Step Ten: Testing The Assembly; Post Assembly Adjustments; Maintenance; Storage - Teeter Hang Ups F5000 Assembly Instructions

STEP TEN
Testing the Assembly
PRIOR TO USE:
• Test the table by hand for smooth and steady rotation.
• Ensure all fasteners are secure.
You have completed the assembly of your Teeter Hang Ups
• Read your Owner's Manual thoroughly before using the inversion table. Improper
settings could result in serious injury or death.
• For your reference, the table's serial number can be found at the base of the table
frame on the back.
• Please complete and mail your warranty card, or submit it on-line at www.teeterhangups.com.

POST ASSEMBLY ADJUSTMENTS

CHANGING THE ROLLER HINGE SETTING

• Stand with your legs on either side of the main shaft.
• Reach under each roller hinge with your index fingers. Use your thumbs to release the
locks over the roller hinges. (See Figure 10)
• Lift both sides of the table out of the A-frame at the same time. You may rest the table
on the crossbar of the A-frame.
• Unlock the cam locks for each roller hinge. Change the roller hinges to the desired
setting (A, B, or C, from most aggressive to least aggressive). (See Figure 11)
• Relock the cam locks. Replace the roller hinges into the hinge plates of the A-frame.

STORING THE INVERSION TABLE

• Loosen the de-rattler knob.
• Pull the height selector locking pin and slide the main shaft in all the way to the
ankle clamp assembly. Engage the pin in the storage setting.
• Rotate the table opposite from use until the table has turned 180 degrees and rests
against the cross bar on the A-frame.
• The legs of the A-frame base may then be folded together for compact storage.
(See Figure 12). WARNING: This operation may pinch fingers if not done
slowly and carefully.

TABLE MAT: REMOVING / CLEANING / TIGHTENING

• You may find it easier to remove the nylon mat while the table is in its storage position.
• Pull up on the plastic tension clips to loosen the adjustment straps.
• Release one corner at a time, then slide the mat off the frame.
• The mat should be washed in cold on gentle cycle. Replace the mat on the table
frame while still wet.
• If you feel the nylon mat needs to be tightened, pull the adjustment straps on the
back of the mat.
For additional languages in Spanish, French, Dutch, German, Italian or Portuguese, please contact customer service.
Classified as Medical
Equipment, part I in accordance
with UL 2601-1 and CAN/CSA
C22.2; General Requirements
for Safety in accordance with
Underwriters Laboratories, Inc.
* any modification to this device
will void the UL Classification
U.S. and foreign patents apply. Other foreign patents pending.
Teeter Hang Ups is a registered trademark of STL International, Inc.
®
and Inversion International, Ltd.
Specifications subject to change without notice.
© COPYRIGHT 2003, STL International, Inc.
International Law Prohibits Any Copying, 11/03-7
Assembly Instructions
Inversion Table.
®

MAINTENANCE

For information about the Teeter Hang Ups
assembling the equipment or questions about its use, please contact Customer Service at the
appropriate location below:
9902 162
Toll Free (Phone) 800-847-0143 (Fax) 800-847-0188
Local (Phone) 253-840-5252 (Fax) 253-840-5757
(email) Info26@TeeterHangUps.com (web) www.TeeterHangUps.com
PO Box: AP 59245, New Providence Island, Bahamas
(Phone) +1-242-362-1001 (Fax) +1-242-362-1002
(email) Info@InversionInternational.com (web) www.InversionInternational.com

STORAGE

Shows pin in
Setting C
5-year warranty, or if you have any problems
®
USA & Canada:
STL International, Inc.
nd
St. Ct. E., Puyallup, WA 98375
International:
Inversion International, Ltd.
Figure 10
A
B
C
Figure 11
Figure 12
#LF5100 Pg. 4