Related Manuals for Vent-Axia HR200V
Summary of Contents for Vent-Axia HR200V
- Page 1 HR200V Ducted Heat Recovery Ventilator Installation and Maintenance Instructions Stock Ref No:- HR200V 14120010 PLEASE READ INSTRUCTIONS IN CONJUNCTION WITH ILLUSTRATIONS. PLEASE SAVE THESE INSTRUCTIONS ...
- Page 2 INSTALLATION GUIDANCE 1. The installer is responsible for the installation and IMPORTANT SAFETY INFORMATION electrical connection of the sentinel system on site. It is the responsibility of the installer to ensure that the equipment is safely and securely installed and left PLEASE READ THESE only when mechanically and electrically safe.
-
Page 3: Table Of Contents
Warnings & Safety Information Contents Section Page Introduction Site Requirements Installation Electrical Maintenance... -
Page 4: Introduction
1.0 Introduction Description (Fig. 1) Fig. 1 1. The HR200V unit is a void mounting heat recovery ventilator for sealed or internal rooms in domestic, commercial, educational and leisure applications. 2. The HR200V is designed for connection to 150mm diameter standard flexible or rigid ventilation ducting. -
Page 5: Site Requirements
2.0 Site Requirement Information 1. The unit is designed for mounting in a ceiling void and connected to inlet and outlet grilles with 150mm diameter ducting. Dimensions of the unit are shown In Fig.1. 2. Warning: This appliance is class I and it must therefore be earthed. -
Page 6: Installation
Ecotronic 1.5A controller (W300310): Provides variable speed control and on off and auto (sensor) modes. TIM2(370346): The TIM2 is an overrun timer which can also be used to control the HR200V unit via a remote sensor e.g. Humidity Sensor. Fig. 3 Initial Preparation 1. - Page 7 3.0 Installation Fig. 4 Installing the Appliance 1. Offer the mounting frame to the ventilation unit and fix it in position by means of the four machine screws and four of the washers supplied. The washers should be located between the screw heads and the mounting frame.
-
Page 8: Electrical
2. Ensure that the mains power supply is isolated prior to installation. 3. The HR200V is supplied with a length of cable attached from the factory. This can be extended with the use of 4 core cable as required. -
Page 9: Maintenance
4.0 Electrical 5.0 Maintenance Cleaning the Unit 1. In addition to removing odours, providing fresh air and recovering heat, this unit extracts airborne impurities such as dust, dirt and grease. These gradually build up and detract from the efficiency and appearance of the unit. Fig. - Page 10 PRODUCT FICHE For Residential Ventilation Units (Complying Commission Delegated Regulation (EU) No 1254/2014) Name: Vent‐Axia Model ID (Stock Ref.) : HR 200 V ‐ 14120010 SEC Class C SEC Value ('Average') ‐25.44 SEC Value ('Warm') ‐4.28 SEC Value ('Cold') ‐63.16 Label Required? (Yes/No=Out of scope) Yes Declared as: RVU or NRVU/UVU or BVU RVU/BVU Speed Drive Multi‐Speed Type HRS (Recuperative, Regenerative, None) Recuperative Thermal Eff: [ (%), NA(if none)] 70 Max. Flow Rate (m3/h) 198.0 Max. Power Input (W): (@Max.Flow Rate) 110 LWA: Sound Power Level (dB) 66.13 Ref. Flow Rate (m3/s) 0.039 Ref. Pressure Diff. (Pa) 80 SPI [W/(m3/h)] 0.43 Control Factor & Control Typology: (CTRL/ Typology) Control Factor; CTRL 1.00 ...
- Page 12 United Kingdom contact your local supplier. Vent-Axia guarantees its products for two years from date of purchase against faulty material or workmanship. In the event of any part being found to be defective, the product will be repaired, or at the Company’s option replaced, without charge, provided that the product:-...
Need help?
Do you have a question about the HR200V and is the answer not in the manual?
Questions and answers