Anviz VF30 User Manual

Reader Appearance
40mm
80mm
IN IN
14:03 14:03
09
09
10-29-09
10-29-09 THU THU
180mm
F i n g e r p r i n t A c c e s s c o n t r o l C a r d A c c e s s c o n t r o l S i d e V i e w
F r o n t V i e w F r o n t V i e w
Cancel/Power Key
Menu Key
Exit/Cancel the Present Operation
Enter System Management Menu
Power on/Power off
Workcode Setup Key
State Key(Clock In)/Up
Door Bell Key
State Key(Clock Out)/Down
Num. Keys
0-9
Confirm Key
Enter Employee ID or Password
Confirm Present Operation
Operation Guide
Enroll User:
1 Each user can register two fingerprints, one password and one RFID card.
IN MENU User
09 : 00 User Enroll
[M] [OK]
26
Setup Delete
10-11-17 WED USB Flash Verify Mode
Select [User] Select [Enroll]
Enroll Fingerprint:
Place the same finger on the sensor twice in a row to enroll fingerprints.
Enroll FP
Enroll Enroll FP
FP 1/2
press [OK]
[OK]
Password/Card Place Finger #1
Esc-C Set-OK
Select [FP] Enroll fingerprint
Enroll Password:
Password length: 000000-999999.
Enroll Enroll PWD
FP 1/2
press [OK]
[OK] [OK]
Password /Card PWDID
******
Esc-C Set-OK
Esc-C Set-OK
Select [Password] Input password
Enroll Card ：
Enroll Enroll Card
FP 1/2
press [OK]
[OK]
Password/ Card Swipe card!
Esc-C Set-OK
Select [Card] Swipe the card
Admin Setup:
2 Admin(Administrator) has full access permissions to the device. It is recommended to assign a minimum of
two administrators to each unit.
MENU User Admin Setup
▼
Group Setup
User
[OK] [OK]
Admin Setup
Setup
USB Flash Admin Clear Esc-C
Select [User] Selelct [Admin Setup]
Menu List
Press [M] key to enter system management menu.
(This requires the administrator authorization if there is admin
registered in the system.) Menu List:
Enroll Dev ID
Time
Delete
Verify Mode Language
User
Group Setup
Workcode Scope
Admin Setup Net
Admin Clear Precision
Unlock
System Door Alert
Auto Off
Auto Update
Setup
Image Disp.
Log Alert
Log Setup
Re-Verify
Keypad, LCD, Sensor, Flash
Hardware Test
System Info User, FP, Log, Serial,FirmVer
Enroll
▼
[OK]
ID 008101
Esc-C Set-OK (ID：000001-999999）
Input user ID
Enroll FP Enroll FP Enroll FP
Take Off! Place Finger #2 Take Off!
Enroll PWD
Enroll PWD
PWDID [OK]
******
008101-P
Confm
Cancel-C Sav-OK
******
Input password again
Press [OK] to save
Enroll Card Enroll Card
008101-C
Cancel-C Sav-OK
Press [OK] to save
Admin Setup
Admin Setup Admin Setup
ID
[OK] [OK] [OK]
ID 000000 008101
Add-OK No-C Yes-OK Esc-C
Input Admin ID Setup successful
Other Setup
Verify Mode:
M→[User]→[OK]→[Verify Mode]→[OK]→[OK]→Input employee ID→[OK]→
Use [ /IN]/[OUT/ ] to select 'ANY/RF+FP/PW+FP/RF+PW/ID+FP'→[OK]→[OK].
Item
Any Fingerprint only, Card only or ID+Password only
It requires both Card and Fingerprint
RF+FP
Mode
verification together
It requires both Password and Fingerprint verification
IP Address
PW+FP
together
Subnet Mask
It requires both Card and Password verification
RF+PW
MAC Address together
Gateway IP
ID+FP Enter the user ID first then verify the fingerprint
Server IP
Factory default
setting
Server Port
Group Setup:
M→[User]→[OK]→[Group Setup]→[OK]→[OK]→
Input employee ID→[OK]→Input the group ID→[OK]→[OK].
Item
G00 The user in Group00 can not open the door
G01 The user in Group01 can open the door anytime
It is according to the Group & Time zone setting which
G02-16
can be set through the software
Factory default
setting
Tips: Group setup is used for managing the access control privileges. Each group can
contain 4 time zones.
Dev ID:
M→[Setup]→[OK]→[System]→[OK]→[Dev ID]→[OK]→
Input the device's ID→[OK]→[C]→[OK].
Item
Device ID of the unit which is required in software
1-99999999
communication
Factory default
setting
Tips: It doesn't allow duplicate Device ID in one LAN. Otherwise, it will cause software
communication error.
Language:
M→[Setup]→[OK]→[System]→[OK]→[Language]→[OK]→
Use [ /IN]/[OUT/ ] to select ENG/FRCH/GERM/...→[OK]→[C]→[OK].
Item
Enroll FP
Languages
Optional 4 languages.
008101-1
Cancel-C Sav-OK
Factory default
Press [OK] to save
Related Language
setting
Place finger straight and
flat on the sensor. Insure
maximum sensor coverage.
008101
Add-OK
WorkCode:
M→ [Setup]→[OK]→[System]→[OK]→[WorkCode Scope]→[OK]
→Input Max→[OK]→Input Min→[OK] →[C]→[OK].
Explanation
Item
0-999999
Factory default
setting
Tips: WorkCode indicates the work type，easily distinguishes which attendance record
is related to which work type.
Net:
M→ [Setup]→[OK]→[System]→[OK]→[Net]→[OK]→to select [Mode/IP Address/Subnet Mask
/MAC Address/Gateway IP/Server IP/Server Port]→[OK]→Modify parameters→[C]→[OK].
Item
Any
TCP/IP Server mode: Common network mode
Mode
TCP/IP Client mode: Only communicate
with the PC which has static IP
Set terminal IP address when communication
of TCP/IP, IP address must be a static
IP Address
IP address
Explanation
Subnet Mask Subnet Mask of the LAN
Unique Physical address of the network moudle. This
MAC Address
setting can not be modified.
Gateway IP Default Gateway of the LAN
The IP address of the Sever Machine
when using Client Mode TCP/IP
Server IP
communication.
G01
It's the Software Port number used when the
Server Port
read is configured for TCP/IP communication
Unlock:
M→ [Setup]→[OK]→[System]→[OK]→[Unlock]→[OK]→No/1~15→[OK]→
[C]→[OK]. 'No'-no delay time; The maximum delay time is 15 seconds.
Item
Explanation
The duration of the audible alarm to notify employees
1-15
of events. (Lunch, break, Off Duty)
It generates a door close signal immediately after
1 No
it generates the door open signal
Factory default
setting
Door Alert:
M→ [Setup]→[OK]→[System]→[OK]→[Door Alert]→[OK]→
to select No/1~99→[OK]→[C]→[OK]. 'No'-no alert signal.
Item
Explanation
It generates the door open alarm signal if the door open
1-99
time is longer than the preset value
No Disable the door open alarm
Factory default
setting
Illustration for placing fingerprint
Place finger in the center of the sensor.
Explanation
Valid scope for the Workcode
Max 999999
Min 0
Factory default
Explanation
setting
Server Mode
192.168.0.218
255.255.255.0
192.168.0.1
192.168.0.7
5010
Explanation
5
Explanation
15
Place finger on the sensor surface