KSB S 100D Booklet

Submersible borehole pumps 50 hz

Hide thumbs Also See for S 100D:

Installation & operating manual (42 pages)

Booklet (114 pages)

Table Of Contents

100

101

102

103

104

105

106

107

108

109

110

page of 110

/ 110
Contents
Table of Contents
Bookmarks

Table of Contents

Quick Links

Need help?

Do you have a question about the S 100D and is the answer not in the manual?

Questions and answers

Summary of Contents for KSB S 100D

Page 1 3400.5/4--10 G3 Applications Submersible Borehole Pumps -- Drinking and service water supply S 100D, UPA 100C, UPA 150S, UPA 200, -- Irrigation and spray irrigation UPA 200B, UPA 250C, UPA 300, -- Lowering and maintaining ground water levels -- Pressure boosting...
Page 2: Table Of Contents
50 Hz Submersible Borehole Pumps Contents Page The Submersible Borehole Pump Range ........Operation with Soft Starters .
Page 3 -- first rough selection -- on your own to find a suitable KSB submersible borehole pump for your Pump Efficiency application. We have kept the volume of the catalogue down to what we think is the absolute minimum. For the 4 to 14 inch...
Page 4: The Submersible Borehole Pump Range
" UPA 250C (8/10 inch) (8/10 inch) p. 49 -- 57 p. 62 -- 68 " UPA 200B (8/10 inch) p. 58 -- 61 " S 100D " UPA 150S (4 inch) (6 inch) p. 11 -- 22 p. 33 -- 48...
Page 5: Operation With Soft Starters
50 Hz Submersible Borehole Pumps Operation of KSB submersible motor pumps with soft starters Soft starter electronically reduce the incoming line voltage and, Effects on submersible borehole pumps hence, the initial starting torque and starting current of electric -- Starting current ⇒ approx. 40% to 65% of I required for motors.
Page 6: Operation With Frequency Inverter
50 Hz Submersible Borehole Pumps Pump Operation with Frequency Inverter Maximum Operating Frequency In principle, the motors of submersible borehole pumps can also be run on a frequency inverter. As submersible motors Frequency inverter operation above the nominal frequency differ from conventional standardized motors in terms of (50Hz / 60Hz) of the pump unit must be avoided so as to prevent bearings, moment of inertia, insulation, temperature increase, motor overload.
Page 7: Typical Installation Positions
50 Hz Submersible Borehole Pumps Typical Installation Positions Vertical Installation (deep well, pump sump, etc.) CAUTION: The construction of the well head must meet the relevant regulations of the competent authorities! The unit must never be installed with its suction strainer exactly at the level of the well screen / filter! Before installing the unit in narrow deep wells we recommend to check narrow boreholes for dimensional accuracy over their...
Page 8: Submersible Borehole Pump Selection For Deep Wells
50 Hz Submersible Borehole Pumps Submersible Borehole Pump Selection for Deep Wells Pump Selection The following data are required for a first rough selection of a submersible borehole pump: -- Capacity Q in m /h (l/s) -- Pressure at well head H in m -- Well diameter in inches or mm -- Temperature of fluid handled t...
Page 9: Request For Quotation (Form)
50 Hz Submersible Borehole Pumps Request for Quotation We should like to test the efficiency and quality of your computer-aided quotation process. Please let us have a quotation based on the following data. (Fill in the required data and / or underline the relevant information, as far as available.) 1.
Page 10: Head Losses In The Piping
