Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for KING KX1000
Summary of Contents for KING KX1000
- Page 1 EXTEND KX1000 LTE/CELL SIGNAL BOOSTER User Manual powered by weBoost ®...
-
Page 2: Table Of Contents
BEFORE YOU START Read through this manual before installing or operating the KING Extend. If you have any questions, call KING Customer Service at (952) 345-8147. CONTENTS CONTENTS ....................2 IMPORTANT POINTS ................. 3 COMPONENT LOCATIONS ............... 4 OUTSIDE ANTENNA MOUNTING OPTIONS ..........5 INSTALLATION .................. -
Page 3: Important Points
IMPORTANT POINTS You will need a drill and drill bit, roof-compatible sealant and appropriate fasteners to install all components and wiring. The installer is responsible for determining the most appropriate fasteners to secure the antenna bracket to the roof. Depending on the roof material, fasteners such as lag screws, well nuts, sheet metal screws, toggle bolts and T anchors may be used, and should always be used in combination with a roof-compatible sealant. -
Page 4: Component Locations
COMPONENT LOCATIONS We recommend you do a “soft install” first by placing all components in their chosen locations, completing the setup instructions, and verifying the system works as desired. (Route the cable through an open door or window for the soft install.) NOTE: It is up to the installer to determine the best component locations. The outside antenna must be completely above the roof line. -
Page 5: Outside Antenna Mounting Options
OUTSIDE ANTENNA MOUNTING OPTIONS Page 5... -
Page 6: Installation
INSTALLATION 1. Fasten the outside antenna to the mounting bracket with the supplied screws and washers (see page 5). 2. Connect the separate 20’ cable to the antenna (LARGE CONNECTOR). 3. A pply roof-compatible sealant around the areas where the bracket fasteners will penetrate the roof. 4. Fasten bracket to roof. Make sure fastener holes and fastener heads are properly sealed. - Page 7 5. Route the cable to where it will enter the vehicle. IMPORTANT! Make sure to avoid any cabling, pipes, etc. that may be damaged by drilling. 6. Drill an appropriately sized hole and feed the cable into the vehicle. 7. Seal the roof hole so it is completely waterproof (inside and outside). Fasten cable to roof every 12-18.”...
-
Page 8: Measuring Booster Performance
MEASURING BOOSTER PERFORMANCE Put your cell phone in field test mode and determine the signal inside your vehicle. Note it here: iPhone Dial *3001#12345#* then press Call. ® 1 H old down power button until you see “Slide to Power Off.” 2 Release the power button. 3 Hold the Home button until your main screen appears. If you want to check 3G/1x but your iPhone is picking up 4G/LTE signal , go to Settings>Cellular>Cellular Data Options>Enable LTE>Select Off. - Page 9 (MEASURING BOOSTER PERFORMANCE cont.) All Other Phones and Alternate Methods • https://www.weboost.com/test-mode-instructions/ All Phones: • Keep track of the network (3G or 4G) the phone is connected to. • A ny signal readings you take are valid for that phone’s carrier. To get readings from other carriers, you will need phones from each carrier. • W hen the system is set up, you can easily revert back to the “bar display” by dialing *3001#12345#* and pressing Call.
-
Page 10: Signal Booster Status Light
SIGNAL BOOSTER STATUS LIGHT STATUS LIGHT KC1235 SOLID GREEN This indicates your booster is functioning properly and there are no issues with installation. BLINKING RED, THEN SOLID GREEN This indicates one or more of the booster bands has reduced power due to a feedback loop condition called oscillation. -
Page 11: Troubleshooting
NOTE: Horizontal separation of the two antennas typically requires a shorter separation distance than perpendicular separation. If you are having any difficulties while testing or installing your booster, call KING Customer Service at (952) 345-8147. Page 11... -
Page 12: Specifications
SPECIFICATIONS Product Number U470010 Model Number 460021 FCC ID: PWO460021 4726A-460021 Connectors SMA-Female Antenna Impedance 75 Ohms Frequency 699-716 MHz, 729-756 MHz, 777-786 MHz, 824-894 MHz, 1850-1995 MHz, 1710-1755 MHz/2110-2155 MHz 700 MHz 700 MHz 800 MHz 1700/2100 MHz 1900 MHz Band 12/17 Band 13 Band 5... - Page 13 (SPECIFICATIONS cont.) The term “IC” before the radio certification number only signifies that Industry Canada technical specifications were met. Each signal booster is individually tested and factory set to ensure FCC compliance. The signal booster cannot be adjusted without factory reprogramming or disabling the hardware. The signal booster will amplify, but not alter incoming and outgoing signals in order to increase coverage of authorized frequency bands only. If the signal booster is not in use for five minutes, it will reduce gain until a signal is detected.
-
Page 14: Safety Guidelines
SAFETY GUIDELINES Use only the power supply provided in this package. Use of any other product may damage your equipment. The signal booster unit is designed for use in an indoor, temperature-controlled environment (less than 150 degrees Fahrenheit). It is not intended for use in attics or similar locations subject to temperatures in excess of this range. -
Page 15: Warranty
KING Customer Support at (952) 345-8147. In no event shall KING be liable for any indirect, incidental, or consequential damages from the sale or use of the product. This disclaimer applies both during and after the term of this warranty. - Page 16 Simply better, by design. ™ This product is covered by U.S. patent(s) and pending application(s). For patents go to: weboost.com/us/patents. NOT AFFILIATED WITH WILSON ANTENNA All trademarks are the sole property of their respective owners. © 2019 KING 23525 Rev A...
Need help?
Do you have a question about the KX1000 and is the answer not in the manual?
Questions and answers