Mitsubishi Electric MELSEC iQ-F FX5 Hardware Manual

Side
JAPANESE
A
Side
ENGLISH
B
MELSEC iQ-F FX5
Simple Motion Module
Hardware Manual
B C N -B 6 20 08-
Manual Number
337
Revision E
December
Date
2017
This manual describes the part names, dimensions, installation, and
specifications of the product. Before use, read this manual and manuals of
relevant products fully to acquire proficiency in handling and operating the
product. Make sure to learn all the product information, safety information, and
precautions.
And, store this manual in a safe place so that you can take it out and read it
whenever necessary. Always forward it to the end user.

Registration: Ethernet is a trademark of Xerox Corporation. MODBUS is a registered
trademark of Schneider Electric SA. Phillips is a registered trademark of Phillips Screw
Company.
The company name and the product name to be described in this manual are the
registered trademarks or trademarks of each company.
Effective December 2017
Specifications are subject to change without notice.

2014 Mitsubishi Electric Corporation
Safety Precaution
(Read these precautions before use.)
This manual classifies the safety precautions into two categories:
and .
Indicates that incorrect handling may cause hazardous
conditions, resulting in death or severe injury.
Indicates that incorrect handling may cause hazardous
conditions, resulting in minor or moderate injury or
property damage.
Depending on the circumstances, procedures indicated by
cause severe injury.
It is important to follow all precautions for personal safety.
Side
B
STARTUP AND
MAINTENANCE
PRECAUTIONS
 Do not touch any terminal while the PLC's power is on.
Doing so may cause electric shock or malfunctions.
 Before cleaning or retightening terminals, cut off all phases of the power
supply externally. Failure to do so in the power ON status may cause electric
shock.
 Before modifying the program in mid-operation, forcing output, running or
stopping the PLC, read through this manual carefully, and ensure complete
safety.
An operation error may damage the machinery or cause accidents.
 Do not change the program in the PLC from two or more peripheral equipment
devices at the same time. (i.e. from an engineering tool and a GOT)
Doing so may cause destruction or malfunction of the PLC program.
 Use the battery for memory backup in conformance with the MELSEC iQ-F
FX5 User's Manual (Hardware).
- Use the battery for the specified purpose only.
- Connect the battery correctly.
- Do not charge, disassemble, heat, put in fire, short-circuit, connect
reversely, weld, swallow or burn the battery, or apply excessive force
(vibration, impact, drop, etc.) to the battery.
- Do not store or use the battery at high temperatures or expose to direct
sunlight.
- Do not expose to water, bring near fire or touch liquid leakage or other
contents directly.
Incorrect handling of the battery may cause excessive heat, bursting, ignition,
liquid leakage or deformation, and lead to injury, fire or failures and malfunction
of facilities and other equipment.
Associated Manuals
Manual name Manual No.
MELSEC iQ-F FX5
Explains Simple Motion module
Simple Motion Module User's
IB-0300251 specifications, functions list and
Manual
wiring.
(Startup)
MELSEC iQ-F FX5
Explains Simple Motion module
Simple Motion Module User's
IB-0300253 f u n c t i o ns , p r o g r a m m i n g a n d
Manual
troubleshooting.
(Application)
MELSEC iQ-F FX5
F unc t i ons , pr og ra mmi n g a nd
Simple Motion Module User's
buffer memory for the
Manual IB-0300255
synchronous control of the Simple
( A d v a nc ed S y n c h r on o us
Motion module.
Control)
MELSEC iQ-F Explains FX5U CPU module
FX5U User's Manual JY997D55301 specification details for I/O, wiring,
(Hardware) installation, and maintenance.
MELSEC iQ-F Explains FX5UC CPU module
may also
FX5UC User's Manual JY997D61301 specification details for I/O, wiring,
(Hardware) installation, and maintenance.
System configuration, parameter
GX Works3 Operating settings, and online operations
SH-081215ENG
Manual (common to simple project and
structured project) of GX Works3.
How to obtain manuals
For the necessary product manuals or documents, consult with your local Mitsubishi