50 Hz Submersible Borehole Pumps Head losses in the piping ft/100 ft m/100 m 3300:103/3-2 The friction losses given in the above chart roughly apply to new diameter reduced by incrustations. For pipes subject to con- cast iron pipes. For new rolled steel or plastic pipes, multiply the siderable incrustation, the friction losses can only be deter- values by approx.
Page 11 E or Cervomatic EDP control and monitoring units, which pro- -- Low noise level tect the pump against dry running, if the water level falls, S 100D -- For vertical, angled or horizontal installation can be used for automatic water supply...
Page 12 50 Hz S 100D n ≈ 2900 rpm Selection Chart (Ranges on Offer) Note: Up to a motor rating of P = 2.2 kW, all pump sizes can be supplied with either single-phase a.c. or three-phase current motors.
Page 13 90 049 385 For cable quality 4 x 1.5 mm up to 4 x 2.5 mm S 100D - 1, 2, 4 + 7: Internal thread G 1’’ (DN 32). S 100D - 12: Internal thread G 2’’ (DN 50).
Page 14 50 Hz S 100D Design Features Easy to commission and service High operating reliability and long service life D Vent valve for operation with automatic D Maintenance--free and wear--protected control units such as Controlmatic E or pump bearings Cervomatic EDP...
Page 15 50 Hz S 100D S 100D - - 1 ... for well diameters of 100 mm (4 inch) Pumps with submersible motors for ... -- Temperature of fluid handled ... .
Page 16 50 Hz S 100D S 100D - - 2 ... for well diameters of 100 mm (4 inch) Pumps with submersible motors for ... -- Temperature of fluid handled ... .
Page 17 50 Hz S 100D S 100D - - 4 ... for well diameters of 100 mm (4 inch) Pumps with submersible motors for ... -- Temperature of fluid handled ... .
Page 18 50 Hz S 100D S 100D - - 7 ... for well diameters of 100 mm (4 inch) Pumps with submersible motors for ... -- Temperature of fluid handled ... .
Page 19 50 Hz S 100D S 100D - - 12 ... for well diameters for 100 mm (4 inch) Pumps with submersible motors for ... -- Temperature of fluid handled ... .
Page 20 50 Hz S 100D Scope of Supply for Single- -phase A.C. Motors DN 100 (1~) A starter for single-phase a.c. motors in PSC design (with integrated run capacitor and motor protection) is included in the scope of supply. Permissible Cable Lengths U up to 3 %, direct starting and t up to + 30 ∆...
Page 21 50 Hz S 100D Accessories: UPA Control for Dry Running Protection (using 3 immersion electrodes) S 100D-1/.. S 100D-1/... Relais Relais Télémécanique Electrode Télémécanique Electrode (Qty.) (Qty.) Ident No. Ident No. 2.5 to 4.0 ( 3 ) 40 980 891 1.0 to 1.6...
Page 22 50 Hz S 100D...
Page 23: Upa 100C
UPA 100C Applications Submersible Borehole Pumps -- Domestic and general water supply for Well Diameters of -- Irrigation and spray irrigation 100 mm (4 inches) -- Lowering ground water levels -- Fountains -- Pressure boosting -- Air-conditioning systems -- Fire protection -- Cooling water cycles Operating Data Maximal capacities...
Page 24 UPA 100C Selection Chart n ≈ 2900 rpm (Ranges on offer) UPA 100C 2 UPA 100C 3 UPA 100C 4 UPA 100C 7 UPA 100C 12...
Page 25: Upa 100C
UPA 100C Materials Drive Type submersible canned motor Component (stainless steel) Connection NEMA standard Enclosure IP 68 Pump ... Frequency f 50 Hz Diffuser Type of current single-phase and three-phase Upper diffuser Rated voltage U 1~ 230 V, Lower diffuser 3~ 400 V, Impeller Rated power P...
Page 26: Upa 100C
UPA 100C Design Features Optimised operating costs: Check valve, built into the dis- Resistance to corrosion and abra- charge chamber, designed for low sion, i.e. the same inherent qualities loss of head. of stainless steel. Hydraulic profiles are optimized for the attainment of high efficiencies.
