SAFETY INSTRUCTIONS SAFETY INSTRUCTIONS _VARNING: To reduce the risk of electric Llser-serviceable parts inside. The lightning head within a triangle is intended to tell the user that parts inside the product are a risk of electric shock to persons. Note To CATV System Installer: This reminder is provided to cali the CATV system installer's attention to article 820-40 of the National Electric Code that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical...
Page 4
EXAMPLE OF ANTENNA GROUNDING_AS PER NATIONAL ELECTRICAL CODE (NEC_._.._ ELECTRIC SERVICE If an outside antenna is connected to the decoder equipment, protection against voltage surges and built up static charges. NFPA 70, and in Canada Part 1 of the Canadian Electrical Code provides information with respect to proper grounding of the mast and supporting structure, grounding location of antenna-discharge unit, connection to grounding...
INFORMATION ON DIGITAL TEL E VISION Information on Digital Television Digital Television In April 1997, the Federal Communications 2006, all television required to continue broadcasting regular TV signals along side the digital signals until 2006. Cable and satellite TV are not affected by the FCC ruling. According to the FCC, digital broadcasting must be available in the top 30 markets, covering 50% of households, by the end of 1999.
Digital Picture Formats DTV supports eighteen (18) Advanced Television Systems Committee (ATSC)' display formats, which are variations of the four (4) following formats: 1080i (interlaced), 720p (progressive), 480p (progressive) and 480i (interlaced). The larger the number, the higher the resolution of the picture. Interlaced Scan For interlaced pictures, the odd number lines (picture information) are scanned, creating field 1, then the even number lines are scanned, creating field 2.
SDTV-Compatible SDTV-compatible TV models process and display standard definition output from the Panasonic STB as a 480p or 480i format. When DTV broadcasts are available in your viewing area, your SDTV monitor/receiver will be compatible display the incoming SDTV format.
Congratulations Your Panasonic digital set-top box (STB) features state-of-the-art technologyfor high-quality picture and sound with complete audio/video output jacks for your home theater system. D'TV signals are displayed in either an interlacedor progressive format, providinga clear, crisp picture. When connected to the STB, your HDTV-compatible monitor/receiver can display high-definition (HD'I'V) 1080i or 720p format and standard definition (SD'FV) 480p or 480i format.
IMPORTANT NOTES Important Notes STB Location This unit can be used available options. £3 Avoid excessive sunlight or bright lights. Keep away from excessive component failure. Fluorescent lighting may reduce Remote Control transmitting range. Connecting Cables Component video cables (Y, PB, PR) are provided for connection to a DTV-compatible monitor/receiver.
Cable IRC - Incremental Related Carrier Note: The Panasonic DTV set-top box is able to receive DTV signals from your local cable provider only if they are transmitted in the 8VSB modulation format approved by the FCC for DTV transmission.
NTSC Input Jack Input Jack NTSC Video and Audio Output Jacks Panasonic" NTSC iNPUT Digital Interface for Panasonic D-VHS Note: Refer to the Table of Contents for page numbers. Press to access and exit Panasonic Set-To DTV Video and Audio...
Channel Tuning Using Certain Some Panasonic television models* will automatically switch between using the STB or the TV to tune channels. When the remote control is in DTV mode and either the 0 ~ 9 numeric keypad or the Channel Up/Down (A or •...
FEATURES OF THE SET-TOP Channel Banner The Channel Banner is used by all tuning methods; DTV (Native, 1080i/480p and 480p) and TV (NTSC) mode to show you which channel and program you are currently viewing or selecting. your TV screen. Channel Banner DTV mode Channel displays...
Unavailable Channel Selection The unavailable channel. The following channel selection Tuning to a channel that is not transmitting any programs. Tuning to a channel that stopped broadcasting programs. The signal strength of the RF signal is insufficient to obtain consistent error free data. Found or Not Found The unavailable...
FEATURES OF THE SET-TOP BOX ATSC Display Formats The STB converts all eighteen (18) ATSC display formats available viewable programming. 1080i, 720p, 480p and 480i. resolutions and aspect ratios. Display Format Selection The STB allows you to choose a display format based on the capability of your TV or monitor.