Electric representative.
Certification of UL, cUL standards
FX5-40SSC-S or FX5-80SSC-S comply with the UL standards (UL, cUL).
Further information can be found in the following manual.
MELSEC iQ-F FX5U User's Manual (Hardware)
MELSEC iQ-F FX5UC User's Manual (Hardware)
Regarding the standards that relate to the CPU module, please refer to either the
product catalog or consult with your nearest Mitsubishi product provider.
Attention
This product is designed for use in industrial applications.
Compliance with EC directive (CE Marking)
This note does not guarantee that an entire mechanical module produced in
accordance with the contents of this note will comply with the following standards.
Compliance to EMC directive and LVD directive for the entire mechanical module
should be checked by the user / manufacturer. For more information please consult
with your nearest Mitsubishi product provider.
Attention
 This product is designed for use in industrial applications.
Note
 Manufactured by:Mitsubishi Electric Corporation
2-7-3 Marunouchi, Chiyoda-ku, Tokyo, 100-8310 Japan
 Manufactured at:Mitsubishi Electric Corporation Nagoya Works
1-14, Yada-minami 5-chome, Higashi-ku, Nagoya, Japan
 Authorized Representative in the European Community:
Mitsubishi Electric Europe B.V.
Gothaer Str. 8, 40880 Ratingen, Germany
Requirement for Compliance with EMC directive
The following products have shown compliance through direct testing (of the identified
standards below) and design analysis (through the creation of a technical construction
file) to the European Directive for Electromagnetic Compatibility (2004/108/EC) when
used as directed by the appropriate documentation.
Type: Programmable Controller (Open Type Equipment)
Models: MELSEC iQ-F series manufactured
from October 1st, 2014 FX5-40SSC-S
from October 1st, 2016 FX5-80SSC-S
Standard
EN61131-2: 2007
Programmable controllers
- Equipment requirements and tests
Description
Caution for EC Directive
Attach the ferrite core to the power supply cable (Simple Motion module side).
Attach the ferrite core in 200 mm (7.87") or less from connector on the
Simple Motion module side.
The ferrite core should use the following
Simple
equivalent product. (2 turns necessary)
Motion
module
Model name: ZCAT3035-1330
Ferrite core
Power supply cable
1. Outline
FX5-40SSC-S or FX5-80SSC-S type Simple Motion module (hereinafter referred to as
FX5SSC) is a intelligent function module applicable to SSCNETIII(/H).
FX5SSC can perform positioning control by servo motor via SSCNETIII(/H) applied
servo amplifier.
For positioning control, refer to the following manual.
MELSEC iQ-F FX5 Simple Motion Module User's Manual (Startup)
MELSEC iQ-F FX5 Simple Motion Module User's Manual (Application)
For synchronous control, refer to the following manual.
MELSEC iQ-F FX5 Simple Motion Module User's Manual
1.1 Incorporated Items
Verify that the following product and items are included in the package:
Product Module
Included Items
1.2 External Dimensions and Part Names
2-φ4.5 Mounting hole
[3]
[2]
[1]
16 (0.63")
50 (1.97")
[12]
[13]
Remark
Compliance with all relevant aspects of
the standard.
EMI
 Radiated Emission
 Conducted Emission
EMS
 Radiated electromagnetic field
 Fast transient burst
 Electrostatic discharge
 High-energy surge
 Voltage drops and interruptions
[1] External input connection connector
 Conducted RF
[2] Extension cable
 Power frequency magnetic field
[3] Direct mounting hole: 2 holes of 4.5
(0.18") (mounting screw: M4 screw)
[4] Axis display LED
[5] POWER LED
[6] RUN LED
[7] ERROR LED
[8] Extension connector
(Manufactured by TDK co., Ltd.)
(Advanced Synchronous Control)
 FX2NC-100MPCB Power supply cable (1 m)  1 cable
 Dust proof protection sheet  1 sheet
 Hardware manual (This manual)
Unit: mm (inches)
[4]
[5]
[6]
[7]
[9]
[8]
[10]
[11]
8 (0.32")
83 (3.27")
Axis display LED for FX5-40SSC-S
[4]
[14]
Axis display LED for FX5-80SSC-S
[4]
MASS (Weight): Approx. 0.3 kg (0.66 lbs)
Outer painting color: Munsell 0.6B7.6/0.2
[9] DIN rail mounting groove
(DIN rail: DIN46277, 35 mm (1.38")
wide)
[10] Name plate
[11] DIN rail mounting hook
[12] Pullout tab
[13] Power supply connector
[14] SSCNETIII cable connector