKETS Cont. End Mount End Mount - Position the end mount brackets so that the top of the attached installation brackets equal the ordered height " Minimum of the shade. Mounting surface must be vertical and flat. - Mount brackets using the screws provided. Drywall mounting is not recommended.
Page 26 LEVEL THE BOTTOM RAIL (If Necessary) For Monaco and Riviera Materials - Lift the bottom rail to locate the pockets on the Adjust the Shade Height (If Necessary) underside of the rail. If the shade height needs adjusted or the bottom rail is not level, the cord on the underside of the bottom rail may - Gently pull down on the bottom rail to fully insert the need adjusting.
Page 27 Troubleshooting Problem The shade is hard to raise or lower, or will not raise or lower. Solution Check that the cord tensioner is mounted correctly. See the instructions included with your Universal Cord Tensioner Installation Kit. For Bottom-Up/Top-Down and Day/Night shades: The lift cords in the headrail may have “overturned”. Try the following: If both rails are in the raised stacked position, at the top of the window, pull down the back cord of ■...
Page 28 Cellular Window Shades Standard Cordlock Installation Instructions Thank you for choosing Parasol Cellular Shades. With proper installation and care, your new shades will provide many years of beauty and performance. Tools Needed Fastener Mounting Surface Power Drill, 1/4” Driver and drill bits Wood #6 Hex Head Tape Measure...
Page 29 INSTALL THE BRACKETS (cont.) Specialty End End Mount Small Fabric Channels ( 3 /8" Pleat Rail Similar) Mount Bracket - On the end without the cords, remove the end cap from the headrail.. - Insert the short end of the specialty end mount bracket under the small fabric channels in the headrail.
Page 30 OPERATE THE SHADE REMOVE THE SHADE Standard Brackets - Standard Bottom-Up and Top-Down shades have one operating cord. Two-on-one, Duo-Lucent, - Fully raise the shade. and Top-Down/Bottom-Up shades have two - While holding the headrail, loosen the tab screw on operating cords.
Page 31 Troubleshooting Problem The shade will not fit into the installation brackets. Solution Check that the installation brackets are level and aligned. Shim the installation brackets to level the headrail, if necessary. Be sure the heads of the screws are flush against the installation bracket. Check that the headrail is completely inserted into the installation brackets. See “Install the Shade” Problem The shade is hard to raise or lower, or will not raise or lower.
Page 32 Problem The bottom rail is not level, or the shade height is incorrect. Solution Shade Height Adjustment Bottom Rail Pocket Shade height and adjustments to level the bottom rail can be made by adjusting the cord on the underside of the bottom rail. Ferrule Pull cord Locate the ferrule seated in a pocket in the bottom rail.
Page 33 Cellular Window Shades Glissade Installation Instructions Thank you for choosing Parasol Cellular Shades. With proper installation and care, your new shades will provide many years of beauty and performance. Tools Needed Fastener Mounting Surface Power Drill, 1/4” Driver and drill bits Wood #6 Hex Head Tape Measure...
Page 34 INSTALL THE BRACKETS Inside/Ceiling Mount - Snap a shim onto the top of each installation bracket. Important: You must attach shims to the installation brackets to allow for valance attachment. If you are not installing a valance, shims are not necessary. - Mark 8”...
Page 35: Install The Rails
PREPARE THE RAILS (Cont.) Center Pull Plate - Split Stack Only - Measure and mark the center of the headrail on the Front of cord tensioner channel. Headrail - Position the center pull plate on the underside of the Cord Tensioner headrail.
Page 36 INSTALL THE RAILS (Cont.) Stationary Rail - Remove any end plates that are attached to the Slots headrail. - The stationary rail bracket has two slots at the top. The rear tracks of the headrail fit into these. - Insert the stationary rail bracket onto the back track of the headrail.
Page 37 INSTALL THE HEADRAIL - Measure and mark the center point on the mounting The front of the bracket surface and the headrail’s center point. fits under the groove. Bracket - Align the headrail by matching the marks. - Slip the headrail into the installation brackets, with the front of the bracket fitting under the groove of the headrail.
Page 38 FINAL SHADE ADJUSTMENTS Remove Excess Cord - Pull on the end of the cord at the cord tensioner to release the slip knot. - With the cord tensioner approximately 12” from the end plate, pull on the cord to create tension and retie a square knot at the cord tensioner.
Page 39 ATTACH THE VALANCE - Slide the valance clip under the bottom lip of the headrail. (A.) Valance Clip - Rotate the valance clip up to snap it into place on the headrail. (B.) Headrail - Keep a minimum of 3” between the end of the headrail and the valance clips.