480p If your TV is capable of displaying 480p format only, then set the OUTPUT MODE switch to 480p. NTSC Mode If your TV is capable of displaying NTSC format only, then set the OUTPUT MODE switch to NTSC. Note: When the mode switch is in the NTSC position, (component) and 480i (composite).
Page 17
FEATURES OF THE SET-TOP BOX Shrink Aspect The source aspect ratio will be maintained and the picture will shrink into full view on the screen. Sidebar Aspect 4:3 pictures will be viewed on a wide aspect TV screen with vertical bars on both sides of the picture.
Page 18
ASPECT RATIO FORMATS Source Signal FULL ZOOM These pictures show the different aspect ratios The 16:9 and 4:3 pictures available with a 16:9 monitor format. represent incoming The top picture source signals received format available by the STB. 16:9 source signal. The bottom pictures show the 16:9 monitor formats available 4:3 source signal.
The recorded data from the tape then needs to be decoded for playback through the STB. The STB provides everything necessary to use a Panasonic D-VHS VCR. The digital interface allows the STB to control the D-VHS VCR and can even turn it on and simultaneously start recording through the TIMER feature.
Getting Started Step 1. Connect AC Power Cord Plug the AC power cord into a grounded have finished making Step 2. Set-Top Box Connection Follow this diagram when connecting the STB to a DTV-compatible TV. DTV-COMPATIBLE Incoming signal from antenna or cable NOTE: AUDIO CABLES NOT INCLUDED...
Step 3a. Digital TV/Standard Follow this diagram if you have a DTV-compatible TV, no cable service and you want to receive digital channels through the STB and standard channels through the TV. An additional antenna may be required depending antenna can receive. NOTE: AND AUDIO CABLES NOT INCLUDED DTV-Compatible...
GETTING STARTED Step 3b. Digital TV/Standard Foltow this diagram if you have a conventional TV, no cable service and you want to receive digital channels through the STB and standard channels through the TV. An additional antenna may be required depending on which frequencies antenna can receive.
Step 3c. Digital TV/Cable Reception Follow this diagram receive digital (or through the TV if you have no cable box), Optional Cable Box NTSC INPUT DIGITALTV/CABLE Procedure Connect the antenna cable to the STB ATSC/DTV INPUT jack. If using a cable box, connect the cable wire from the wall jack to the cable box ANT (antenna) IN jack using a standard RF cable with a coaxial connector.
GETTING STARTED Step 3d. Digital TV/Cable Reception Follow this diagram if you have a conventional receive digital channels through the STB and cable channels through the cable box (or through the TV if you have no cable box. Optional Cable Box DIGITAL TV/CABLE RECEPTION Procedure...
Step 3e. Digital 8VSB Cable/Analog Follow this diagram if you have a DTV-compatible digital cable and you want to receive digital cable channels through the STB and analog cable channels through the cable box (or through the TV if you have no cable box).
GETTING STARTED Step 3f. Digital 8VSB Cable/Analog Follow this diagram if you have a conventional digital cable and you want to receive digital cable channels through the STB and analog cable channels through the cable box (or through the TV if you have no cable box).
Step 3g. NTSC Analog Cable Connection Follow this diagram Analog Signal ANALOG CABLE CONVENTIONAL Procedure • Connect the cable from the analog signal source to the NTSC input, Connect the Set Top Box NTSC video and left/right audio output to the Monitor video and left/right audio input.
Roller Guide Menu. SET UP Note: To exit the Roller Guide Menu, press the • MENU button. *Roller Guide Menu is a trademark of Panasonic Consumer Electronics Company. Patent Pending. TV models) r" ROLLER GUIDE MENU SELECTIONS...
Step 6a. ACTION / Navigation Press the ACTION button to select main menu items. highlight sub menus. to scroll through options within a feature. items. Note: Be careful to press ACTION in the middle of the button. middle of the button, the arrow buttons may be activated. Step 7.
