Évacuation À L'extérieur Par L'arrière (Conduit Horizontal De Type B) - Blomberg BOTR30200CSS Installation Manual

Installation
5
5.2.2 Évacuation à l'extérieur par
l'arrière (conduit horizontal de
type B)
3/8" TO EDGE
12"
TO
NOTE: IT IS VERY IMPORTANT
THE DIRECTIONS
READ AND FOLLOW INSTRUCTION S
IN THE INSTALLATION
WITH THIS
BEFORE PROCEEDING
REAR WALL TEMPLATE.
4"
serves to position the bottom
This Rear Wall Template the horizontal exhaust
mounting plate and to locate
outlet.
1. Use a level to check that the template is positioned
accurately. one stud on the left or
2. Locate and mark at least
right side of the centerline.
It is important to use at least one wood
a stud to support the weight
screw mounted firmly in two additional, evenly spaced
of the microwave. Mark
locations for the supplied toggle bolts.
locations. Where there is
3. Drill holes in the marked for wood screws. For holes
a stud, drill a 3/16" hole stud, drill 5/8" holes for
that do not line up with a
toggle bolts. MOUNTING PLATE
DO NOT INSTALL THE
AT THIS TIME.
from the rear wall.
4. Remove the template book for your
5. Revie w h t e Installation Instruction
installation situation.
Darle vuelta a la hoja para consultar la
versión en Español.
to align with holes in the
Locate and mark holes
mounting plate.
IMPORTANT: STUD ON EITHER SIDE OF
LOCATE AT LEAST ONE
THE CENTERLINE. EVENLY
MARK THE LOCATION FOR 2 ADDITIONAL,
IN THE MOUNTING PLATE
SPACED TOGGLE BOLTS
AREA.
along the dotted line.
Trim the rear wall template
Vue d'ensemble de l'installation
B1. Préparation du mur arrière
B2. Retrait de la plaque du ventilateur
B3. Fixation de la plaque de montage au mur
B4. Préparation de l' a rmoire supérieure
B5. Ajustement du ventilateur
B6. Installation du four à micro-ondes
Assurez-vous que les vis du moteur
du ventilateur et de la plaque du
A
ventilateur sont correctement ser-
rées lorsque vous les remettez en
place. Cela permet d' é viter des vibra-
tions excessives.
Assurez-vous que le câblage du mo-
A
teur a été effectué et correctement
fixé, et que les câbles ne sont pas
coincés.
54 / 63 FR
Four à micro-ondes à convection à hotte intégrée / Manuel d'installation
Trim the rear wall template along the dotted line.
Locate and mark holes to align with holes in the
t a . e
m o u t n n i g l p
IMPORTANT: STUD ON EITHER SIDE OF
LOCATE AT LEAST ONE
THE CENTERLINE.
FOR 2 ADDITIONAL, EVENLY
MARK THE LOCATION
IN THE MOUNTING PLATE
SPACED TOGGLE BOLTS
AREA.
B1. Préparation du mur arrière pour
l'évacuation à l'extérieur par l'arrière
Vous devez percer une ouverture dans le mur ar-
rière pour l' é vacuation à l' e xtérieur.
NOT E: IT IS VER
REA D
AND FOLL Y IMPO RTAN
IN THE OW THE T TO
BEFO INST AL L DIRE CTIO
RE PRO A T I O N I N NS
REA R WAL L CEE DING S TRUC TION S
TEM PLAT WITH
This Rear Wall Templa E. THIS 3/8" TO EDGE
mounti ng plate te serves
outlet. and to to positio 12"
1. Use locate the horizon n the bottom
a level to check tal exhaus
accura tely. that the t
2. Locate and mark templa te is positio
right side at least ned
of the centerl one stud on the 4"
screw mounte It is importa ine. left or
d firmly nt to use at least
of the microw in a stud one wood
locatio ns ave. Mark two additio to suppor
3. Drill holes in for the supplie nal, evenly t the weight
a stud, the marked d toggle bolts. spaced
drill a 3/16" locatio ns.
that do not line hole for wood screws Where there is
toggle bolts. up with a stud,
drill 5/8" . For holes
AT THIS DO NOT INSTA LL holes for
4. Remov TIME. THE MOUN
e the templa TING PLATE
5. Review the Installa te from
installa tion situatio tion Instruc the rear wall.
n. tion book
for your
Darle vuelta
versió n a la hoja
en Españ para consu
ol. ltar la
Loca te and mark
moun ting holes to
plate . align with
IMPO RTAN holes in
T: the
LOC ATE
AT LEAS
THE CEN T ONE
TERL INE. STUD
MAR K THE LOC ON EITH
SPAC ATIO N ER SIDE
ED TOG FOR 2 OF
ARE A. GLE BOLT ADD ITION
S IN THE AL, EVEN
MOU NTIN LY
G PLAT
E
Trim the
rear wall
temp late
alon g
the dotte
d line.
Loca te
and mark
moun ting
plate .
IMPO RTAN
T:
LOC ATE
AT LEAS
THE CEN
MAR K TERL INE.
THE LOC
SPAC
ED TOG
ARE A.
• Lisez les instructions relatives au GABARIT
POUR MUR ARRIÈRE.
• Collez-le au mur arrière avec du ruban adhésif,
en l' a lignant sur les trous préalablement percés
pour les trous A et B de la plaque de montage.
• Percez l'ouverture conformément aux
instructions sur le GABARIT POUR MUR ARRIÈRE.
Trim the
rear wall
temp late
alon g the dotte
d line.
holes to
align with
holes in
the
T ONE
STUD ON EITH
ER SIDE
ATIO N OF
FOR 2
GLE BOLT ADD ITION
S IN THE AL, EVEN
MOU NTIN LY
G PLAT
E