Page 40 REMOVE THE SHADE (Will need two people) CARE AND CLEANING - Detach the stationary rail bottom bracket from the wall Regular light dusting with a feather duster is all the or floor. cleaning that is needed in most circumstances. For deeper cleaning, vacuum gently with a soft brush - Grasp the top of the valance and rotate the valance attachment.
Page 41 Troubleshooting (Cont.) Problem On inside or ceiling mount applications, there isn't enough room above the mounted installation brackets to angle and attach the headrail and/or the valance. Solution Add a shim to each installation bracket to provide additional space to attach the headrail and/or valance.
Page 42 Cellular Window Shades Lift & Lock Installation Instructions Thank you for choosing Parasol Cellular Shades. With proper installation and care, your new shades will provide many years of beauty and performance. Tools Needed Fastener Mounting Surface Power Drill, 1/4” Driver and drill bits Wood #6 Hex Head Tape Measure...
Page 43: End Mount
INSTALL THE BRACKETS (cont.) End Mount Specialty End Small Fabric Channels - Line up the bracket top with the desired height of the ( 3 /8" Pleat Rail Similar) Mount Bracket top of the headrail. - Mark holes for screws. Brackets must be level. Remove brackets and drill holes.
Page 44: Remove The Shade
REMOVE THE SHADE LEVEL THE BOTTOM RAIL (IF NECESSARY) Standard Brackets If the bottomrail or the middle moving rail of a - Fully raise the shade. top-down/bottom-up shade is not level, it can be adjusted by following the procedure: - While holding the headrail, loosen the tab screw on each bracket to release the headrail.
Page 45 Cellular Window Shades Cordless Operable Sidelights Installation Instructions Thank you for choosing Parasol Cellular Shades. With proper installation and care, your new shades will provide many years of beauty and performance. Tools Needed Fastener Mounting Surface Power Drill, 1/4” Driver and drill bits Wood #6 Hex Head Tape Measure...
Page 46 B. Inside Mount INSTALL THE BRACKETS (cont.) Inside Mount (B.) Standard Bracket Swivel Bracket - Measure 1” from each jamb for bracket location. 2" - Mount brackets using the screws provided. Be sure the 2" front edges of the brackets are aligned and level to each other.
Page 47 ATTACH THE BOTTOM RAIL REMOVE THE SHADE - Allow the shade to hang freely. Standard Brackets - Fully raise the shade. - The bottom rail should be approximately 1” above the bottom mounted brackets. - While holding the headrail, loosen the tab screw on - Pull down on the bottom rail (to engage the spring in each bracket to release the headrail.
Page 48 Troubleshooting Problem The shade will not snap into the mounting brackets. Solution Make sure mounting brackets are level. Loosen the tab screws slightly. Problem The shade does not raise and lower evenly. Solution Check the installation brackets. Make sure the shade fabric is not caught between the bracket tab and the headrail.
Page 49: Installation Instructions
Cellular Window Shades SkyFrame Installation Instructions ™ Thank you for choosing Parasol Cellular Shades. With proper installation and care, your new shades will provide many years of beauty and performance. Tools Needed Fastener Mounting Surface Power Drill, 1/4” Driver and drill bits Wood #6 Hex Head Tape Measure...
Page 50 INSTALL THE SHADE Standard Brackets - Position the shade so the front fabric faces you. - Slip the headrail into the installation brackets so the front of the bracket slides under the front groove on the Headrail top of the headrail. - Gently roll the back of the headrail up and push back to snap into place.
Page 51: Operate The Shade
INSTALL THE FABRIC STRIP - Center the fabric strip on the anchor rail, angle and insert into the back channel of the anchor rail. Fabric Strip - Gently bow the fabric strip and insert the other edge into the front channel of the anchor rail. The side track not shown for clarity.
Page 52 REMOVE THE SHADE CARE AND CLEANING Standard Brackets Regular light dusting with a feather duster is all the - Fully raise the shade. cleaning that is needed in most circumstances. For deeper cleaning, vacuum gently with a soft brush - While holding the headrail, loosen the tab screw on attachment.
Page 53 Cellular Window Shades SkyLite Manual Operation Installation Instructions ™ Thank you for choosing Parasol Cellular Shades. With proper installation and care, your new shades will provide many years of beauty and performance. Tools Needed Fastener Mounting Surface Power Drill, 1/4” Driver and drill bits Wood #6 Hex Head Tape Measure...
Page 54 ASSEMBLE THE SHADE (Cont.) Back - Inside Mount shades only: The light gap seals should Front of Shade be inserted into the front channel of all four rails. Make Shade sure they are inserted in the correct orientation. If the angle of the installed shade will be 45 or steeper, slide the two spacer blocks into the rear channel on the underside of the bottom rail.
