Creative Playthings Williamsburg Assembly Manual
  1. Manuals
  2. Brands
  3. Creative Playthings Manuals
  4. Play Sets & Playground Equipment
  5. Williamsburg
  6. Assembly manual

Creative Playthings Williamsburg Assembly Manual

With tent roof
Hide thumbs

Advertisement

Table of Contents

williAMSburg
Model #SH 3200-000
witH tent
ASSeMbly MAnuAl
roof
Please read the owner's manual before assembling your play set.
it provides additional information on the care and use of your play
set. you must carefully read the entire instruction manual before pro-
ceeding with the assembly or use of your new play set.
Creative Playthings takes great care to design its products with
your child's safety in mind. However, only with careful supervision
and proper safety instructions, can you be assured of safe play time
on any product designed for children.
this product is intended for single family home/residential use
only and not intended for use in any public setting. Placement in
any public setting constitutes a misuse of this product.

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Williamsburg and is the answer not in the manual?

Questions and answers

Related Manuals for Creative Playthings Williamsburg

Summary of Contents for Creative Playthings Williamsburg

  • Page 1 Creative Playthings takes great care to design its products with your child’s safety in mind. However, only with careful supervision and proper safety instructions, can you be assured of safe play time on any product designed for children.
  • Page 2 • until assembly is complete, do not let your children use the play set. • never fasten anything not approved by Creative Playthings to your play set. Accessories or items not ap- proved by Creative Playthings include; dog runs, clothes lines, electrical devices, or bird feeders etc.

  • Page 3: Safe Play Area

    • the williamsburg play set has ground dimensions of 8'-3" x 12'-7" (Swing Accessories not included). • the williamsburg play set requires a level ground surface of 21' x 25' for a Safe Play Area (Swing Accessories not included). • Additional accessories may increase the size of the Safe Play Area.

  • Page 4: Hardware Bag Contents

    Weld nut - 1/4”-20 15081-704 1” hole Cap - brown 17001-105 Weld nut - 5/16”-18 12002-205 Flat Washer - 1/4” 50346-700 Hardware bag - williamsburg tent roof 12002-206 Flat Washer - 5/16” 17001-105 Weld nut - 5/16” 12017-205 lock Washer - 1/4” 12002-206 Flat Washer - 5/16”...

  • Page 5: Pre Assembly Information

    Assembly Pre ASSeMbly inforMAtion All hardware on this set is specially coated for corrosion resistance. if non-Creative Playthings hardware is used, it MuSt be galvanized or stainless steel. CreAtiVe PlAytHingS PlAy SetS uSe A few StAndArd ConneCtionS. beCoMing fAMiliAr witH tHeSe ConneCtionS will SiMPlify ASSeMbly And inSure A SAfer PlAy ProduCt for your CHildren.
  • Page 6 Assembly PlAy Set View Williamsburg Page 6 © Copyright 2005, Creative Playthings 19687-100 rev s (10-17)

  • Page 7: Component Parts

    1 ea 50334-700 hardware bag - sP (2005) m* 1 ea 50345-200 hole Cap Pack box 3 - 63006-423 aC 1 ea 40319-400 Williamsburg/Crescent Tent - green 2 ea 32403-102 entrance Wall slat - 5/4 x 6 x 31-1/2" Access ladder box - SH946-102 15 ea 32404-102 Wall slat - 5/4 x 6 x 31-1/2"...

  • Page 8: Maintenance Instructions

    Tighten as required and specified in these instructions. do not over tighten. • Check structure twice monthly during usage for any evidence of deterioration. if upon inspection, hardware has sharp edges, rusted or structural pieces have signs of premature failure; replace them through Creative Playthings Customer service.
  • Page 9 Corner Post. The holes should face the inside of the gym. * note: a hex bolt assembly consists of one hex bolt, one lock Washer, one Flat Washer and one Weld nut. Williamsburg Page 9 © Copyright 2005, Creative Playthings 19687-100 rev s (10-17)
  • Page 10 Platform side in the position as shown in the illustration. do not tighten fasteners completely, they may need to be loosened to install Tent Pipes in a later step. Front back left Williamsburg Page 10 © Copyright 2005, Creative Playthings 19687-100 rev s (10-17)
  • Page 11 Platform end has been omitted from the illustration for clarity. Williamsburg Page 11 © Copyright 2005, Creative Playthings 19687-100 rev s (10-17)
  • Page 12 (W) using four 5/16 x 2-1/2" hex bolt assemblies. do not tighten these bolts yet. The angle braces (b) should be fastened so that the angled end is flat against the nearest Corner Post. Williamsburg Page 12 © Copyright 2005, Creative Playthings 19687-100 rev s (10-17)
  • Page 13 Platform boards (o) on the inside and outside stringers. space the Platform boards (o) evenly between the narrow Platform boards (i). attach each Platform board (o) using six #8 x 2" screws. Williamsburg Page 13 © Copyright 2005, Creative Playthings 19687-100 rev s (10-17)
  • Page 14 Platform ends (W) using four 5/16 x 4" hex bolt assemblies for each support. (one of the end Tent supports will be loosened later when attaching the Tent Poles.) Williamsburg Page 14 © Copyright 2005, Creative Playthings 19687-100 rev s (10-17)
  • Page 15 Wall slats and hand grips on either side of the access ladder. (see steps 24 and 25). Williamsburg Page 15 © Copyright 2005, Creative Playthings 19687-100 rev s (10-17)
  • Page 16 When placing Wall slats, leave no gap larger than 3-1/2" except at entrance or exit points. The right Wall sup- port has been omitted from the illustration for clarity. Williamsburg Page 16 © Copyright 2005, Creative Playthings 19687-100 rev s (10-17)
  • Page 17 2". Fasten the Wall slats using four #8 x 1-5/8" screws. note: When placing Wall slats, leave no gap larger than 3-1/2" except at entrance or exit points. Williamsburg Page 17 © Copyright 2005, Creative Playthings 19687-100 rev s (10-17)
  • Page 18 Fasten the slide using one 1/4 x 3" Truss head bolt and one 1/4" Weld nut for each hole. Williamsburg Page 18 © Copyright 2005, Creative Playthings 19687-100 rev s (10-17)
  • Page 19 1" hole Caps in the hardware bag. install hole Caps into all the counter-bored holes to cover and protect the hardware. illustration #1 Williamsburg Page 19 © Copyright 2005, Creative Playthings 19687-100 rev s (10-17)
  • Page 20 Save all instruction sheets and receipts in case it becomes necessary to con- tact Creative Playthings for warranty service and/or part replacement. the warranty can be found in your owner’s Manual. Please fill out the warranty card on the back of your owners manual. your completed warranty card will allow us to quickly process warranty claims.

This manual is also suitable for:

Williamsburg sh 3100-000

Table of Contents