Advertisement
Quick Links
Advertisement
Related Manuals for crystal fires JEWEL SUNRISE
Summary of Contents for crystal fires JEWEL SUNRISE
- Page 1 UNIT 1 VALENTINES BUILDING AINTREE RACECOURSE BUSINESS PARK AINTREE LIVERPOOL L9 5AY JEWEL SUNRISE/PETIT/CUBE DECORATIVE FUEL EFFECT GAS FIRE THIS APPLIANCE IS CAT I FOR USE WITH NATURAL GAS ONLY G20 AT 20mbar IN G.B. AND I.E. USERS INSTALLATION & SERVICING BOOK issue 3...
-
Page 2: Table Of Contents
INDEX FRONT COVER 2.INDEX 3.TECHNICAL DATA 4.INSTALLATION GENERAL 5.HEARTH 6.INSTALLATION 7.FIG A 8. INSTALLATION 9.INSTALLATION /ODS/ SERVICING 12. USERS INSTRUCTIONS 14.FUEL LAYOUT 22.REMOTE INSTRUCTIONS NAME MODEL No GC No SUPER HEATRAVE SUNRISE PLEASE READ THESE INSTRUCTIONS CAREFULLY BEFORE YOU START INSTALLING THE APPLIANCE KEEP THIS BOOKLET HANDY FOR FUTURE REFERENCE issue 3... -
Page 3: Technical Data
......TECHNICAL DATA..... 840mm 760mm SUNRISE 680mm 300mm 607mm CUBE 680mm 300mm 692mm 607mm PETIT 530mm 300mm 692mm SIZES INCLUDING TRIM GAS TYPE: G20 NATURAL GAS PRESSURE : 20 MBAR CONNECTION:8mm OD TUBE SPARK GAP: 2.5-4mm INJECTOR :MANUAL TYPE CAT 82/460 BRAY INJECTOR : REMOTE TYPE CAT 82/440... -
Page 4: Installation General
JEWEL SUNRISE IS DESIGNED AND TESTED TO THE REQUIREMENTS OF BSEN509:2000 AND IS FITTED WITH AN ATMOSPHERE SENSING DEVICE THE JEWEL SUNRISE CAN ONLY BE USED IN CONJUNCTION WITH A CONVENTIONAL CLASS 1 FLUE OR A 5” FLUE LINER WHEN INSTALLED WITH A... -
Page 5: Hearth
SUNRISE /CUBE/PETIT 4 SIDED ADDENDUM SHEET USERS INSTALLATION AND SERVICING INSTRUCTIONS APPLIANCE MUST BE FITTED MINIMUM 300mm TO BOTTOM OF TRIM, FLOOR LEVEL HEARTH NO PURPOSE MADE HEARTH IS REQUIRED WITH THIS GAS APPLIANCE PROVIDING IT IS WALL MOUNTED AT A MINIMUM HEIGHT OF 300mm TO THE BOTTOM OF THE APPLIANCE TRIM... -
Page 6: Installation
A LINED FLUE WITH A MINIMUM DIAMETER OF 175 mm(7ins), OR A LINED FLUE WITH A MINIMUM DIAMETER OF 125mm when used with a crystal fires flue spigot.see fig.a Under no circumstances must a 125 mm liner be used without the... - Page 7 fig a 355mm 160mm 120mm 210mm 407mm PLAN VIEW 60mm 300mm 355mm 40mm front view +/_ 3mm sunrise/cube /petit flue spigot TO SUIT 125mm FLUE LINER CONNECT FLUE LINER TO FLUE SPIGOT AND SECURE.LEAVE IN BUILDERS OPENING 25mm ABOVE TOP OF SUNRISE BOX. INSERT BOX INTO OPENING AND SECURE SPIGOT USING 8 SELFTAPPING SCREWS SUPPLIED.