Page 55 ASSEMBLE THE SHADE (Cont.) Secure the Side rails to the Top Rail - Hook one end of the bead chain between the third and fourth bead from the end in the slot in the top left corner bracket. (A.) - Pull the bead chain taut and secure the other end of the bead chain in the slot in the top right corner bracket.
Page 56 ASSEMBLE THE SHADE (Cont.) Adjust the Tension - Remove the masking tape and tighten all the top tension screws in the top rail until tension plates line up with the mark. Attach the Crank Handle (Optional) - Unscrew and remove the control knob. - Attach the handle using the screws provided.
Page 57: Inside Mount
INSTALL THE SHADE Inside Mount - Trim the excess light gap seal at all four corners with sharp scissors. - Mount the installation brackets. Important: If you have Bottom Crank an optional crank handle, you will need clearance to Rail Handle fully rotate the handle.
Page 58: Outside Mount
INSTALL THE SHADE Outside Mount - Your order will include four installation brackets, two Installation for each side rail, as well as one 3/8” screw and two Bracket 1 1/2” screws per installation bracket. Important: You may need another person to assist you with this installation.
Page 59 Troubleshooting Problem The shade operates in the opposite direction. Solution Verify that the side rails are installed in the correct orientation. Problem The shade stops before hitting the bottom rail. Solution Adjust the tension brackets so that the tension cables are parallel to the side rails.
Page 60: Tools Needed
Cellular Window Shades SkyLite with Auto-Lift Operation Installation Instructions ™ ™ Thank you for choosing Parasol Cellular Shades. With proper installation and care, your new shades will provide many years of beauty and performance. Tools Needed Fastener Mounting Surface Power Drill, 1/4” Driver and drill bits Wood #6 Hex Head Tape Measure...
Page 61 ASSEMBLE THE SHADE (Cont.) Back - Inside Mount shades only: The light gap seals should Front of Shade be inserted into the front channel of all four rails. Make Shade sure they are inserted in the correct orientation. If the angle of the installed shade will be 45 or steeper, slide the two spacer blocks into the rear channel on the underside of the bottom rail.
Page 62 ASSEMBLE THE SHADE (Cont.) Secure the Side rails to the Top Rail - Hook one end of the bead chain between the third and fourth bead from the end in the slot in the top left corner bracket. (A.) - Pull the bead chain taut and secure the other end of the bead chain in the slot in the top right corner bracket.
Page 63: Connect The Power Source
ASSEMBLE THE SHADE (Cont.) Adjust the Tension - Remove the masking tape and tighten all the top tension screws in the top rail until tension plates line up with the mark. CONNECT THE POWER SOURCE Slot Battery Wand Battery - Install the batteries into the battery wand. Wand - Squeeze the cap latch to release the cap and remove from the battery wand.
Page 64 CONNECT THE POWER SOURCE (Cont.) DC Power Supply - Remove the bottom rail cover and route the power cable from the shade through the bottom left corner bracket. Plug into the extenstion cable. - Reinstall the bottom rail cover and plug the other end of the extension cable into the DC power supply.
Page 65 INSTALL THE SHADE Inside Mount - Trim the excess light gap seal at all four corners with sharp scissors. - Mount the installation brackets. Important: If you have an optional crank handle, you will need clearance to Bottom Crank Rail fully rotate the handle.
Page 66: Operate The Shade
INSTALL THE SHADE (Cont.) Outside Mount - Your order will include four installation brackets, two Installation for each side rail, as well as one 3/8” screw and two Bracket 1 1/2” screws per installation bracket. Important: You may need another person to assist you with this installation.
Page 67 REMOVE THE SHADE (If Necessary) Inside Mount - Raise the shade to the top. If there are screws attaching the side rails to the window frame, unscrew them. - Insert a screwdriver at the lower corners of the shade and push back the brackets to release the lower end of the shade.
Page 68 Troubleshooting If your shade is not operating correctly: First review the guide that came with your remote control or wireless wall switch. ■ Next refer to the following troubleshooting procedures below for the specific solutions for your shade. ■ Problem The battery-powered shade does not operate using the manual control button. Solution Check to be sure batteries in the battery wand(s) are new or fresh. Replace the batteries, if necessary. See “Replacing the Batteries”...
Page 69: Install The Brackets
Cellular Window Shades SlideArch Installation Instructions ™ Thank you for choosing Parasol Cellular Shades. With proper installation and care, your new shades will provide many years of beauty and performance. Fastener Tools Needed Mounting Surface Power Drill, 1/4” Driver and drill bits Wood #6 Hex Head Provided...