GETTING STARTED Step 8. Programming Available MUST PERFORM MANUALLY ADDING TUNING SYSTEM EVERY AVAILABLE Automatic Channel The STB will scan for all available normally take several Procedure In SET UP Menu, select PROGRAM to choose AUTO to automatically scan and store all channels with a signal.
Connect digital interface cable from the digital interface output connection on the STB t the digital interface input connection on the D-VHS VCR. Note: The STB works with a Panasonic D-VHS VCR only. • If using a DTV-compatible STB to a DTV-compatible •...
INSTALLATION Set-Top Box Connection Follow this diagram Incoming signal from antenna or Procedure Move the output mode switch to the NTSC position. Connect video cable from the video output jack on the STB to the video input jack on the VCR.
Optional Connec_ons Set-Top Box Connection to Dolby Follow this diagram to connect the STB to a Dolby Digital AC-3 decoder, Incoming signal from antenna or cable NOTE: AC-3 DECODER AND DIGITAL AUDIO CABLE NOT INCLUDED DOLBY DIGITAL AC-3 DECODER SETUP Procedure Connect Digital Audio cable from the Digital Audio Out connection on the STB to the Digital Audio In connection on the Dolby Digital AC-3 decoder.
REMOTE CONTROL Remote Control ASPECT (Ratio) EUR511157 *To conserve batt_y _le, the LIGHT func_n can be disabled/er_bled by presszngR-TUNE and RECALL simultaneously.
REMOTE CONTROL FUNCTIONAL KEY CHART Remote Control Functional 1%"CBL DeS R-TUNE CD (AUX) AUX (Cassette Deck) RECALL TV VCR DV_LD €o (AUX) • ®® TY DTV VCR ®® c° (Au)9 @® Battery Installation Incorrect installation can cause battery leakage and corrosion that will damage the Remote Control Use two AA batteries: Remove the battery cover by pushing in near the arrow and sliding the cover...
SPECIAL REMOTE BUTTONS Special Remote Buttons ASPECT Aspect Ratio Selections The ASPECT button changes the aspect ratio (picture display shape) in response to the source signal and monitor format. You can also change the aspect ratio for your personal viewing preference. Each time the ASPECT button is pressed, the STB will cycle to the next available aspect ratio choice.
Page 40
ASPECT RATIO FORMATS Source Signal ZOOM These pictures show the different aspect ratios The 16:9 and 4:3 pictures available with a 16:9 monitor format. represent incoming The top picture shows the 16:g monitor source signals received format available when the STB receives a by the STB.
Page 41
SPECIAL REMOTE BUTTONS TV/VIOEO TV/Video The W/VIDEO VIDEO button is pressed, the TV will cycle through Channel, Video 1, Video 2, Video 3 and D'iV modes. Note: Not all television models will display all the modes. MENU Menu The MENU button allows you to access and exit the Roller Guide Menu. Each time the MENU button is pressed, the Roller Guide will appear on and disappear from the viewing screen.
Programming the Remote Control The Universal Remote Control can be programmed to operate many manufacturers' components using the component function buttons for VCR, DVD, AUX (RCVR, CD, TAPE, CASSETTE DECK and LD), CBL, D'I-V, TV, or DBS. Follow the procedures for programming your Remote Control with and without codes for the component.
The Universal Remote Control is capable of operating many component brands after entering a code. Some components may not operate because memory is limited• The Universal Remote Control does not control all features in all models. _entunen Oae_o Emerson 141 143 144 Rsher GE/Panasonic/ Quasar H_tachi Magnavox 210, 212 Marantz Archer 531 544...
ROLLER GUIDE MENU Roller Guide Menu Press the MENU button on the Remote Control to display the Roller Guide Menu, Press the • or • arrow to rotate the Roller Guide. Press the • Roller Guide Menu. SET UP Note: To exit the Roller Guide Menu, press the •...
Roller Guide Feature Chart Roller Guide Feature Chart SET UP " NPUT ;1/_} DISPLAY MONITOR ROLLER SET UP SOURCE - Select one of the following: • ANTENNA (default setting) - VHF/UHF • Cable - Standard Signals • Cable Harmonic Carrier Cable Incremental Carrier...