Page 27: Upa 100C
UPA 100C UPA 100C 2 - - ... UPA 100C 2 - - ... -- 72 (Tolerances to ISO 2548 -- 66 Class C, Annex B) -- 60 -- 54 -- 47 -- 40 -- 35 -- 30 -- 25 -- 21 Ø...
Page 28: Upa 100C
UPA 100C UPA 100C 3 - - ... UPA 100C 3 - - ... -- 68 (Tolerances to ISO 2548 Class C, Annex B) -- 62 -- 57 -- 51 -- 44 -- 36 -- 30 -- 25 -- 22 Ø...
Page 29 UPA 100C UPA 100C 4 - - ... UPA 100C 4 - - ... -- 72 (Tolerances to ISO 2548 Class C, Annex B) -- 66 -- 60 -- 54 -- 50 -- 45 -- 39 -- 34 -- 29 -- 24 Ø...
Page 30 UPA 100C UPA 100C 7 - - ... UPA 100C 7 - - ... (Tolerances to ISO 2548 -- 64 Class C, Annex B) -- 59 -- 54 -- 49 -- 44 -- 39 -- 34 -- 32 -- 29 -- 26 -- 23 Ø...
Page 31 UPA 100C UPA 100C 12 - - ... UPA 100C 12 - - ... (Tolerances to ISO 2548 Class C, Annex B) -- 27 -- 24 -- 20 -- 17 -- 14 -- 13 -- 10 Ø D1 max: -- 8 Pump = 96.5 mm Pump with motor = 98.0 mm...
Page 32 UPA 100C UPA Control Accessory: UPA Control for dry running protection (using 3 immersion electrodes) Relay (A) Ident. No. 1.0 to 1.6 40 980 887 1.6 to 2.5 40 980 889 2.5 to 4.0 40 980 891 4.0 to 6.0 40 980 893 5.5 to 8.0 40 980 895...
Page 33: Pump Sets 6 Inches
50 Hz UPA 150S Applications Submersible Borehole Pumps Suitable for handling clean or slightly contaminated water in for Well Diameters of applications such as: -- for domestic water supply 150 mm (6 inches) -- general water supply -- irrigation and spray irrigation systems -- artificial lowering of the ground water level as well as -- heat transfer plants In addition, the pump sets are used in pressure boosting...
Page 34 50 Hz UPA 150S Selection Charts 2900 rpm (Ranges on Offer) ≈ Note: The operating ranges ∆Q of the individual pump sizes are given in the characteristic curves for different stage numbers on the following pages. The ∆Q operating ranges of the individual pump sizes are given in the characteristic curves for diffrent stage numbers on the following pages.
Page 35 50 Hz UPA 150S Material Variants Type of Installation In general, the pumps are installed vertically. Some models may also be installed horizontally depending on the number of Component (Standard) (Special) stages. Pump Drive Pump shroud / CrNiMo steel 1) 2) Design .
Page 36 50 Hz UPA 150S Design Features All wetted plastic components are approved for drinking water contact Check valve with anti-blockage (BAM valve disc -- Electric cables, seal elements, -- No jamming or tilting. gaskets, etc. are absolutely fit for use -- Spring-loaded design makes for in drinking water applications.
Page 37 50 Hz UPA 150S...
Page 38 50 Hz UPA 150S UPA 150S - - 12 for Well Diameters of 150 mm (6 inches) and above Pumps with submersible motors for ... -- Type of current / voltage ......three-phase (3 µ) / 400 V -- Starting .
Page 39 50 Hz UPA 150S UPA 150S - - 12 / .. Selection UPA 150S - - 12 /.. The pressure losses H in the check valve are not (Tolerances to considered in the pump characteristic curves. ISO 9906 Class 2 / Annex A) For more details and a selection example refer to page 8.
Page 40 50 Hz UPA 150S UPA 150S - - 20 for Well Diameters of 150 mm (6 inches) and above Pumps with submersible motors for ... -- Type of current / voltage ......three-phase (3~) / 400 V -- Starting .
Page 41 50 Hz UPA 150S UPA 150S - - 20 / .. Selection UPA 150S - - 20 /.. The pressure losses H in the check valve are not (Tolerances to considered in the pump characteristic curves. ISO 9906 Class 2 / Annex A) For more details and a selection example refer to page 8.
