Advertisement
Mounting the Bracket and the Camera
1.
Using the included template as a guide, make a hole (φ 170 mm
[6 11/16 inches]) in the ceiling.
2.
Drive an anchor bolt (not included) into the original ceiling and attach a
nut (not included) to the bolt.
• Drive the anchor bolt into the original ceiling directly above the center of
the hole made in step 1.
• The end of the anchor bolt should be 38 mm (1 1/2 inches) above the
bottom of the ceiling board.
• The bottom of the nut should be 52 mm (2 1/16 inches) above the
bottom of the ceiling board.
Anchor bolt
Nut
Ceiling board
Bolt is above center of hole
3.
Secure the safety wire to the bracket using screw C (included).
(Recommended torque 0.2~0.4 N·m {2.039~4.079 kgf·cm})
4.
Insert the bracket into the hole.
• The camera will face the direction indicated by the arrow on the bracket.
5.
Tighten the 3 clamp screws (attached to the bracket) and secure the
bracket.
1 The clamps tighten as the screws are tightened.
(Recommended torque 0.2~0.4 N·m {2.039~4.079 kgf·cm})
Screws
2 Secure the bracket by attaching and tightening a nut (not included) to
the anchor bolt.
6.
Secure the safety wire (included with the camera) to the camera using
screw B (included with the camera) and washer B (included with the
camera).
• Make sure you attach the safety wire when mounting the camera to
prevent the camera from falling.
(Recommended torque 0.2~0.4 N·m {2.039~4.079 kgf·cm})
Screw B
(Length: 10 mm [3/8 inches],
Body diameter: 2.6 mm [1/8 inches])
Washer B
(Inside diameter: 2.6 mm [1/8 inches])
Template
38 mm
52 mm (2 1/16 inches)
(1 1/2
inches)
Screw C
Safety wire
Clamp screw
Clamp
Ceiling board
Clockwise
Anchor bolt
Nut
Safety wire
Safety wire hole
7.
Pass the necessary cables (AC adaptor, LAN, etc.) through the whole in
the dust protection sheet, and attach the sheet to the bracket slits in 3
places.
• The size of each slit is different. Match the size of the slits with the sheet
notches, and insert the sheet.
Dust Protection
Sheet
Notch
Slit
8.
Secure the camera with the screw D (included with the camera) in 3
places.
• Attach the camera so the " " mark on the unit is aligned with the arrows
on the bracket.
9. 1 Attach the unit's cover by aligning the cover and the microphone of the
unit, and tighten the screws in 3 places.
2 Close the screw covers.
(Recommended torque 0.2~0.4 N·m {2.039~4.079 kgf·cm})
10. Secure the ceiling mounting cover (included) to the bracket.
1 Pass the safety wire through the ceiling mounting cover as shown.
2 Align the " " marks on the rear of the camera and on the mounting
cover.
3 Turn the ceiling mounting cover clockwise until the " " mark on the rear
of the camera and the " " mark on the ceiling mounting cover are
aligned as shown.
• Be careful not to nip the cables, cords, etc.
• To remove the ceiling mounting cover, turn it counterclockwise until the
" " mark on the rear of the camera and on the ceiling mounting cover
are aligned, then lower the ceiling mounting cover.
11. Secure the safety wire to the ceiling.
• Secure the bracket's safety wire first, using screw A and the washer
(included with the bracket), then secure the camera's safety wire, using
screw A and washer A (both included with the camera).
• Secure the safety wires to the ceiling about 160 mm (6 5/16 inches)
from the center of the camera.
• Do not drive the screws into a soft material. Drive the screws into a
secure, 25 mm (1 inch) thick area of the ceiling, such as a crossbeam,
otherwise the bracket and the camera may fall. If there is no
crossbeam, place a board on the other side of the ceiling to make sure
the bracket and the camera are securely mounted.
• Attach the safety wire in a position so that if the camera were to become
detached, it would not fall on nearby people.
Washer
(Inside diameter:
4.0 mm [3/16 inches])
Screw A
(Length: 20 mm [13/16 inches],
Body diameter: 4.0 mm [3/16 inches])
Specifications
Operating temperature +0 °C (+32 °F) to +40 °C (+104 °F)
Dimension (W×H×D)
About 204 mm (8 1/16 inches) × 77.5 mm
(3 1/16 inches) × 204 mm (8 1/16 inches)
Weight
About 635 g (1.40 lb)
Screw D
" " mark
arrow
Screw covers
Washer A
(Inside diameter: 4.0 mm [3/16 inches])
Screw A
(Length: 20 mm [13/16 inches],
Body diameter: 4.0 mm [3/16 inches])
Cables
Advertisement
