Kenwood TK-7180H Service Manual page 9

TK-7180H/7182H
7. Clone Mode
Programming data can be transferred from one trans-
ceiver to another by connecting them via their 8-pin micro-
phone connectors. The operation is as follows (the transmit
transceiver is the master and the receive transceiver is a
slave).
The following data cannot be cloned.
• Tuning data
• Embedded message with password
• Model name data
• ESN (Electronic Serial Number) data
1. Press and hold the [B] key while turning the transceiver
power ON. If the read authorization password is set to the
transceiver, "CLONE LOCK" (TK-7180H) or "CLN LOCK"
(TK-7182H) is displayed. If the password is not set,
"CLONE MODE" (TK-7180H) or "CLONE" (TK-7182H) is
displayed.
2. When you enter the correct password, and "CLONE
MODE" (TK-7180H) or "CLONE" (TK-7182H) is displayed,
the transceiver can be used as the cloning master. The
following describes how to enter the password.
3.
• How to enter the password with the microphone keypad;
If one of keys 0 to 9 is pressed while "CLONE LOCK" (TK-
7180H) or "CLN LOCK" (TK-7182H) is displayed, the
pressed number is displayed on the LCD. Each press of
the key shifts the display in order to the left. When you
enter the password and press the [
MODE" (TK-7180H) or "CLONE" (TK-7182H) is displayed
if the entered password is correct. If the password is in-
correct, "CLONE LOCK" (TK-7180H) or "CLN LOCK" (TK-
7182H) is redisplayed.
• How to enter the password with the [ ] and [ ] keys;
If the [ ] and [ ] keys is pressed while "CLONE LOCK"
(TK-7180H) or "CLN LOCK" (TK-7182H) is displayed, the
number (0 to 9) blinks on the LCD. When you press the [C]
key, the currently selected number is determined. If you
press the [A] key, the least digit of the password is de-
leted. If you press the [S] key after entering the password
in this procedure, "CLONE MODE" (TK-7180H) or
"CLONE" (TK-7182H) is displayed if the entered pass-
word is correct. If the password is incorrect, "CLONE
LOCK" (TK-7180H) or "CLN LOCK" (TK-7182H) is
redisplayed.
4. Power on the slave transceiver.
5. Connect the cloning cable (Part No. E30-3382-05) to the
modular microphone jacks on the master and slave.
6. Press the [S] key on the master while the master displays
"CLONE MODE" (TK-7180H) or "CLONE" (TK-7182H).
The data of the master is sent to the slave. While the
slave is receiving the data, "PROGRAM" is displayed.
When cloning of data is completed, the master displays
"END", and the slave automatically operates in the User
mode. The slave can then be operated by the same pro-
gram as the master.
8
REALIGNMENT
7. The other slave can be continuously cloned. When the [S]
Notes:
• Only the same models can be cloned together.
• Cannot be cloned if the overwrite password is pro-
8. Firmware Version Information
power ON and then keep pressing and holding the [
] key, "CLONE
*
the firmware version information appears on the LCD.
9. Clock Adjustment Mode (TK-7180H only)
9-1. Flow chart of operation
key on the master is pressed while the master displays
"END", the master displays "CLONE MODE" (TK-7180H)
or "CLONE" (TK-7182H). Carry out the operation in step 4
to 6.
grammed to the slave.
Cloning cable
(E30-3382-05)
Fig. 2
Press and hold the [ ] key while turning the transceiver
[C] + Power ON
[ ] and [ ] keys
YEAR
[S]
MONTH [ ] and [ ] keys
[S]
[ ] and [ ] keys
DAY
[S]
HOUR [ ] and [ ] keys
[S]
[ ] and [ ] keys
MINUTE
[S]
Completion
] key,