Download
Share
Print this page
Target 3-2-1 Cube Assembly Instructions Manual
  1. Manuals
  2. Brands
  3. Target Manuals
  4. Indoor Furnishing
  5. 3-2-1 Cube
  6. Assembly instructions manual

Target 3-2-1 Cube Assembly Instructions Manual

Hide thumbs

Advertisement

Quick Links

3-2-1 Cube
style
dpci
finish
1115
002-11-0842 White
2115
002-11-0843 Espresso
>> assembly instructions

Advertisement

loading
Need help?

Need help?

Do you have a question about the 3-2-1 Cube and is the answer not in the manual?

Questions and answers

Related Manuals for Target 3-2-1 Cube

Summary of Contents for Target 3-2-1 Cube

  • Page 1 3-2-1 Cube style dpci finish 1115 002-11-0842 White 2115 002-11-0843 Espresso >> assembly instructions...

  • Page 2: Introduction

    Congratulations on your latest Target purchase. Now what? Don’t start sweating over this box of parts. This will be easy. We did the hard work for you. All you need to do is follow our simple instructions and you’ll be on your way to transforming your room in no time.

  • Page 3: Table Of Contents

    table of contents introduction hardware parts list safety precautions helpful hints installing L-bracket assembly 9-16 weight capacity/care instructions QUESTIONS? Just call 1-800-874-0008 for parts and service. For faster service, have the style number and DPCI number ready when calling.

  • Page 4: Hardware

    hardware (H1) x 16 (H2) x 20 (H3) x 20 pre-glued dowel assembly screw screw cover #10 x 1-1/2 in. (H4) x 1 (H5) x 1 (H6) x 1 L-bracket screw wall screw L-bracket #10 x 1/2 in. flathead #10 x 1-1/2 in.

  • Page 5: Parts List

    ITEM DESCRIPTION QUANTITY side panel - left top/side panel - right large horizontal divider large vertical divider small horizontal divider small vertical divider bottom panel...

  • Page 6: Safety Precautions

    safety precautions warning • This unit contains small parts which could be a choking hazard for small children. Children should be under adult supervision at all times or serious injury could occur. • Always unload unit prior to moving the unit. The weight of personal belongings can cause the unit to become unstable and either tip or collapse. Serious bodily injury and/or damage to personal belongings may occur.

  • Page 7: Helpful Hints

    helpful hints We recommend you protect your work surface during assembly to prevent scratching or damage to table tops, wood floors, etc. finished edge unfinished edge Unfinished edges are shaded in gray. It is important to understand how finished edges go together. Take a moment to lay out all the wood pieces and note the finished and unfinished (raw wood) edges.

  • Page 8: Installing L-Bracket

    installing L-bracket There are several "key points" to L-bracket installation. Please review the wall Install short end against wall/wall drawings and comments at right as well stud stud; long end against unit. as the assembly steps provided. All units must be fastened to the wall. short Always mount L-bracket to a wall-stud.

  • Page 9: Assembly

    step 1. warning Do NOT force dividers together. May cause damage to panels if forced. 1. Align dividers (E) and (C) with cut outs facing upwards as shown. 2. Position remaining dividers (D) and (F) above first set of dividers as shown with cut outs facing downwards. 3.
  • Page 10 step 2. (H2) (H2) (H2) (H2) x 2 assembly screw #10 x 1-1/2 in. 1. Align screw holes where dividers (F) and (E) meet. 2. Secure both dividers to each other using two assembly screws.
  • Page 11 step 3. (H1) (H1) (H1) (H1) (H1) (H1) (H1) (H1) (H1) x 12 (H1) pre-glued dowel (H1) (H1) (H1) (H1) 1. Quickly dip pre-glued dowel into a cup of water, making sure entire dowel gets wet. 2. Immediately push two dowels into center holes on both unfinished edges of each large divider as shown. 3.
  • Page 12 step 4. (H1) (H1) (H1) (H2) (H2) (H2) (H1) x 4 (H2) x 4 pre-glued dowel assembly screw (H1) #10 x 1-1/2 in. (H2) (H2) (H1) 1. Align dowels on finished surface of bottom panel (G) to the unfinished edge of dividers (F) and (D) as shown. 2.
  • Page 13 step 5. (H2) (H2) (H2) (H2) (H2) (H2) x 6 assembly screw #10 x 1-1/2 in. 1. Align dowels on side panel (A) to the unfinished edge of bottom panel (G) and dividers (C) and (E) as shown. 2. Secure side panel (A) to bottom panel and both dividers using six assembly screws.
  • Page 14 step 6. (H2) (H2) (H2) (H2) (H2) (H2) x 8 assembly screw #10 x 1-1/2 in. (H2) (H2) (H2) 1. Align top panel (B) to the unfinished edge of divider (D) and side panel (A) with the remaining dowels as shown. 2.
  • Page 15 step 7. (H3) (H3) (H3) (H3) (H3) (H3) (H3) (H3) (H3) (H3) (H3) (H3) (H3) (H3) (H3) x 20 screw cover (H3) (H3) (H3) (H3) 1. Push screw covers onto all screw heads. Carefully tap with hammer to secure.
  • Page 16 step 8. warning All units MUST be fastened to the wall. wall top panel stud wall top panel stud (H4) x 1 (H5) x 1 (H6) x 1 L-bracket screw wall screw L-bracket #10 x 1/2 in. flathead #10 x 1-1/2 in. 1.

  • Page 17: Weight Capacity/Care Instructions

    weight capacity/care instructions 15 lbs. warning This unit has been designed for the weight shown. Exceeding this recommended weight could result in excessive "sagging" of the top or shelves. Extreme overloading can cause failure of the unit and possible injury. Care Instructions: Dust with a clean, lint-free dry cloth.
  • Page 18 © 2018 Target. The Bullseye Design is a trademark of Target Brands, Inc. All rights reserved.
Save PDF