Troubleshooting Codes - Tormax 1102 Installation And Service Manual

Troubleshooting Codes

* E = Error | H = Hint
* No. Fault
E0x Internal test negative. Fatal error.
E11 Motorised lock not unlocked
E12 Motorised lock not locked
E23 CAN connection EDM interrupted
E24 CAN connection PDM interrupted
E25 CAN connection MDM interrupted
E26 CAN connection primary - second. interrupted Primary continues, second. stays closed
E31 Safety open > 1 min. active, test neg.
E32 Safety closing > 1 min. active, test neg.
E33 Safety stop > 1 min. active, test neg.
E34 Safety swing area > 1 min. active, test neg.
E35 Safety open creep > 1 min. active, test neg.
E36 Safety close creep > 1 min. active, test neg.
E37 Safety open Low En. > 1min. active, test neg.
E38 Safety clos. Low En. >1min. active, test neg.
E41 Activator inside > 1min. active
E42 Activator outside > 1min. active
E43 Key switch > 1min. active
E45 Emergency open > 1 min. active
E46 Emergency close > 1 min. active
E47 Inhibit switch > 1 min. active
E48 Activator bed passage > 1min. active
E51 Encoder not working
E61 Power supply 40V outside of admissible range Safety operating mode
E62 Power Supply 24V outside of permissible range Safety op. mode
E63 Power Supply 24V short circuit
E64 Motor hot
E66 Motor faulty. Interruption of motor control.
E68 Power failure (Power on)
E99 Error at secondary drive unit
H01 System was started
H02 Factory reset required (VEE unreadable)
H11 Parameter 06... not yet programmed
H12 Parameter 07... not yet programmed
H13 Parameter 08... not yet programmed
H14 Commissioning not executed
H15 Timeout moving. Door blocked. Motor faulty
H16 Mass detection faulty (wind, opening angle)
H17 Open endstop too soft. Motor may overheat
H18 Safety function is used more than once
H19 Detection of safety functions pending
H21 Teach-In: Door moves >25 s before start
H22 Teach-In: No start within 60s
H23 Teach-In: Movement to slow. >60 s
H31 Obstacle detection at opening
H32 Obstacle detected at closing
H33 Permanent obstacle at opening
H34 Permanent obstacle at closing
H46 FW missmatch in primary and secondary
H62 Calibration run in closing direction
H67 Absolute position not found yet
H71 Battery mode
H74 Motor current in open position too high
Behaviour of System
Safety operating
Door blocked
Safety operating mode
Safety operating mode
Safety operating mode
According safety function
According safety function
According safety function
According safety function
According safety function
According safety function
According safety function
According safety function
Door remains open
Door remains open
Door remains open
Door remains open
Door closes and remains closed
Door closes without hold open time
Door remains open
Safety operating mode
Safety op. mode
Safety operating mode
Safety operating mode. No braking!
Safety op. mode
Safety mode
Safety operation
Safety operation
Safety operation
Safety operation
Commissioning is canceled
Autom. detection is terminated
Abort Teach-In
Abort Teach-In
Abort Teach-In
Door reverses
Door reverses
Safety operation
Safety operation
Searches closed position
Slow opening movement
Door moves slowly
E64 can trigger later
Reset
Power OFF-ON. Possibly press button 5s
Automatically if OK
Automatically if OK
Automatically if OK
Automatically if OK
Automatically if OK
Automatically if OK
Automatically if OK
Automatically if OK
Automatically if OK
Automatically if OK
Automatically if OK
Automatically if OK
Automatically if OK
Automatically if OK
Automatically if OK.
Automatically if OK.
Automatically if OK
Reset
Automatically if OK
Automatically if OK
Automatically after 20s if OK
Automatically after cooling down
Replace motor
Reset
Factory reset
Enter parameter
Enter parameter
Enter parameter
Start commissioning
Restart commissioning
Restart automatic detection
See P60x, P64x, P65x
P023 or OB code 3
New Teach-In
New Teach-In
New Teach-In
Automatically, Display 20s.
Automatically, Display 20s.
Reset
Reset
At the end of movement
Power supply return
P404. Avoid wind load. Install HM
36