Page 70: End Mount
INSTALL THE BRACKETS (Cont.) 3 /4" Pleat Rail Specialty End End Mount Small Fabric Channels Mount Bracket - Slightly remove the end caps from the headrail. Do not remove them all the way. - Insert the short end of the specialty end mount brackets over each of the end caps and under the small fabric channels in the headrail.
Page 71 INSTALL THE TOP CORD GUIDE - Thread the cord loop at the top of the arch through the Cord Loop At Top Of Shade center of the top cord guide. Insert - Put the insert into the top cord guide and seat the cord into the “track”...
Page 72 Troubleshooting Problem The top cord guide does not reach the top of the window opening. Solution Decrease Tension / Lengthen the Center Cord Ferrule Open the shade by pulling the handle all the way to the Pocket left. Hole Locate the cord from the right hole next to the pocket Handle (see illustration).
Page 73 Troubleshooting (Cont.) Problem The fabric rubs against the window casement while opening or closing the shade. Solution Adjust the Shade Before trimming the shade, be sure that the bottom rail is level. Shim if necessary. Also check that the top cord guide is directly above the center of the shade.
Page 74 Cellular Window Shades Sure-Lift Installation Instructions ™ Thank you for choosing Parasol Cellular Shades. With proper installation and care, your new shades will provide many years of beauty and performance. Fastener Mounting Surface Tools Needed Power Drill, 1/4” Driver and drill bits Wood #6 Hex Head Provided...
Page 75 INSTALL THE BRACKETS Cont. End Mount End Mount - Position the end mount brackets so that the top of the " attached installation brackets equal the ordered height Minimum of the shade. Mounting surface must be vertical and flat. Ordered - Mount brackets using the screws provided.
Page 76: Remove The Shade
REMOVE THE SHADE Bracket - Lower the shade approximately 4”. - While holding the headrail, push back on the bottom tab Back of Headrail of the installation bracket to release the bottom edge of Shade the headrail. - After releasing the bottom edge, roll the back of the headrail down and out from the bracket.
Page 77 Troubleshooting Problem The shade is hard to raise or lower, or will not raise and lower. Solution Make sure that the shade fabric is not caught between the installation bracket and the headrail. Check that the headrail and installation brackets are level and aligned. Shim the installation brackets to level the headrail, if necessary.
Page 78: Tools Needed
Cellular Window Shades System II Installation Instructions Thank you for choosing Parasol Cellular Shades. With proper installation and care, your new shades will provide many years of beauty and performance. Tools Needed Fastener Mounting Surface Power Drill, 1/4” Driver and drill bits Wood #6 Hex Head Tape Measure...
Page 79 Inside Mount Inside Mount - Measure 2” from each jamb for bracket location. If more than two brackets came with your order, space additional brackets evenly between the two and mark their location. - Caution: When using high mount battery bracket (standard), you will need 18 1/4”...
Page 80: Install The Battery Wand
INSTALL THE SHADE The front of the bracket - To mount the headrail, hold the shade so the front of the fits under the groove. headrail faces you. Bracket - Slip the headrail onto the installation brackets, so that the front of the bracket fits under the groove of the Snap headrail.
Page 81 CONNECT THE POWER SOURCE DC Power Supply DC Power - Plug the power cable from the shade into the extension Supply Power Cable cable, and plug the other end of the extension cable from the Shade into the DC power supply. - Plug the DC power supply into a standard outlet.
Page 82 Radio Frequency FCC Compliance: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
Page 83 Troubleshooting If your shade is not operating correctly: • First review the guide that came with your remote control or wireless wall switch. • Next refer to the following troubleshooting procedures below for the specific solutions for your shade. Problem The shade will not fit into the installation brackets. Solution Check that the installation brackets are level and aligned. Adjust and/or shim to level, if necessary. Be sure the heads of the mounting screws are flush against the installation bracket.

This manual is also suitable for:

Parasol angles and specialty shapes Parasol auto-lift Parasol arches Parasol continuum Parasol cord lock Parasol glissade ... Show all

Lafayette Parasol Accu-Rise Installation Instructions Manual

Quick Links

Troubleshooting

Need help?

Questions and answers

Related Manuals for Lafayette Parasol Accu-Rise

Summary of Contents for Lafayette Parasol Accu-Rise

This manual is also suitable for:

Table of Contents