INVISIBLE FENCE Indoor Shields Plus Owner's Manual
Hide thumbs
Also See for Indoor Shields Plus:
- Owner's manual (10 pages) ,
- Owner's manual (14 pages) ,
- Manual (12 pages)
Related Manuals for INVISIBLE FENCE Indoor Shields Plus
Summary of Contents for INVISIBLE FENCE Indoor Shields Plus
- Page 1 ...
-
Page 2: Important Precautions
• Not every pet can be trained to avoid the established boundary. Sometimes even a properly trained pet may cross the boundary. Therefore, Invisible Fence, Inc., as well as Invisible ® Fence Brand Distributors and Dealers cannot guarantee the system will, in all cases, keep a customer’s pet within the established boundary. - Page 3 ® • Read and follow the important tips on how to avoid pressure necrosis in your Invisible Fence ® Brand Computer Collar unit manual. ® • Train your pet according to the instructions in the Invisible Fence Brand training manuals.
-
Page 4: Table Of Contents
Test the Signal Field……………………………………………………………………………………8 Multi-Area Avoidance .....................9 Programming the Computer Collar® Unit ...............9 Training Guide ........................10 For Pets trained to the Invisible Fence® Brand Outdoor Pet Containment System ....................10 For Pets New to Invisible Fence® Brand ..............10 Troubleshooting ..........................11 Battery Disposal ..........................12... -
Page 5: Components
Components ... -
Page 6: Operating Guide
Operating Guide Important: To ensure your pet does not receive an unintended correction, make sure your pet is ® ® not wearing the Computer Collar unit when turning ON or adjusting the Indoor Shields Plus transmitter. ® 1. -
Page 7: Adjust Signal Field Range
Wireless Option Adjust signal field range • Determine the desired location and the signal field range required. -Wireless: 1.5 ft. minimum radius up to 6 ft. maximum radius. • With the unit ON, press the RANGE UP (+) or the RANGE DOWN (-) buttons to increase or decrease the signal field range. -
Page 8: Signal Field Wire Preparation
You can create a signal field using up to 150 feet of boundary wire (14 – 20 gauge). The recommended ® wire can be purchased from your local Invisible Fence Brand dealer. Visit www.invisiblefence.com to find an authorized dealer in your area. -
Page 9: Multi-Area Avoidance
beeping will be accompanied by a correction. ® • If the Computer Collar Unit fails to beep, see the Troubleshooting chart found on page 11. •Adjust the signal field range and boundary wire position until the desired area is covered. 4. - Page 10 Press and hold the PROGRAM button while lowering the Computer Collar® unit from directly above the Indoor Shields® Plus transmitter. Stop lowering when the Computer Collar® unit begins to flicker yellow and release the PROGRAM button when the Computer Collar® unit begins to flash green.
-
Page 11: Training Guide
Training Guide ® For pets trained to the Invisible Fence Brand system ® • Use Invisible Fence Brand training flags to mark the outside of the signal field range. This gives your pet a visual marker, similar to how they learned the signal field range of the outdoor pet containment system. -
Page 12: Troubleshooting
Plus transmitter CHANNEL setting. See Multi-Area Avoidance warning beep Section on page 9. ® Need additional help? Contact your local Invisible Fence Brand dealer. Call 1-800-578-3647 or visit www.InvisibleFence.com to find your local dealer. 12 ... -
Page 13: Battery Disposal
If you no longer require this equipment, do not place it in the normal municipal waste system. Please return it to where it was purchased in order that it can be placed in ® our recycling system. If this is not possible, please contact your Invisible Fence Brand dealer. ... -
Page 14: Compliance
Compliance US and Canada FCC ID: KE3-3002769 IC: 2721A-3002769 This device complies with Industry Canada rules. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. - Page 15 800-578-3647 (USA) (865) 777-5404 (International) 400-XXXX-X ©2013 Radio System Corporation All rights reserved. Protected by Patents: U.S.: 7,046,152; 7,068,174; 7,204,204; www.InvisibleFence.com...
Need help?
Do you have a question about the Indoor Shields Plus and is the answer not in the manual?
Questions and answers
My invisible fence collar doesn't seem to be working with the indoor shield. I tested it with the A, B, and A+B channel but it doesn't work. I have no issues with my invisible fence collar and my outdoor shields that I own. How do I program the collar correctly with this indoor shield?
To program the INVISIBLE FENCE Indoor Shields® Plus with your Computer Collar® unit, follow these steps:
1. Remove the Collar – Ensure all Computer Collar® units are removed from pets and are at least 3 feet away from the Indoor Shields® Plus transmitter.
2. Select Channel – Follow the procedure to set the Indoor Shields® Plus transmitter to Channel A or B. The transmitter will not enter programming mode if set to A+B.
3. Position the Collar – Press and hold the PROGRAM button on the transmitter while lowering the Computer Collar® unit directly above it.
4. Observe the Indicator Light – Stop lowering when the Computer Collar® unit flickers yellow.
5. Release the Button – Release the PROGRAM button when the Computer Collar® unit begins to flash green.
6. Confirm Programming – The Computer Collar® unit is now programmed to the selected channel. Turn ON the Indoor Shields® Plus transmitter and listen for activation to verify proper operation.
Make sure any collar is programmed correctly before using the system.
This answer is automatically generated