Page 42 50 Hz UPA 150S UPA 150S - - 34 for Well Diameters of 150 mm (6 inches) and above Pumps with submersible motors for ... -- Type of current / voltage ......three-phase (3~) / 400 V -- Starting .
Page 43 50 Hz UPA 150S UPA 150S - - 34 / .. Selection UPA 150S - - 34 /.. The pressure losses H in the check valve are not considered in the pump characteristic curves. (Tolerances to ISO 9906 Class 2 / Annex A) For more details and a selection example refer to page 8.
Page 44 50 Hz UPA 150S UPA 150S - - 48 for Well Diameters of 150 mm (6 inches) and above Pumps with submersible motors for ... -- Type of current / voltage ......three-phase (3~) / 400 V -- Starting .
Page 45 50 Hz UPA 150S UPA 150S - - 48 / .. Selection UPA 150S - - 48 /.. The pressure losses H in the check valve are not (Tolerances to considered in the pump characteristic curves. ISO 9906 Class 2 / Annex A) For more details and a selection example refer to page 8.
Page 46 50 Hz UPA 150S UPA 150S - - 65 for Well Diameters of 150 mm (6 inches) and above Pumps with submersible motors for... -- Type of current / voltage ......three-phase (3~) / 400 V -- Starting .
Page 47 50 Hz UPA 150S UPA 150S - - 65 / .. Selection UPA 150S - - 65 /.. The pressure losses H in the check valve are not (Tolerances to considered in the pump characteristic curves. ISO 9906 Class 2 / Annex A) For more details and a selection example refer to page 8.
Page 48 50 Hz UPA 150S...
Page 49: Pump Sets 8 Inches/10 Inches
UPA 200, 200B, 250C 50 Hz Applications Submersible Borehole Pumps Handling clean or slightly contaminated water ... -- in general water supply systems, for Well Diameters -- in irrigation and spray irrigation systems, of 200 mm ( 8 inches) -- in pressure boosting systems, and of 250 mm (10 inches) -- in emergency water supply systems, -- in installations for lowering and maintaining ground water...
Page 50 UPA 200, 200B, 250C 50 Hz Selection Chart n ≈ 2900 rpm (Ranges on Offer) UPA 250C- -150 UPA 250C- -120 UPA 200- -14 UPA 200B- -80 UPA 200- -11 UPA 250C- -250 UPA 200B- -130 UPA 250C- -120 UPA 250C- -150 UPA 250C- -250 UPA 200B- -80 UPA 200- -11...
Page 51 UPA 200, 200B, 250C 50 Hz UPA 200 Threaded end Flanged end Material Variants Pump UPA 200 Component (Standard) (Special) Casing Cast iron Bronze (JL1030) (CC480K--GS) Impeller Glass fibre reinforced NORYL (PPO) Diffuser Glass fibre reinforced NORYL (PPO) Shaft Cr steel (1.4021) CrNiMo steel (1.4462) Wear ring CrNiMo steel (1.4401)
Page 52 UPA 200, 200B, 250C 50 Hz UPA 200B, 250C Coating (Standard) Quality ... 2-component high-build coating (epoxy resin base), Material Variants approved for drinking water contact Coating structure Primer and top coat Film thickness .
Page 53 New: Energy-efficient hydraulic systems Integrated sand separator -- High efficiency and low energy -- Tried and tested KSB patent. costs. -- Added protection from abrasive wear for shafts and bearing areas. -- Long service life and high operating reliability.
Page 54 50 Hz UPA 200 UPA 200 – 11 for Well Diameters of 200 mm (8 inches) and above Pumps with submersible motors for ... . . three-phase current (3~) / 400 V / d.o.l. (D) or star-delta (Y-∆) starting Pump + motor Pump Motor...
Page 55 50 Hz UPA 200 UPA 200 - 11 / .. Selection UPA 200 - - 11 /.. The pressure losses H in the check valve are not (Tolerances to considered in the pump characteristic curves. ISO 9906 Class 2) For more details and a selection example refer to page 8.
