Table of Contents
Advertisement
Appendix
Aspire Networking Examples
Aspire A
Program 10-12-01
•
IP Address of the NTCPU =
172.16.0.10
Program 10-12-02
•
Subnet Mask = 255.255.0.0
Program 10-12-03
•
Default Gateway = 192.168.1.100
(this is the router's inside address)
The installation site's IT personnel
should be able to provide these IP
addresses.
Program 10-20-01 TCP Port Setup
•
Device 4 = 30000
Program 10-27-01 Destination IP Address
(as entered in Aspire B and C's Program
10-12-01) and port number for each ID
•
ID 1 = IP Address 172.16.0.11
Procedure port must be set to 1730
•
ID 2 = IP Address 172.16.0.12
Procedure port must be set to 1730
Program 11-01-01 System Numbering
•
Dial 2x = 3 digit, Type 2 (Intercom)
•
Dial 3x = 3 digit, Type 8 (Networking),
ID=1
•
Dial 4x = 3 digit, Type 8 (Networking),
ID=2
Program 20-01-04 BLF Refresh Rate
•
BLF Refresh Rate = 30
For Hotline lamping over the network.
Program 84-05-01 (VOIPU card in slot 2)
•
IP Address of the VOIPU PCB =
172.16.0.21
The installation site's IT personnel
should be able to provide these IP
addresses.
Program 84-06-01 VOIPU Setup
•
DTMF Behavior = 2 (Out of Band)
Program 84-12-31 H.323 Phone CODEC
•
DTMF Relay Mode = 1 (RFC2833)
Program 84-02-35 Fast Start
•
Enable Fast Start
244 ◆
Program 10-12-01
•
IP Address of the NTCPU =
172.16.0.11
Program 10-12-02
•
Subnet Mask = 255.255.0.0
Program 10-12-03
•
Default Gateway = 192.168.1.100
(this is the router's inside address)
The installation site's IT personnel
should be able to provide these IP
addresses.
Program 10-20-01 TCP Port Setup
•
Device 4 = 30000
Program 10-27-01 Destination IP Address
(as entered in Aspire A and C's Program
10-12-01) and port number for each ID
•
ID 1 = IP Address 172.16.0.10
Procedure port must be set to 1730
•
ID 2 = IP Address 172.16.0.12
Procedure port must be set to 1730
Program 11-01-01 System Numbering
•
Dial 2x = 3 digit, Type 8 (Networking),
ID=1
•
Dial 3x = 3 digit, Type 2 (Intercom)
•
Dial 4x = 3 digit, Type 8 (Networking),
ID=2
Program 20-01-04 BLF Refresh Rate
•
BLF Refresh Rate = 30
For Hotline lamping over the network.
Program 84-05-01 (VOIPU card in slot 3)
•
IP Address of the VOIPU PCB =
172.16.0.22
The installation site's IT personnel
should be able to provide these IP
addresses.
Program 84-06-01 VOIPU Setup
•
DTMF Behavior = 2 (Out of Band)
Program 84-12-31 H.323 Phone CODEC
•
DTMF Relay Mode = 1 (RFC2833)
Program 84-02-35 Fast Start
•
Enable Fast Start
After programming, each system must be reset in order for the IP address changes to take affect.
VOIPU PCB's
In the example above the VOIPU is in a different slot number in each system. This is only to sim-
plify the example, since at default each slot is assigned a different IP address in Program 84-05-01.
In practice the IP address of the VOIPU PCB will be changed from default to an address within the
customer's network range. Therefore, the VOIPU can be installed into any slot.
Aspire B
Aspire C
Program 10-12-01
•
IP Address of the NTCPU =
172.16.0.12
Program 10-12-02
•
Subnet Mask = 255.255.0.0
Program 10-12-03
•
Default Gateway = 192.168.1.100
(this is the router's inside address)
The installation site's IT personnel
should be able to provide these IP
addresses.
Program 10-20-01 TCP Port Setup
•
Device 4 = 30000
Program 10-27-01 Destination IP Address
(as entered in Aspire A and B's Program
10-12-01) and port number for each ID
•
ID 1 = IP Address 172.16.0.10
Procedure port must be set to 1730
•
ID 2 = IP Address 172.16.0.11
Procedure port must be set to 1730
Program 11-01-01 System Numbering
•
Dial 2x = 3 digit, Type 8 (Networking),
ID=1
•
Dial 3x = 3 digit, Type 8 (Networking),
ID=2
•
Dial 4x = 3 digit, Type 2 (Intercom)
Program 20-01-04 BLF Refresh Rate
•
BLF Refresh Rate = 30
For Hotline lamping over the network.
Program 84-05-01 (VOIPU card in slot 4)
•
IP Address of the VOIPU PCB =
172.16.0.23
The installation site's IT personnel
should be able to provide these IP
addresses.
Program 84-06-01 VOIPU Setup
•
DTMF Behavior = 2 (Out of Band)
Program 84-12-31 H.323 Phone CODEC
•
DTMF Relay Mode = 1 (RFC2833)
Program 84-02-35 Fast Start
•
Enable Fast Start
Networking
Hide quick links:
Advertisement
Table of Contents
