Panasonic AK-HRP200G Operating Instructions Manual page 24

Parts and their functions (when operating a remote camera)
32.
SHUTTER DISPLAY SELECT button <SHUTTER>
EXECUTE button <EXECUTE> (In setup mode)
Press this button to display and change the SHUTTER settings.
<Note>
When the Shutter On/Off button <SHUTTER ON> is set to Off, the
SHUTTER DISPLAY SELECT button <SHUTTER> can be operated
and the SHUTTER can be adjusted. (Adjustments can be made prior
to operation.)
z Setting and displaying the SHUTTER
Press and hold the STEP/SYNC select button <STEP/SYNC> for
about 2 seconds to switch between the STEP and SYNC settings.
When SYNCHRO is selected, the SYNCHRO display lights green.
1) Press <SHUTTER> when IRIS display or another (ND/CC,
M.GAIN/M.PED) display is selected.
When STEP is selected, the SHUTTER setting is displayed on
the setting display. (It is not displayed when SYNC is selected.)
2) Press the lit DATA SET button <UP><DOWN>.
This allows you to change the SHUTTER setting. (It cannot be
changed when SYNC is selected.)
3) Press <SHUTTER> again.
The button turns off and the SHUTTER display <SHT> turns off.
Then the setting display returns to IRIS indication.
Pressing another DISPLAY SELECT button (<ND/CC> or
<M.GAIN/M.PED>) turns off the button and lights the selected
button.
<Note>
This cannot be used with the AW-HE2.
In setup mode, this button confirms menus and setting values.
For details on setup mode, refer to Operations and Settings on the
supplied CD-ROM.
33.
SHUTTER display <SHT>
This display is lit green when a SHUTTER setting is displayed on the
setting display.
<Note>
• Press and hold the STEP/SYNC select button <STEP/SYNC> for
about 2 seconds to switch between the STEP and SYNC settings.
When SYNCHRO is selected, the SYNCHRO display <SYNC>
lights green.
• This cannot be used with the AW-HE2.
34.
SYNCHRO display <SYNC>
This display is lit green when a SHUTTER (SYNC) setting is
displayed on the setting display. When STEP indication, this display
is off.
Off: SHUTTER is in STEP mode.
On: SHUTTER is in SYNCHRO mode.
<Note>
• Press and hold the STEP/SYNC select button for about 2 seconds
to switch between the STEP and SYNCHRO settings.
• This cannot be used with the AW-HE2.
35.
Camera number tens' place digit display <10 to 19>
This LED lights when the camera number is between 10 and 19.
Off: The camera number is between 1 and 9.
On: The camera number is between 10 and 19.
The number is between 20 and 22 (when in setup mode
Flashing:
only).
36.
Camera number display <No.>
This display indicates the camera number or the menu number in
setup mode. Only the ones place will be displayed for numbers 10
to 19 and 20 to 22. The tens digit is indicated by the camera number
tens digit display. (It is lit when the camera number tens digit display
is between 10 and 19 and flashing when it is between 20 and 22.)
24
(continued)
37.
Camera select button <SELECT>
Use this button to select the control target camera.
z Selecting the control target camera
A camera connected to the unit can be selected and then
controlled.
1) Press and hold the camera select button <SELECT> for
about 2 seconds.
The camera number in the camera number display flashes.
2) Press the lit DATA SET button <UP><DOWN>.
Press the lit DATA SET button <UP><DOWN> to select a
camera number.
3) Press the camera select button <SELECT>.
Control of the selected camera becomes possible.
<Note>
If the camera select button continues to flash when a camera is
selected by pressing the camera select button, a connection has not
been established. Check the settings of the camera assigned to the
camera number.