Page 56 50 Hz UPA 200 UPA 200 - -14 for Well Diameters of 200 mm (8 inches) and above Pumps with submersible motors for ..three-phase current (3~) / 400 V / d.o.l. (D) or star-delta (Y-∆) starting Pump + motor Pump Motor...
Page 57 50 Hz UPA 200 UPA 200 - 14 / .. Selection UPA 200 - - 14 /.. The pressure losses H in the check valve are not (Tolerances to considered in the pump characteristic curves. ISO 9906 Class 2) For more details and a selection example refer to page 8.
Page 58 50 Hz UPA 200B, 250C UPA 200B - - 80 for Well Diameters of 200 mm (8 inches) and above Pumps with submersible motors for ... . three-phase current (3~) / 400 V / d.o.l. (D) or star-delta (Y-∆) starting Pump + motor Pump Motor...
Page 59 50 Hz UPA 200B, 250C UPA 200B - - 80 / .. Selection The characteristic curves shown apply to the UPA 200B - - 80 /.. standard impeller material, i.e. Noryl. (Tolerances to ISO 9906 Class 2) The performance data for the full impeller diameter and impeller diameter “b”...
Page 60 50 Hz UPA 200B, 250C UPA 200B - - 130 for Well Diameters of 200 mm (8 Iinches) and above Pumps with submersible motors for ... . three-phase current (3~) / 400 V / d.o.l. (D) or star-delta (Y-∆) starting Pump + motor Pump Motor...
Page 61 50 Hz UPA 200B, 250C UPA 200B - - 130 / .. Selection UPA 200B - - 130 /.. The characteristic curves shown apply to the (Tolerances to standard impeller material, i.e. Noryl. ISO 9906 Class 2) The performance data for the full impeller diameter for the given number of stages will only be achieved when the impellers are made of Noryl (PPO).
Page 62 50 Hz UPA 200B, 250C UPA 250C - - 120 for Well Diameters of 250 mm (10 inches) and above Pumps with submersible motors for ... . three-phase current (3~) / 400 V / d.o.l. (D) or star-delta (Y-∆) starting Pump + motor Pump Motor...
Page 63 50 Hz UPA 200B, 250C UPA 250C - - 120 / .. Selection The pressure losses H in the check valve are not UPA 250C-120/... considered in the pump characteristic curves. (Tolerances to ISO 9906 Class 2) For more details and a selection example refer to page 8.
Page 64 50 Hz UPA 200B, 250C UPA 250C - -150 for Well Diameters of 250 mm (10 inches) and above Pumps with submersible motors for ... . three-phase current (3~) / 400 V / d.o.l. (D) or star-delta (Y-∆) starting Pump + motor Pump Motor...
Page 65 50 Hz UPA 200B, 250C UPA 250C - - 150 / .. Selection UPA 250C-150/... The pressure losses H in the check valve are not (Tolerances to considered in the pump characteristic curves. ISO 9906 Class 2) For more details and a selection example refer to page 8.
Page 66 50 Hz UPA 200B, 250C UPA 250C - - 250 for Well Diameters of 250 mm (10 inches) and above Pumps with submersible motors for ... . three-phase current (3~) / 400 V / d.o.l. (D) or star-delta (Y-∆) starting Pump + motor Pump Motor...
Page 67 50 Hz UPA 200B, 250C UPA 250C - - 250 / .. Selection UPA 250C - - 250 /.. (Tolerances to The pressure losses H in the check valve are not ISO 9906 Class 2) considered in the pump characteristic curves. For more details and a selection example refer to page 8.
Page 68 50 Hz UPA 200B, 250C...
Page 69: Pump Sets 12 Inches/14 Inches
50 Hz UPA 300, 350 Fields of Application Submersible Borehole Pumps Handling clean or slightly contaminated water in applications for well diameters such as: -- general water supply, of 300 mm (12 inches) and above -- irrigation and spray irrigation, and of 350 mm (14 inches) and above -- pressure boosting, -- lowering and maintaining ground water levels as well as...
