Anviz TC550 Operation Manual

TC550/OC500
Product Appearance
1 1
TC550 OC500
2 2
8
9
3 5 6 7 3 5 6 7
10
4 4
11
12
1.LCD
2.Loudspeaker
3.FN key
4.0-9 Num. Key
5.State Key(Clock In)/Page Up
6.State Key(Clock Out)/Page Down
Illustration for placing finger
Correct method :
Place finger in the center of the sensor. Place finger flat on the sensor surface.
Operation Guide
Enroll User:
Each user can register two fingerprints, one password and one card.
IN MENU ▼ User ▼
09 : 00 User Enroll
[M] [OK]
26
Setup Delete
10-11-17 WED USB Flash Verify Mode
Select [User] Select [Enroll]
Enroll Fingerprint :
Place finger on the sensor twice to enroll fingerprints.
Enroll Enroll FP Enroll FP
FP 1/2
[OK] [OK]
Password/Card Place Finger #1 Place Finger #2
Esc-C Set-OK
Select [FP] Enroll fingerprint
Enroll Password:
Password length: 0-999999.
Enroll Enroll PWD Enroll PWD
FP 1/2
[OK] [OK] [OK] PWD ID
Password /Card PWD ID
******
Esc-C Set-OK Confm
Esc-C Set-OK
Select [Password] Input password Input password again
Enroll Card:
Enroll Enroll Card Enroll Card
FP 1/2
[OK] [OK]
Password/ Card Swipe card! 008101-C
Esc-C Set-OK Cancel-C
Select [Card] Swipe the card Press [OK] to save
Admin Setup:
Admin(Administrator) has all the privileges of the machine. Please pay attention to the admin setup.
IN MENU ▼ User ▼
09 : 00 Admin Setup
User
[M] [OK]
26
Setup Admin Clear
10-11-17 WED USB Flash
Select [User] Selelct [Admin Setup]
Fingerprint & Card Time Attendance and Access Control Operation Guide
Menu List
Press [OK] about 3 seconds to turn on the device, press [M] key to enter the
system menu. Menu list:
Dev ID
Enroll
Time
Delete
Language
User
Verify Mode
8
Workcode Scope
Group setup
9
Net
Admin Setup
Precision
Admin Clear
Volume
System
11
Unlock/Ring
Auto Off
Auto Update
Setup
12
Image Disp.
Log Alert
Log Setup
Re-Verify
Hardware Test Keypad, LCD, Voice, Sensor, Flash
New Log Backup
All Logs Backup
A Standard USB flash drive with a
USB Flash
maximum capacity to 2GB of RAM
User Backup
is required.
User Reco!
System Info User, FP, Log, Serial,FirmVer
Incorrect method :
Do not remove finger during Using the tip of your finger.
the enrollment process.
(The function with mark in the menu is for the specific
model unit. Please follow as actual product's menu. )
Enroll
[OK]
ID 008101
Esc-C Set-OK
(ID number range:0-999999)
Input user ID
Enroll FP
008101-1
Sav-OK
Press [OK] to save
Enroll PWD
[OK]
******
008101-P
Cancel-C Sav-OK
******
Press [OK] to save
Sav-OK
Admin Setup Admin Setup Admin Setup
[OK] [OK] [OK]
ID 000000 008101
Esc-C Add-OK No-C Yes-OK
Input Admin ID
Other Setup
Verify Mode: M→[User]→[OK]→[Verify Mode]→[OK]→[OK]→Input employee ID→[OK]→
Use [IN／ ]/[OUT/ ] to select 'ANY/RF+FP/PW+FP/RF+PW/ID+FP'→[OK]→[OK].
Item
Mode
Any Fingerprint only, Card only or ID+Password only
IP Address
It requires both Card and Fingerprint
Subnet Mask RF+FP
verification together
MAC Address
It requires both Password and Fingerprint verification
PW+FP
Gateway IP
together
Server IP
It requires both Card and Password verification
RF+PW
together
Server Port
ID+FP Enter the user ID first, then verify the fingerprint
Factory default
setting
M→[User]→[OK]→[Group Setup]→[OK]→[OK]→
Group Setup:
Input employee ID→[OK]→Input the group ID→[OK]→[OK].
