Sealey VS8196.V3 Instructions

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions and maintained properly, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT
CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL
INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to Instruction
Manual
1. SAFETY
IMPORTANT: Failure to understand and follow the instructions listed below may result in electric shock, fire and/or
serious personal injury.
1.1. Work Area Safety
1.1.1. Always perform automotive testing in a safe environment.
1.1.2. Ensure that work area is clean and well lit.
1.1.3. Keep clothing, hair, hands, tools, test equipment, etc. away from all moving or hot engine parts.
1.1.4. Operate the tool in a well-ventilated work area.
1.1.5. DO NOT operate the tool in explosive atmospheres.
1.1.6. Ensure that a suitable fire extinguisher is available.
1.1.7. DO NOT use the tool around corrosive chemicals which can damage the tool.
1.1.8. Keep unauthorised personnel and children clear of the work area whilst operating the tool.
1.1.9. Keep the tool dry, clean, free from oil, water and grease. Use a mild detergent on a clean cloth to clean the outside of the tool when
necessary.
1.2. Battery
1.2.1. Remove the battery while cleaning the tool.
1.2.2. Remove the battery before storing the tool for a long period of time to prevent battery leakage damaging the battery compartment.
1.2.3. When necessary, replace all four batteries with new ones.
1.2.4. Use only the size and type of batteries specified.
1.2.5. Be sure to install the batteries with the correct polarity as indicated in the battery compartment.
1.2.6. Dispose of batteries according to local authority guidelines. DO NOT dispose of batteries in fire.
1.3. Operating Safety
Use the tool only as directed. DO NOT operate the tool unless the instruction manual has been read thoroughly.
1.3.1.
1.3.2. The display unit is not waterproof. The probe head and cable are waterproof, but not acid proof or fireproof. Avoid submersing the probe
head and cable into corrosive, oily places and be sure to keep the probe head and cable away from high temperature objects.
DO NOT immerse the display unit in water.
1.3.3.
1.3.4. DO NOT use excessive force to insert or withdraw the probe head and cable. This may result in damage to the tool or inspection area.
1.3.5. DO NOT use the probe head and cable as a clearing tool.
1.3.6. DO NOT place the probe head and cable into anything or anywhere that may contain a live electric charge or moving parts.
1.3.7. DO NOT use the tool for personal inspection or medical use in any way. This is NOT a medical tool.
1.3.8. DO NOT eat or smoke while operating the tool. Use hot, soapy water to wash hands and other body parts exposed to drain contents after
using the tool to inspect drains and other areas that may contain chemicals or bacteria.
1.3.9. When the inspection is completed, carefully withdraw the probe head and cable from inspection area.
1.3.10. Maintain the tool with care. Properly maintained tools are less likely to cause injury.
1.3.11. DO NOT drop the tool. If the tool is accidently dropped, check for damage.
1.3.12. Always wear appropriate personal protective equipment whilst handling and using the tool. A full range of PPE is available from your
Sealey stockist.
1.3.13. Protect against excessive heat. The tool should be kept away from heat sources. DO NOT use the tool near moving machinery or in areas
where the temperature will exceed 113°F (45°C).
1.3.14 DO NOT over-reach. Maintain proper footing and balance at all times.
1.3.15 DO NOT use the tool while tired or under the influence of drugs, alcohol, or intoxicating medication.
1.3.16. After use, store the tool in a safe, dry, childproof area.
© Jack Sealey Limited
INSTRUCTIONS FOR:
VIDEO BORESCOPE Ø9mm PROBE
VS8196.V3
MODEL No.
Wear Eye
Protection
Original Language Version VS8196.V3 Issue: 1 - 30/03/17