Page 70 UPA 300, 350 50 Hz Selection Charts n ≈ 2900 rpm (Ranges on Offer) on request UPA 300-65 UPA 300-65 UPA 300-94 UPA 300-94 UPA 350-128 UPA 350-180 Note: The diagram shows the ∆Q range on offer. The pumps can be offered for any duty point within this range. The ∆Q operating ranges of the individual pump sizes are given in the characteristic curves for diffrent stage numbers on the following pages.
Page 71 50 Hz UPA 300, 350 Material Variants Type of Installation In general, the pumps are installed vertically. Some models may also be installed horizontally, depending on the number of G (Standard) B (Special) C3 (Duplex) stages and motor size. Pump Casing Cast iron Bronze...
Page 72 Wear-resistant mechanical seal -- Long service life and high operating reliability. The KSB motor -- Efficiencies up to 91 %. -- VDE-compliant, i.e. high level of elec- trical safety. -- Designed for max. pump power to protect unit from overloads.
Page 73 50 Hz UPA 300, 350...
Page 74 UPA 300, 350 50 Hz UPA 300 - - 65 for Well Diameters of 300 mm (12 inches) and above Pumps with submersible motors for ... . . three-phase current (3 µ) / 400 V / d.o.l. (D) or star-delta (Y-∆ ) starting Pump + motor Pump Motor...
Page 75 50 Hz UPA 300, 350 UPA 300 - - 65 / .. Selection The pressure losses H in the check valve are not UPA 300 - - 65 / ... considered in the pump characteristic curves. (Tolerances to For more details and a selection example refer to ISO 9906 Class 2) page 8.
Page 76 UPA 300, 350 50 Hz UPA 300 - - 94 for Well Diameters of 300 mm (12 inches) and above Pumps with submersible motors for ... three-phase current (3 µ) / 400 V and d.o.l. (D) or star-delta (Y-∆) starting Pump + motor Pump Motor...
Page 77 50 Hz UPA 300, 350 UPA 300 - - 94 / .. Selection The pressure losses H in the check valve are not UPA 300 - - 94 / ... considered in the pump characteristic curves. (Tolerances to For more details and a selection example refer to ISO 9906 Class 2) page 8.
Page 78 UPA 300, 350 50 Hz UPA 350 - - 128 for Well Diameters of 350 mm (14 inches) and above Pumps with submersible motors for ... . three-phase current (3~) / 400 V and d.o.l. (D) or star-delta (Y-∆) starting Pump + motor Pump Motor...
Page 79 50 Hz UPA 300, 350 UPA 350 - - 128 / .. Selection The pressure losses H in the check valve are not UPA 350 - - 128 / ... considered in the pump characteristic curves. (Tolerances to For more details and a selection example refer to ISO 9906 Class 2) page 8.
Page 80 UPA 300, 350 50 Hz UPA 350 - - 180 for Well Diameters of 350 mm (14 inches) and above Pumps with submersible motors for ... . three-phase current (3~) / 400 V and d.o.l. (D) or star-delta (Y-∆ ) starting Pump + motor Pump Motor...
Page 81 50 Hz UPA 300, 350 UPA 350 - - 180 /.. Larger discharge heads (units with UMA 300D motors) on request. UPA 350 - - 180 / ... (Tolerances to Selection ISO 9906 Class 2) The pressure losses H in the check valve are not considered in the pump characteristic curves.
Page 82 UPA 300, 350 50 Hz...
Page 83 50 Hz BSX - - BSF Applications Submersible Borehole Pumps Handling clean and raw water in applications such as: for Well Diameters of -- general water extraction / supply, 400 mm (16 inches) and above -- irrigation and spray irrigation, -- lowering and maintaining ground water levels in open-cast mines, -- dewatering and gallery drainage in underground mines.
Page 84 BSX - - BSF 50 Hz Selection Chart n ≈ 1450 rpm (Ranges on Offer) U.S.gpm 1000 1400 4000 2000 3000 6000 10000 Imp.g.p.m. 2000 3000 4000 6000 10000 1000 1400 2000 1000 BRY 504 BRZS 535 BRE 555 BSX 463 BSF 586 1000 2000...
