Table of Contents
Advertisement
Manual programming is disabled after your lock is programmed using the mobile app. If you
manually program your lock and choose to later link your lock to the app, all manually programmed
Add or Delete User Codes
1
Enter 6 digit
Enter
Programming
user code
Code
add or delete
light on
Change Programming Code
1
Enter current
Enter 6 digit
Programming
Programming
Code
Code
again
light on
Change User Code Length
CAUTION
Changing the user
code length will
delete all codes
currently in the
lock.
Delete All Codes
CAUTION
You cannot
recover deleted
user codes! Make
sure you have
your default
codes available!
Manual Programming Guide
user codes and the programming code are deleted.
2
3
Choose and
press:
to
add
or
delete
add/delete another
user code
2
3
Enter
new
Programming
Code
1
2
Enter 6 digit
Choose the
Programming
code length
Code
(from 4 - 8 digits)
and press
and hold that
light on
number.
1
2
Enter 6 digit
Press and hold:
Programming
Code
light on
CAUTION
4
5
Re-enter
Press to exit
user code to
confirm
indicates
success
4
5
Re-enter new
Press to exit
Programming
Code
to confirm
indicates
success
3
While you're
Release then
holding the
number
Press
3
While you're
Release then
holding
Press
4
5
Success!
User code
choose:
length has
been changed!
confirm
indicates
success
or
cancel
4
5
Success! All codes
are deleted. See
choose:
the sticker on the
back of the Quick
Start Guide or the
confirm
back of the inside
or
escutcheon for
your default codes.
cancel
indicates
success
Hide quick links:
Advertisement
Table of Contents
Need help?
Do you have a question about the BE489WB and is the answer not in the manual?
Questions and answers
My lock is not working; the x is blinking red. I think I held the back button too long when I was trying to pair my phone with the lock because it said it couldn’t find device. Now, I can’t use code on lock or move lock with phone. Please tell me what I can do to get it working again.
A blinking red light on the Schlage BE489WB lock may indicate a failed Factory Default Reset (FDR). To fix this, perform an FDR by following these steps:
1. Remove the battery cover.
2. Press and hold the black circle reset button to the right of the thumbturn on the inside of the lock for 7 seconds, then release.
3. If successful, all keypad lights will illuminate for 3 seconds.
4. The blue checkmark will stay on for an additional 2 seconds and the lock will beep.
If the red "X" remains lit and the lock beeps, the reset has failed. Try the process again. If the issue persists, consider replacing the batteries with new alkaline AA batteries or contacting Schlage customer support.
This answer is automatically generated
At the conclusion of the lock/unlock cycle, the ‘unlock button’ flashes and timed with noise. What is this telling me?
Can I get parts for this system?
Multiple factory resets have failed. What do I do now.
can this lock be set to auto lock without the app
Yes, the Schlage BE489WB lock can be set to auto lock without using the app. The auto lock delay can be adjusted directly on the lock.
This answer is automatically generated
@Mr. Anderson
if the BE489WB can be programed to auto lock without app please reply with directions
No, once the Schlage BE489WB lock is connected to the app, manual programming functions are disabled. Therefore, auto-lock settings would need to be configured through the app.
This answer is automatically generated
why doesn't it connect after changing the batteries
The Schlage BE489WB may not connect after changing the batteries if the batteries were not installed correctly, such as not facing the door, or if the battery holder and cover were not reinstalled properly. Additionally, once the lock is connected to the app, manual programming is disabled and access codes are deleted, so reconnection may require using the app.
This answer is automatically generated
How do I change Wi-Fi routers
There is a white light flashing on the lock and I have replaced the batteries
Lock will not connect to the wifi