Table of Contents
Advertisement
Quick Links
SPECIFICATIONS
NI sbRIO-9627
Single-Board RIO OEM Devices
This document lists the specifications for the NI sbRIO-9627. The following specifications are
typical for the -40 °C to +85 °C operating temperature range unless otherwise noted.
Caution
document. Product misuse can result in a hazard. You can compromise the safety
protection built into the product if the product is damaged in any way. If the product
is damaged, return it to NI for repair.
Processor
Type
Architecture
Speed
Cores
Operating system
Nonvolatile memory
Volatile memory (DRAM)
Real-time clock, accuracy
Flash reboot endurance
Note
For information about the life span of the nonvolatile memory and about best
practices for using nonvolatile memory, visit
.
SSDBP
1
Formatted nonvolatile memory may be slightly less than this value.
2
You can increase the flash reboot endurance value by performing field maintenance on the device.
If you expect that your application may exceed the maximum cycle count listed in this document,
contact NI support for information about how to increase the reboot endurance value.
Do not operate the sbRIO-9627 in a manner not specified in this
1
2
Xilinx Zynq-7000,
XC7Z020 All Programmable SoC
ARM Cortex-A9
667 MHz
2
NI Linux Real-Time (32 bit)
512 MB
512 MB
5 ppm
100,000 cycles
ni.com/info
and enter the Info Code
Advertisement
Table of Contents
Related Manuals for National Instruments NI sbRIO-9627
Summary of Contents for National Instruments NI sbRIO-9627
-
Page 1: Specifications
SPECIFICATIONS NI sbRIO-9627 Single-Board RIO OEM Devices This document lists the specifications for the NI sbRIO-9627. The following specifications are typical for the -40 °C to +85 °C operating temperature range unless otherwise noted. Caution Do not operate the sbRIO-9627 in a manner not specified in this document. -
Page 2: Operating System
C/C++ Development Tools for NI Linux Real-Time is an optional interface for C/C++ programming of the sbRIO-9627 processor. Visit ni.com/info and enter Info Code RIOCdev more information about the C/C++ Development Tools for NI Linux Real-Time. 2 | ni.com | NI sbRIO-9627 Specifications... -
Page 3: Rs-232 (Dte) Serial Port
Ethernet ports below -20 °C. If you expect ambient temperatures below -20 °C, NI recommends using a 10/100 network infrastructure or assigning 10/100Mbps communication speeds to the Ethernet Adapter in NI Measurement & Automation Explorer (MAX). NI sbRIO-9627 Specifications | © National Instruments | 3... -
Page 4: Embedded Can
RMC SD via FPGA 3.3 V DIO 1 (SDIO1) Supported Standards SD, SDHC Front Panel SD Throughput Read 12.0 MB/s maximum Write 9.0 MB/s maximum Both standard SD and microSD interfaces are supported. 4 | ni.com | NI sbRIO-9627 Specifications... - Page 5 Number of DIO channels Maximum tested current per channel ±3 mA Input logic levels Input low voltage, V -0.3 V minimum; 0.8 V maximum Input high voltage, V 2.0 V minimum; 5.25 V maximum NI sbRIO-9627 Specifications | © National Instruments | 5...
-
Page 6: Analog Input Characteristics
±25 V, for up to 2 AI pins Powered off ±15V AI accuracy Measurement Conditions Range Percent of Reading (Gain Percent of Range (Offset Error) Error) Typical (25 °C, ±5 °C) 0.042% 0.007% 0.007% 0.007% 10 V 0.008% 6 | ni.com | NI sbRIO-9627 Specifications... - Page 7 Crosstalk (10 kHz) -70 dB Typical performance Figure 1. Common Mode Rejection Ratio versus Frequency 1 V Range 2 V Range 5 V Range 10 V Range 1000 10000 Frequency (Hz) NI sbRIO-9627 Specifications | © National Instruments | 7...
-
Page 8: Analog Output Characteristics
–8 1000 10000 100000 1000000 Frequency (Hz) Figure 3. Settling Error versus Source Impedance 100000 10000 1000 1000 100000 10000 Source Impedance (Ω) Analog Output Characteristics Number of channels DAC resolution 16 bits 8 | ni.com | NI sbRIO-9627 Specifications... - Page 9 This is the maximum update rate when running one AO channel in a loop with the FPGA top-level clock set to 40 MHz. When the analog output initializes, a voltage glitch occurs for about 20 μs, peaking at 1.3 V, typical. Range is 5 V. NI sbRIO-9627 Specifications | © National Instruments | 9...
-
Page 10: Cmos Battery
The NI sbRIO device requires a power supply connected either to the power connector or through the VIN_filtered pins through the RMC. Refer to the Powering On the NI sbRIO Device section in the NI sbRIO-9627 Getting Started Guide on ni.com/manuals information about connecting the power supply. - Page 11 10/100Mbps communication speeds to the Ethernet Adapter in NI MAX. Refer to the Network/Ethernet Port section of this document for more information. Use digital approach to ensure the on-chip temperature reading is below 98°C. NI sbRIO-9627 Specifications | © National Instruments | 11...
- Page 12 Info Code . For device-specific guidelines about enabling sbriocooling proper thermal design, refer to the NI sbRIO-9627 User Manual on ni.com/manuals. Storage temperature -40 °C to 85 °C (IEC 60068-2-1, IEC 60068-2-2) Operating humidity (IEC 60068-2-78)
-
Page 13: Physical Characteristics
Battery Replacement and Disposal Battery Directive This device contains a long-life coin cell battery. If you need to replace it, use the Return Material Authorization (RMA) process or contact an Cd/Hg/Pb NI sbRIO-9627 Specifications | © National Instruments | 13... -
Page 14: Worldwide Support And Services
NI trademarks. Other product and company names mentioned herein are trademarks or trade names of their respective companies. For patents covering NI products/technology, refer to the appropriate location: Help»Patents in your software, the file on your media, or the National Instruments Patent Notice at . You can find patents.txt ni.com/patents...
Need help?
Do you have a question about the NI sbRIO-9627 and is the answer not in the manual?
Questions and answers