Related Manuals for Target 9-Cube
Summary of Contents for Target 9-Cube
- Page 1 9-Cube style dpci finish 58020 002-11-0590 White 58023 002-11-0588 Espresso >> assembly instructions...
-
Page 2: Before You Begin
Congratulations on your latest Target purchase. Now what? Don’t start sweating over this box of parts. This will be easy. We did the hard work for you. All you need to do is follow our simple instructions and you’ll be on your way to transforming your room in no time. - Page 3 table of contents introduction hardware parts list safety precautions helpful hints installing L-bracket assembly 9-18 QUESTIONS? Just call 1-800-874-0008 for parts and service. For faster service, have the style number and DPCI number ready when calling.
-
Page 4: 10 X 1/2 In. Flathead
hardware (H1) x 20 (H2) x 20 (H3) x 2 (H4) x 8 (H5) x 10 assembly screw screw cover hole plug long dowel short dowel #10 x 1-1/2 in. flathead (H6) x 60 (H7) x 1 (H8) x 1 (H9) x 1 nail L-bracket screw... - Page 5 ITEM DESCRIPTION QUANTITY side panel top/bottom panel horizontal divider vertical divider back panel...
-
Page 6: Safety Precautions
safety precautions warning • This unit contains small parts which could be a choking hazard for small children. Children should be under adult supervision at all times or serious injury could occur. • Always unload unit prior to moving the unit. The weight of personal belongings can cause the unit to become unstable and either tip or collapse. Serious bodily injury and/or damage to personal belongings may occur. -
Page 7: Helpful Hints
helpful hints We recommend you protect your work surface during assembly to prevent scratching or damage to table tops, wood floors, etc. finished edge unfinished edge Unfinished edges are shaded in gray. It is important to understand how finished edges go together. Take a moment to lay out all the wood pieces and note the finished and unfinished (raw wood) edges. -
Page 8: Installing L-Bracket
installing L-bracket There are several "key points" to L-bracket installation. Please review the wall Install short end against wall/wall drawings and comments at right as well stud stud; long end against unit. as the assembly steps provided. All units must be fastened to the wall. short Always mount L-bracket to a wall-stud. - Page 9 step 1. (H5) x 4 short dowel 1. Push 4 short dowels into holes of one fixed shelf. 2. Install dowels only into one top/bottom panel (both top/bottom panels are the same.) 3. Top/Bottom panels have six holes on one side with the middle holes going through to the other side. 4.
-
Page 10: Assembly
step 2. (H1) x 2 assembly screw #10 x 1-1/2 in. flathead 1. Attach fixed shelf to one side panel. 2. Make sure finished edges of unit are up. - Page 11 step 3. (H1) x 2 assembly screw #10 x 1-1/2 in. flathead 1. Attach one set of vertical dividers. 2. Push vertical dividers onto dowels in fixed shelf. 3. Make sure finished edges of unit are up. 4. From opposite side of fixed shelf, secure each vertical divider with a screw.
- Page 12 step 4. (H1) x 2 (H4) x 4 assembly screw long dowel #10 x 1-1/2 in. flathead 1. Insert long dowels. 2. Attach horizontal divider. Be sure to assemble with all finished edges to front. 3. Push horizontal divider down over dowels. (Holes in horizontal dividers go all the way through.) 4.
- Page 13 step 5. (H1) x 2 (H4) x 4 assembly screw long dowel #10 x 1-1/2 in. flathead 1. Attach one set of vertical dividers. 2. Insert long dowels. 3. Attach horizontal divider. Be sure to assemble with all finished edges to front. 4.
- Page 14 step 6. (H1) x 4 (H5) x 4 assembly screw short dowel #10 x 1-1/2 in. flathead 1. Insert SHORT dowels and attach top fixed shelf. Be sure to assemble with all finished edges to front. 2. Align holes in underside of top fixed shelf and place top panel into position. 3.
- Page 15 step 7. (H1) x 8 assembly screw #10 x 1-1/2 in. flathead 1. Attach other side panel with provided screws. 2. Be sure to assemble with all finished edges to front.
- Page 16 step 8. (H2) x 20 (H6) x 60 screw cover nail 1. Lay unit so finished (front) edges face down and unfinished edges face up. (Unfinished surfaces are shaded in gray.) 2. Push screw covers onto all screw heads. Gently tap in place with hammer. 3.
- Page 17 step 9. single unit when stacking units (H3) x 2 (H5) x 2 hole plug short dowel 1. Install dowels or hole plugs. 2. For single unit: Insert hole plugs into top holes. 3. For stacking units: Insert dowels into top holes.
- Page 18 step 10. wall stud single unit top panel top panel when stacking units wall stud (H7) x 1 (H8) x 1 (H9) x 1 L-bracket screw wall screw L-bracket #10 x 1/2 in. flathead #10 x 1-1/2 in. 1. Align center of unit with wall stud. (All units MUST be fastened to the wall. When stacking units, the unit on the bottom must be attached to the wall first before setting another unit on top.
- Page 19 weight capacity/care instructions 40 lbs. warning This unit has been designed for the weight shown. Exceeding this recommended weight could result in excessive "sagging" of the top or shelves. Extreme overloading can cause failure of the unit and possible injury. Care Instructions: 15 lbs.
- Page 20 © 2018 Target. The Bullseye Design is a trademark of Target Brands, Inc. All rights reserved.
Need help?
Do you have a question about the 9-Cube and is the answer not in the manual?
Questions and answers