Item
G00 The user in Group00 can not open the door
G01 The user in Group01 can open the door anytime
It is according to the Group & Time zone setting which
G02-16
can be set through the software
Factory default
setting
Tips: Group setup is used for managing the access control privileges. Each group can
contain 4 time zones.The default setting: G01．
M→[Setup]→[OK]→[System]→[OK]→[Dev ID]→[OK]→Input the device's ID
Dev ID:
→[OK]→[C]→[OK].
Item
Device ID of the unit which is required in software
Sliding, Rolling or Moving finger 1-99999999
communication
during the enrollment process.
Factory default
setting
WorkCode: M→ [Setup]→[OK]→[System]→[OK]→[WorkCode Scope]→[OK]
→Input Max→[OK]→Input Min→[OK] →[C]→[OK].
Item
0-999999
Factory default
setting
Tips: WorkCode indicates the work type，easily distinguishes which attendance record
is related to which work type.
Wiring Diagram
Admin Setup U Disk
008101
ID
[OK]
Esc-C Add-OK
Setup successful
Net: M→ [Setup]→[OK]→[System]→[OK]→[Net]→[OK]→to select [Mode/IP Address/Subnet Mask
/MAC Address/Gateway IP/Server IP/Server Port]→[OK]→Modify parameters→[C]→[OK].
Item
Explanation
Mode
IP Address
Subnet Mask
MAC Address
Gateway IP
Any
Server IP
Server Port
Explanation
Precision, Volume, Auto off, Auto Update, Image Disp., Log Alert, Re-Verify
Item
Precision
Volume
G01
Auto off
Auto Update
Image Disp.
Explanation
Log Alert
1
Re-Verify
Language: M→[Setup]→[OK]→[System]→[OK]→[Language]→[OK]→
Explanation Use [IN/
Item
Valid scope for the Workcode
Max 999999 Language
Min 0
Factory default
setting
Wiegand Output
Wiegand Input
Mini USB
USB
TCP/IP
Power
TCP/IP
V1.2
Factory default
Explanation
setting
TCP/IP Server mode: Common network mode
TCP/IP Client mode: Only communicate Server Mode
with the PC which has static IP
Set terminal IP address when communication
of TCP/IP, IP address must be a static 192.168.0.218
IP address
Subnet Mask of the LAN
255.255.255.0
Unique Physical address of the network moudle. This
setting can not be modified.
Default Gateway of the LAN 192.168.0.1
The IP address of the Sever Machine
when using Client Mode TCP/IP 192.168.0.7
communication.
It's the Software Port number used when the
5010
read is configured for TCP/IP communication
Explanation
Set terminal fingerprint matching precision.
0-[Normal],1-[Good], 2-[Exact].
Set the terminal voice volume.
0-[mute], 5-[Max].
Set the time duration for an idle clock to go into sleep
mode. No-[Not Off], 250min-[Max Time].
Auto update means the previous lower quality fingerprint
template will be automatically replaced by the new higher
quality one during fingerprint verification.
Choose to display the fingerprint image on the screen during
the verification process. [Yes] - show fingerprint image,
[No] - not show fingerprint image
The terminal will alarm when the memory capacity
is less than the [Log Alert] value.[No]-Not alarm,
Max. value 5,000.
The duration of time in which the terminal will ignore
repeated attempts for authentication.
[No]: Disable the function; Max. value is 250 min.
]/[OUT/ ] to select ENG/FRCH/GERM/...→[OK]→[C]→[OK].
Explanation
Contains 11 languages:
ENG(English), FRCH(French), GERM(German), SPAN(Spanish),
PTG(Portuguese), ITA(Italian), BULG(Bulgarian), SLVK(Slovak),
HUNG(Hungarian), SLVN(Slovenian), TURK(Turkish)
Related Language