Advertisement
Advertisement
Table of Contents
Related Manuals for Power-Pole PRO II Series
Summary of Contents for Power-Pole PRO II Series
- Page 1 INSTALLATION & OWNER GUIDE...
- Page 2 Welcome to the world of Power-Pole ® the original shallow water anchor.
-
Page 3: Installation Tools
Please read all installation instructions carefully. The information contained here describes the proper procedures for safely installing your Power-Pole shallow water anchor. If you have questions, contact our Technical Support Team at 1+ (813) 689-9932 option 2 or visit our website at www.power-pole.com. -
Page 4: Choose A Mounting Location
2. While holding the Power-Pole anchor in place, turn and tilt the motor as far as possible toward the unit. With the motor turned toward the unit, manually move the anchor through its entire range of motion to verify clearance. - Page 5 STEP Installing The Hydraulic Pump Unit (HPU) 1. Locate a dry compartment in the vessel with ample space to accommodate the HPU. The footprint of the HPU is approximately 6.5”x 7”. NOTE: Be sure to allow enough clearance surrounding the HPU to install the (2) 3/8”...
- Page 6 STEP Installing The Hydraulic Hose WARNING: Keep debris out of the hydraulic hose. Do not remove blue plastic from the end of hydraulic hose while routing throughout the boat. Debris in the hose will cause damage to the HPU. OVER THE TRANSOM 1.
- Page 7 Repeat this step once. 9. With the Power-Pole anchor in the retracted state, manually apply a force to attempt to deploy the Power- Pole anchor. If the Power-Pole anchor does not stay in the retracted state, repeat step 8 until it does.
- Page 8 Programming Dual Units UP button NOTE: Each Power-Pole anchor is preprogrammed as a single unit. When using only one anchor do not program as a port or starboard. 1. Determine which HPU controls the starboard side Power-Pole anchor DOWN button using the UP &...
- Page 9 Pairing Dual Units To A Single Wireless Controller PROGRAM button NOTE: Each Power-Pole anchor comes paired to the included Dash Switch and Key Fob remotes. When installing dual anchors, you can program a single Dash Switch and/or Key Fob remote to control both units as follows: Determine which HPU is paired with the controller by pressing the UP or DOWN button on the controller.
-
Page 10: Operation
Here you’ll find information on all of the functions, safe use, and proper maintenance of your shallow water anchor. If you have questions, contact our Technical Support Team at 1 + (813) 689-9932 option 2 or visit our website at www.power-pole.com. HPU (Hydraulic Pump Unit) Using Top Side Control Functions... - Page 11 FUNCTION 2: Key-Fob Speed Adjustment NOTE Default settings are set to 70% of the highest speed level. Tone increases with level (1-10). FIG. 1 1. Depress and hold the C-Monster PROGRAM button for 6 seconds until LED flashes and 2 chimes are heard followed by two beeps.
- Page 12 MULTIPLE ANCHORS With multiple Power-Pole anchors, the Dash Switch can be used to toggle between independent or simultaneous control of the anchors. Depressing and releasing the Directional Control button will toggle through the multiple anchors. The LED lights will flash corresponding to either left, right, or both to indicate the current control settings.
- Page 13 C-MONSTER Wireless Controller Battery Replacement Instructions IMPORTANT: Ensure the switch and the surrounding area is as dry as possible to avoid any moisture intrusion before changing battery in controller. Advanced Dash Switch Standard Key Fob Remote STEP 1 STEP 1 Remove the (2) #8 x 3/4”...
- Page 14 C-MONSTER Wireless Controller Battery Replacement Instructions continued Standard Foot Switch STEP 1 Remove the (3) screws with a #2 hillips head screwdriver. STEP 2 Separate the foot switch cover from its base using a small slotted flat head Figure 1 screwdriver.
-
Page 15: Maintenance And Storage
• Quick product registration. Now you can easily register your Power-Pole anchors and accessories directly through the app. • Theft recovery. Once you register your Power-Pole anchor with the C-Monster App, if it’s ever stolen we can help law enforcement track and recover it. - Page 16 • Do not use your Power-Pole shallow water anchor as a form of assistance for entering or exiting the vessel. • Never leave your boat unattended with the Power-Pole anchor as the primary anchorage.
-
Page 17: Frequently Asked Questions
Q: What maintenance is required with my Power-Pole shallow water anchor? A: The lower pivot bolts on your Power-Pole anchor need to be checked every 100 cycles and tightened as needed. Should you see any damaged bushings upon tightening, replace them immediately. - Page 18 A: This is caused by either an external or internal leak in the hydraulic system. First, check all hydraulic fittings and hose for leaks. If no external leaks are found, please contact our Technical Support Team. Q: What are JL Marine System’s hours of operation? A: Business hours, including Technical Support hours, are listed at www.power-pole.com.
-
Page 19: Warranty
2. Install Genuine Power-Pole Merchandise ONLY. This warranty is void if any non authorized parts are used or installed. 3. This warranty is void if the Power-Pole shallow water anchor is used commercially, structurally altered, or subject to stress beyond the physical limits of the manufactured material. - Page 20 CAUTION: Do not use the Power-Pole shallow water anchor as your primary anchorge. Never leave your boat unattended while anchored solely with the Power-Pole shallow water anchor. ©2017 all rights reserved. Power-Pole Shallow Water Anchor U.S. Patent No. 6,041,730...
Need help?
Do you have a question about the PRO II Series and is the answer not in the manual?
Questions and answers