Inficon D-TEK Select Operating Manual
  1. Manuals
  2. Brands
  3. Inficon Manuals
  4. Security Sensors
  5. D-TEK Select
  6. Operating manual

Inficon D-TEK Select Operating Manual

Refrigerant leak detector
Hide thumbs

Advertisement

Table of Contents

O P E R A T I N G
M A N U A L
D-TEK™ Select
Refrigerant Leak Detector
EN

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the D-TEK Select and is the answer not in the manual?

Questions and answers

Related Manuals for Inficon D-TEK Select

Summary of Contents for Inficon D-TEK Select

  • Page 1 O P E R A T I N G M A N U A L D-TEK™ Select Refrigerant Leak Detector...

  • Page 2: Declaration Of Conformity

    Equipment Description ....D-TEK Select Refrigerant Leak Detector Applicable Directives .
  • Page 3 Thank you for buying the INFICON D-TEK Select Refrigerant Leak Detector! With normal use, your D-TEK Select from INFICON will give you years of trouble-free service. To get the best performance from your D-TEK Select, please read this manual carefully before you start using the instrument. If you have any questions or need additional assistance, please call 800-344-3304.

  • Page 4: Getting Started

    Getting Started The D-TEK Select is shipped with the infrared cell and power stick installed. The nickel/metal hydride batteries in the power stick are not yet charged. To charge them, connect the cord of the AC power adapter to the power jack at the rear of the instrument, and plug the adapter into the appropriate mains outlet.

  • Page 5: Finding Leaks

    3. When the instrument detects a leak source, its yellow LEDs will illuminate and it will beep rapdily. 4. When the D-TEK Select signals a leak, pull the probe away from the leak for a moment, then bring it back to pinpoint the location.

  • Page 6: Using The Manual Zero Mode

    Increases in concentrations of refrigerants will be displayed by the illumination of the yellow LEDS. For best test results, allow the D-TEK Select to warm up for 5 - 10 minutes before engaging manual zero mode.

  • Page 7: Recharging The Power Stick

    LED and the amber battery charging LED will flash. Recharge the D-TEK Select by connecting the supplied AC power adapter, or using the cigarette lighter adapter. NOTE: The D-TEK Select does not need to be fully charged to operate nor fully discharged before recharging. W A R N I N G Do not attach any other power cords to the D-TEK select’s power...

  • Page 8: Changing The Filter Cartridge

    NOTE: It is very important that you operate the D-TEK Select with a filter cartridge installed at all times. Failure to do so could damage the leak...

  • Page 9: Changing The Infrared Cell

    This specialized IR cell will operate for about 1000 hours. The D-TEK Select will flash all the yellow leak LEDs when the IR cell has reached the end of its useful life. To replace the IR cell: 1.

  • Page 10: Removing/Replacing The Power Stick

    Disengage the connector and slide the power stick out of the D-TEK Select. Slide the new stick into the D-TEK Select and push the miniature connector on the power stick into the mating half on the PCB board. Do not bend the PCB board’s connector away from the board.

  • Page 11: Replacement Parts And Accessories

    Replacement Parts and Accessories Replacement parts and accessories for your D-TEK Select are available through the same dealer from whom you bought the instrument. Molded plastic storage case....... . . 712-702-G1 Headphones .

  • Page 12: Troubleshooting Guide

    90 seconds to ready to use. see if the unit starts to beep and the lights stop scrolling. If not, contact INFICON. 2d) Battery may be 2d) See #3 below. dead. 2c) Filter cartridge 2c) Replace used filter may be clogged, cartridge with a new one.

  • Page 13: Warranty And Liability-Limitation

    MERCHANTABILITY or of FITNESS FOR A PARTICULAR PURPOSE or otherwise. All such other warranties are expressly disclaimed. INFICON shall have no liability in excess of the price paid to INFICON for the instrument plus return transportation charges prepaid. INFICON shall have no liability for any...

  • Page 14: Return Materials Authorization Procedure

    Return Materials Authorization Procedure All instruments and parts returned to INFICON for repair or credit must be properly packaged, insured, shipped transportation charges prepaid, and must have a Return Material Authorization (RMA) number issued before the material is returned. The RMA number is to be marked on all shipping labels and packing slips.
  • Page 16 TWO TECHNOLOGY PLACE EAST SYRACUSE, NY 13057-9714 USA Phone: +1.800.344.3304 Fax: +315.437.3803 E-Mail: service.tools@inficon.com www.inficonservicetools.com 074-392-P1L...

Table of Contents

Save PDF