-
Page 8: Installation
INSTALLATION STEPS CHECK FLUE CHECK THAT THE CHIMNEY CONFORMS TO THE REQUIRED SPECIFICATIONS AS PREVIOUSLY STATED EXAMINE THE CONDITION AND CARRY OUT ANY REMEDIAL WORK IF THE FLUE HAS BEEN USED FOR SOLID FUEL IT SHOULD BE SWEPT AND A SMOKE TEST CARRIED OUT TO CHECK THAT SATISFACTORY SMOKE CLEARANCE HAS BEEN ESTABLISHED IF ALL THE SMOKE IS NOT DRAWN INTO THE FLUE ,PRE HEAT THE FLUE WITH... - Page 9 INSTALLATION STEPS TEST FOR SPILLAGE CHECK FOR SATISFACTORY CLEARANCE OF COMBUSTION PRODUCTS CLOSE ALL DOORS AND WINDOWS IN THE ROOM CONTAINING THE FIRE. TURN ON GAS SUPPLY,LIGHT THE FIRE AND SET THE CONTROLS TO HIGH LEAVE THE FIRE BURNING FOR FIVE MINUTES AND INSERT A LIGHTED SMOKE MATCH ON A VERTICAL PLANE 50mm INSIDE THE CANOPY AND 180mm FROM EITHER SIDE OF THE OPENING...
- Page 10 SERVICING NOTES GENERAL NOTES. SERVICING SHOULD BE CARRIED OUT ANNUALLY BY A COMPETENT PERSON SUCH AS A CORGI REGISTERED PERSON IN ACCORDANCE WITH THE RELEVANT REGULATIONS ,TO ENSURE THE SAFE AND CORRECT OPERATION OF THE APPLIANCE BEFORE COMMENING ANY SERVICE OR REPLACEMENT OF PARTS TURN OFF GAS SUPPLY TO FIRE AFTER SERVICING CHECK FOR GAS SOUNDNESS AT LEAST ONCE A YEAR CHECK FOR DEBRIS...
- Page 11 issue 3...
- Page 12 1 VALENTINES BUILDINGS BECHERS DRIVE AINTREE RACECOURSE BUSINESS PARK AINTREE LIVERPOOL L9 5AY JEWEL SUNRISE/CUBE /PETIT DECORATIVE FUEL EFFECT GAS FIRE THIS APPLIANCE IS CAT I FOR USE WITH NATURAL GAS ONLY G20 AT 20mbar IN G.B. AND I.E. USERS INSTUCTIONS issue 3...
-
Page 13: Users Instructions
USERS INSTRUCTIONS FOR JEWEL GAS APPLIANCE YOUR JEWEL GAS APPLIANCE IS A DECORATIVE LIVE FUEL EFFECT GAS FIRE ,DUE TO ITS NEWNESS THE FIRE MAY GIVE OFF SLIGHT SMELL FOR A SHORT PERIOD AFTER INSTALLATION .THIS IS QUITE NORMAL AND WILL DISAPPEAR AFTER A FEW HOURS OF OPERATION. THE APPLIANCE TO WHICH THESE INSTRUCTIONS APPLY MUST BE INSTALLED BY A COMPETENT PERSON(EG. - Page 14 HEAT INPUT HIGH 6.9Kw LOW 4.1Kw gross JET CAT82/460 BRAY PILOT JEWEL DECORATIVE INSERT CRYSTAL FIRES 7 D BECHERS DRIVE L9 5AY THIS APPLIANCE MUST BE INSTALLED IN ACCORDANCE WITH THE RULES IN FORCE AND USED ONLY IN A SUFFICIENTLY VENTILATED SPACE .CONSULT INSTRUCTIONS BEFORE...
- Page 15 JEWEL GAS FIRE LIGHTING WITH TAPER "D" "D" TO LIGHT WITH TAPER ,PUSH "D" "D" LIGHTED TAPER AS SHOWN WHILST FOLLOWING THE OPERATING "B" "B" INSTRUCTIONS "D" "D" "D" "D" "D" "D" "D" TAPER COAL BED LAYOUT PERIODICALLY SMALL DEPOSITS OF SOOT MAY GATHER ON THE FUEL BED AND BURNER, THIS MUST BE REMOVED BY REMOVING FUEL AND BRUSHING ANY DEPOSITS WITH A SOFT BRUSH AND VACUUMING THE BURNER, THEN REPLACE FUEL USING THE FOLLOWING PROCEDURE.
- Page 16 JEWEL GAS FIRE FUEL BED LAYOUT TOP VIEW MIDDLE FUEL PIECES "D" "D" "D" "D" "B" "B" "B" FUEL "B" PIECES "B" CENTRAL "A" REAR "D" "D" LARGE ROUND "D" "D" FUEL PIECES TOUCHING "A" FUEL FONT PIECE "D" PIECES FLAT SIDE FLA T DOWN...