Page 85 50 Hz BSX - - BSF Materials Drive Type ..... . . water-filled submersible squirrel-cage motor, 4 poles Type of enclosure .
Page 86 -- All wetted bolts, screws and nuts are made of CrNiMo steel. -- High operating reliability and simplified dismantling. KSB submersible motor -- VDE-compliant, i.e., high level of electrical safety. -- Designed for max. pump power to protect unit from overloads.
Page 87 50 Hz Applications Submersible Borehole Pumps Handling clean and raw water in applications such as: -- general water extraction / supply, for Well Diameters -- irrigation and spray irrigation, of 500 mm (20 inches) and above -- lowering and maintaining ground water levels in open-cast mines, -- dewatering and gallery drainage in underground mines.
Page 88 50 Hz Selection Chart n ≈ 2900 rpm and n ≈ 1450 rpm (Ranges on Offer) U.S.gpm 1000 2000 5000 10000 Imp. g. p. m. 1000 2000 5000 2000 6000 UPZ ... 1500 5000 4000 1000 n = 1450 rpm 3000 2000 1000...
Page 89 Drive Shaft CrNi steel (1.4057) CrNiMo steel (1.4462) KSB submersible squirrel-cage motor, 2 or 4 poles. Three-phase current (3~). For supply voltages up to U = 6600 V. Water-filled Wear ring Aluminium bronze (CuAl10Ni) motor. The water fill lubricates the bearings and cools the CrNiMo steel windings sealed with water-tight insulation material.
Page 90 50 Hz Design Features Enclosed pump bearing Robust wear rings -- No--maintenance design, high wear -- Replaceable wear rings made of resistance. wear- and corrosion-resistant metal. -- For trouble-free long-term operation. -- Protection against wear in the clearance; easy servicing. Stainless steel pump shaft Pump shroud -- Fully protected by impeller hubs and...
Page 91: Typical Tenders: 4 To 14 Inches
Submersible borehole pump(s) type S 100D for well diameters of 100 mm (4 inches) and above Make: Pump + motor: S 100D - - ......
Page 92 Submersible Borehole Pumps 50 Hz Typical Tender UPA 100C Unit price Amount Item Submersible borehole pump(s) type UPA 100C for well diameters of 100 mm (4 inches) and above. Marke: Pump + motor: UPA 100C - - Multistage centrifugal pump for vertical / angled / horizontal installation.
Page 93 50 Hz Submersible Borehole Pumps Typical Tender for UPA 150S Item Unit price Amount Submersible borehole pump(s) type UPA 150S for well diameters of 150 mm (6 inches) and above. Make: Pump + motor: UPA 150S - - Multistage centrifugal pump with shroud for vertical / horizontal installation.
Page 94 Submersible Borehole Pumps 50 Hz Typical Tender UPA 200B / 250C Unit price Amount Item Submersible borehole pump(s) type UPA 200/200B/250C for well diameters of 200 mm (8 inches) and above. Make: Pump + motor: Multistage centrifugal pump in ring-section design for vertical / horizontal installation.
Page 95 50 Hz Submersible Borehole Pumps Typical Tender for UPA 300 / 350 Unit price Amount Item Submersible borehole pump(s) type UPA 300/350 for well diameters of 300 mm (12 inches) and above. Make: Pump + motor: Multistage centrifugal pump in ring-section design for vertical / horizontal installation.
Page 96: Submersible Motors
DN 100, DN150, UMA 150D to 300D of 100 mm (4 inches) and above Sizes / Connection DN 100, DN 150, UMA 150D, UMA 200D: NEMA standard 940.52 UMA 250D, UMA 300D KSB standard 412.53 914.53 Material Variants 160.52 (Material specifications to EN) 550.53...
