Rain Bird ESP-ME3 User Manual
Hide thumbs
Also See for ESP-ME3:
- Quick reference manual (2 pages) ,
- Advanced user's manual (19 pages) ,
- User manual
Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Rain Bird ESP-ME3
Summary of Contents for Rain Bird ESP-ME3
- Page 1 Rain+Birdt ESP-ME3 Controller User Manual Ready...
-
Page 2: Table Of Contents
Odd or Even Calendar Days ........12 Technical Support Cyclic Days ..............12 Questions? Seasonal Adjust ............13 Call Rain Bird toll free Technical Support at Delay Watering ............13 1-800-724-6247 (USA and Canada only) Permanent Days Off ........... 13 Special Features..........14 Options ............14... -
Page 3: Introduction
The LNK WiFi Module allows remote connection to Welcome to Rain Bird a Rain Bird ESP-ME3 Controller using an Apple iOS or Android compatible smart device. The mobile applica- Thank you for choosing Rain Bird’s ESP-ME3 controller. tion allows remote access and configuration of one or In this manual are step by step instructions for how to more irrigation controllers. -
Page 4: Installation
VT MV COM 5 6 7 11 12 13 17 18 19 1 2 3 4 8 9 10 14 15 16 20 21 22 VT MV COM 1 2 3 4 VALVE TEST CONNECT 120 VAC SENS MASTER VALVE ESP-ME3 Controller... -
Page 5: Connect Pump Start Relay (Optional)
(+) terminal and the negative (sometimes black) NOTICE sensor wire to the grey (-) terminal. The ESP-ME3 controller DOES NOT provide power for a pump. The relay must be wired according to manufacturer instructions. Only the following Rain Bird pump start relay models... -
Page 6: Connect Weather Sensor (Optional)
8 9 10 14 15 16 20 21 22 power wiring VT MV COM NOTE: Rain Bird ESP-ME3 controllers are only compatible with normally closed rain sensors. 1 2 3 4 VA LV E T E S T C ON NE CT... -
Page 7: Station Expansion Modules
OFF before connecting power wires. NOTE: 6-Station Modules are compatible with POWER WIRING CONNECTIONS ESP-ME3 and ESP-Me. They are not backwards compatible with the ESP-M vintage controller. Black supply wire (hot) to the black transformer wire NOTE: For ideal station sequencing, insert 3-Sta- White supply wire (neutral) to the white transformer wire tion module after inserting all 6-station modules. -
Page 8: Station Numbering
5% up to 200% – / + Buttons Back/Next Run Times Weather Sensors Water Days Adjust feature Buttons Set station Set controller to settings Select days to Select Run Times obey or ignore a allow watering programming weather sensor options ESP-ME3 Controller... -
Page 9: Auto
Soak time between watering S O A K SOAK times - supported through the Rain Bird app. A · B · C · D Hold to Start Advance Station Turn the dial to OFF to stop automatic irrigation or to cancel all active watering immediately. -
Page 10: Basic Programming
Run Time to zero. NOTE: Rain Bird recommends that the maximum irrigation station cycle time be less than the time required for runoff to begin and that there be adequate soak time before the next irrigation cycle of that same station begins again. -
Page 11: Program-Based Scheduling
Manual Watering Options Program-Based Scheduling The ESP-ME3 uses a programmed-based scheduling Test All Stations method to create irrigation schedules. This means all Start watering immediately for all programmed stations with a run time on the program will run in stations. -
Page 12: Run A Single Program
Press Program Select to choose the desired program (if necessary). Press the Hold to Start button to begin watering the selected program. NOTE: See Special Features to set Rain Sensor ON by Station. Turn the dial to AUTO ESP-ME3 Controller... -
Page 13: Seasonal Adjust
DAYS REMAINING. The NEXT watering day will update on the display to indicate when watering will resume. To cancel a Rain Delay, set the DAYS REMAINING back to 0. NOTE: When the delay expires, automatic irriga- tion resumes as scheduled. ESP-ME3 Controller... -
Page 14: Special Features
Options Remote Accessories A 5 pin accessory port is available for Rain Bird Reset Button approved external devices, including: If the controller is not working properly, you can try • LNK WiFi Module pressing RESET. -
Page 15: Detached Programming
Remove the front panel. condition is detected. Install a 9V battery in the battery compartment. The ALARM LED light on the ESP-ME3 controller front panel will light up to indicate an alarm condition: Program the controller. Programming Errors (blinking LED) -
Page 16: Flow Alarms
Low Flow Condition NOTE: Turning the flow sensor feature off and When a flow sensor is in use the ESP-ME3 monitors for then back on will cause the controller to learn High Flow of 130% above regular learned flow. This... -
Page 17: Electrical Issues (Solid Led Illuminated)
LED is flashing or solidly illu- Dial not in AUTO RUN position. Turn dial to AUTO RUN position. Push Reset button or power cycle the controller. minated but I see no message on the LCD. ESP-ME3 Controller... - Page 18 Rain Bird could void the user’s au- All electrical connections and wiring runs must • Reorient or relocate the receiving antenna.
- Page 19 The Intelligent Use of Water® LEADERSHIP · EDUCATION · PARTNERSHIPS · PRODUCTS At Rain Bird, we believe it is our responsibility to develop products and technologies that use water efficiently. Our commitment also extends to education, training and services for our industry and community.
Need help?
Do you have a question about the ESP-ME3 and is the answer not in the manual?
Questions and answers
How do I hook up my system to my smart home
To connect your Rain Bird ESP-ME3 system to your smart home, follow these steps:
1. Download the latest Rain Bird mobile app from the App Store or Google Play.
2. Insert the LNK Wi-Fi module into the accessory port of your ESP-ME3 controller.
3. The module’s light should blink red and green, indicating it is broadcasting a Wi-Fi hotspot.
4. On your smartphone or tablet, open the Wi-Fi settings and connect to the network with "Rainbird" in the name.
5. Follow the app instructions to complete the setup and connect the controller to your home Wi-Fi network.
Ensure the controller has a strong Wi-Fi signal. If the signal is weak, move the router or controller closer or use a Wi-Fi booster.
This answer is automatically generated