- Page 17 DRIFTWOOD SET UP FOR SUNRISE/JEWEL/SUPER AND LAGOON. ALL PIECES MARKED UNDERNEATH WITH A LETTER LEFT MAIN MATRIX (A) FITS AT REAR OF BURNER AS SHOWN,BEHIND THE TABS OF MATRIX BRACKET. FRONT BASE (B) FITS AS SHOWN ENSURING BOTTOM IN CHANNEL OF MAIN BURNER WITH CUT OUTS OVER SCREWS FRONT AND BACK ARE ALIGNED WHEN LOCATION POINT...
- Page 18 LEFT DRIFTWOOD PIECE (G),SITS AS SHOWN PIECE G HAS A ROUND CUT OUT TO THE REAR FRONT AND PIECE (D) HAS A LOCATING POINT ,THE CUT OUT FITS ONTO THE LOCATING POINT WITH THE BRANCH RUNNING TO THE REAR AND SLOTTING BETWEEN DRIFTWOOD PIECES (D) &...
- Page 19 LOG SET LAYOUT THE MATRIX FITS BEHIND BRACKETS, AND FRONT FIBRE IN WELL OF FRONT OF THE BURNER ,FLAT (BRCKETS MARKED WITH WHITE DOTS) THE MAIN FRONT LOG CAN NOW BE PUSHED CENTRAL UP TO TWO STOP POINTS ON THE BURNER SITTING ON CARRIER ON LEFT AND RIGHT. ONCE MAIN LOG IS PUSHED UP TO LUGS .THE TWO SIDE LOGS CAN BE PLACED,THESE TWO SIDE LOGS ARE HOLLOW AND ARE FITED ON EACH SIDE OF THE MATRIX.
- Page 20 THE LOG SET REAR CAN NOW BE PLACED ON TOP OF MATRIX CENTRAL BETWEEN THE SIDE LOGS AS SHOWN. THE TWO FIR CONES CAN NOW BE PLACED ON THE MATRIX BETWEEN THE TWO SIDE LOGS AND TOUCHING THE MAIN FRONT LOG.WITH THE POINTS LOOKING OUT AS SHOWN.
- Page 21 THE THREE LARGE ROUND STONES FIT IN THE CENTRE OF THE MATRIX,WITH THE TWO SMALL STONES AT THE SIDES AS SHOWN. THE REAR CURVED LOG CAN NOW BE PLACED TOUCHING THE REAR LOG ON TOP OF THE STONES.CENTRAL THE TWO SIDE LOGS CAN NOW BE PLACED ON TOP OF THE FRONT SMALL LOGS CENTRE,AND ON TOP OF THE HOLLOW LOG AT THE SIDE,WITH THE CURVED BRANCH ALSO JUST TOUCHING AT THE BACK , THE FOUR SMALL LOGS CAN NOW BE PLACED OVER THE CURVED LOG AND THE TWO...
- Page 22 MERTIK MAXITROL REMOTE CONTROL SYSTEM ADDITIONAL INSTRUCTIONS THESE INSTRUCTIONS ARE FOR THE USE ON CRYSTAL FIRES REMOTE CONTROL RANGE OF GAS FIRES ON POSITION OFF POSITION IGNITION /PILOT POSITION FIGURE 1 OPERATION LIGHTING PROCEDURE 1. TURN KNOB A (FIGURE 1) SLIGHTLY LEFT TOWARDS THE IGNITION...
- Page 23 SHUT OFF PROCEDURE 1.TURN KNOB A RIGHT UNTIL REACHING STOP. IN THIS POSITION ONLY PILOT GAS FLOWS 2.TO SHUT OFF VALVE COMPLETELY,PRESS DOWN SLIGHTLY AND CONTINUE TURNING RIGHT FROM PILOT POSITION TO THE OFF POSITION.THE SAFETY INTERLOCK PREVENTS RE-IGNITION OF THE PILOT FLAME UNTIL THERMOCOUPLE HAS COOLED DOWN SUFFICIENTLY(ELAPSED TIME WILL VARY BASED ON THERMOCOUPLE TYPE)
Need help?
Do you have a question about the JEWEL SUNRISE and is the answer not in the manual?
Questions and answers