Page 97 50 Hz Submersible Motors Submersible Motors DN 100 + 150, UMA 150D to 300D: 1~+ 3~, n ≈ 2900 rpm, d.o.l. + Y-∆ η φ Cu ∅ (submerged) Standard Standard 230 V 380 V 400 V d.o.l. Y-∆ Motor size ≈...
Page 98: Accessories
50 Hz Accessories Accessories Description Ident. No. ≈ Electric extension cable , blue, rubber-sheathed cable for submerged Cable operation in drinking water applications, ambient temperatures t ≤ +50 - - Cable kit, 4-core, round, only for pump sets with three-phase current (3~ motors, DN 100, G RD GWT - J - 4G 1.5 (4 x 1.5 mm...
Page 99 50 Hz Accessories Accessories Description Ident. No. ≈ Cable connector, non-separable, including sealing compound, for connecting 1 extension cable to 1 or 2 motor leads - - Size 28 for connecting 1 extension cable to ... 1 motor lead ....-- supplied, but not connected 95 005 106 0.45...
Page 100 50 Hz Accessories Accessories Description Ident. No. ≈ Adapter from threaded end G 1’’ to threaded end G 1’’ ..90 052 823 0.50 Material: CrNiMo steel Mode of supply: sealed and screwed tightly into the pump end. Adapter, threaded end G / Flange DN, PN 10/40 with 2 recesses on flange, 90 spacing...
Page 101 Galvanized steel and CrNiMo steel material variants on request. Stainless steel immersion electrodes 3 electrodes 40 980 055 1 electrode 40 980 056 Stainless steel wire rope for S 100D 15 m 42 200 727 30 m 42 204 021 Lightning protection with earthing terminal for -- 1~/ 230 V (fitted in soft starter of DN 100 motor) .
Page 102 50 Hz Accessories Electric Cable for Use in Drinking Water Applications Applications For use in water as submersible motor lead (3- + 4-core, flat) and for use in air as extension cable from motor lead to control box / mains (3-core, flat and 4-core, round). Application Limits Rated voltage: -- U...
Page 103 50 Hz Accessories Maximum Permissible Rated Motor Current I a) Ambient temperature t ≤ + 30 in A for cross-section of ... mm Starting Used as ... D.o.l. Motor lead (1 cable (1 cable Extension cable 2 cables in parallel Y-∆...
Page 104 50 Hz Accessories Permissible Cable Lengths L D.O.L. Starting (1 cable or 2 cables in parallel) U = 400 V / ∆U = 3 % / t ≤ + 30 in air = 250 A 70 mm laid along a surface! = 202 A 50 mm = 162 A...
Page 105 50 Hz Accessories Permissible Cable Lengths L Y-∆ Starting (2 cables) = 433 A 70 mm U = 400 V / ∆U = 3 % / = 350 A 50 mm t ≤ + 30 in air = 280 A 35 mm laid along a surface! = 227 A...
Page 106 50 Hz Accessories Connector for Electric Cable Applications Used to provide a sealed, water--tight connection between electric extension cable and submersible motor lead. Supply voltage ... U ≤ 750 V. Ambient temperature .
Page 107 50 Hz Accessories Cable Tie for Electric Cable Applications Securing electric cable at the riser / discharge pipe. Suitable for use in normal or slightly aggressive water. Models for use in more aggressive wasser (for ex. seawater) available on request. Selection Criteria Type, number and size of the electric cable, as well as nominal diameter and length of the riser / discharge pipe.
Page 108: Flow Velocity "V" Past The Motor
50 Hz Submersible borehole pumps Flow Velocity v Past the UMA Submersible Motor Depending on the general installation arrangement (i.e. depending, for example, on the ratio of outside motor diameter to inside well or shroud diameter, etc.) a distinction must be made between the following cases ... a) v = 0 m/s ...
Page 109 50 Hz Submersible borehole pumps...
Page 110 50 Hz Submersible borehole pumps...

This manual is also suitable for:

Upa 200b Upa 100c Upa 150s Upa 200 Upa 250c Upa 350 ... Show all