Page 49
ROLLER GUIDE FEATURE CHART Roller Guide Feature Chart (Cont.) BACKDROP INFO _,ONTROLS MINIMIZE TIMER BACKDROP Black (not recommended) Gray (default setting) INFO - Select ON or OFF for the Format Info Banner, D-VHS CONTROLS - Select to display D-VHS VCR Control Panel buttons and status box. MINIMIZE - Select to minimize D-VHS...
Special Features SET UP Antenna/Cable Select either Antenna are using. Cable must be 8VSB format for DTV reception. Procedure £] In SET UP Menu, select iNPUT. £3 Press the Ib arrow twice, then the • and • arrows to select ANTENNA, Cable STD, Cable HRC or Cable IRC.
SPECIAL FEATURES Channel Mapping Select ON for automatic channel mapping functions. The Channel Mapping feature allows the STB to match the actual DTV broadcast channel (assigned to your local TV station) to the channel number that the station uses to identify itself. For example, local channel 4 may actually be broadcasting digital programming on channel 60.
Programming Available Channels You must perform the automatic channel programming deleting channels because of the digital tuning system used by the STB. will ensure that every available channel will be captured and stored into memory. Automatic Channel Programming The STB will scan for all available normally take several minutes...
SPECIAL FEATURES Clock Set the time for the STB system clock. TIME will display on screen after pressing the POWER button, RECALL button, or when changing use the "Rmer feature). In SET UP Menu, select CLOCK to set the STB clock. Press the I_ arrow twice to move to the day field.
(Closed Captioned) The STB contains a built-in decoder that is capable of providing a visual display of the audio portion, The program viewed must provide Closed Captioning (CC) for the television to display it. CC is displayed in the form of text across the screen (white or colored letters on black background).
FEATURES D-VHS D-VHS VCR Control Panel The STB allows you to control a Panasonic D-VHS VCR through the digital interface. The on-screen panel of D-VHS VCR control buttons in the D-VHS menu lets you record and playback digital programs. Note: The STB mustbe on whenD-VHS VCR is recording.
Page 56
D-VHS VCR Status Messages The STB will report status information about the D-VHS VCR in the status box. The following table is a list of possible status messages. Command or Event STOP pLAY PAUSE _ D-vHs empty Play: Fast Forward Play: Fast Rewind Analog tape loaded D-VHS reported error...
SPECIAL FEATURES TIMER Timer I and Timer 2 The STB contains selected times, on selected channels STB to simultaneously Timer Set up In TIMER Menu, press the • and • arrows to select either TIMER 1 or TIMER 2. Note: TIME must be entered in CLOCK to operate TIMER features.
Page 58
The TIMER is active when the STB is OFF or ON. The STB wilr switch to the selected channel at the selected time set in the TIMER, Timer Error Messages The STB will scan the timer data fields and notify you of any problems before letting you set the Mode.
SPECIAL FEATURES NTSC TUNER OPERATIONS This STB has a separate NTSC tuner. The NTSC output can be displayed on a monitor with composite video inputs, Main Menu Press the NTSC button on the Remote control, Press the ACTION button on the remote control to display the MAIN MENU.
Page 60
MANUAL PROGRAM After programming all available channel, you can use the MANUAL PROGRAM feature to selectively add or delete channels. Procedure In MAIN MENU select MANUAL PROGRAM. Press the ACTION button on the remote control to display the menu features. £3 Use the •...
Page 61
SPECIAL FEATURES ANTENNA SOURCE Select TV or CABLE depending on the incoming signal source. Procedure _3 In MAIN MENU, selectANTENNA SOURCE. £3 Pressthe ACTION buttonon the remote controltodisplaythemenu features. £3 Pressthe • or • arrowto selectTV or CABLE. Pressthe ACTION buttontwiceto exit. CHANNEL CAPTION (LABEL) Program channel captions (station labels) for 30 stations using up to four characters.
Page 62
AUDIO SETUP Select STEREO, SAP or MONO, STEREO - For two channel audio reception. SAP - (Second Audio Program). Tunes to the alternate audio channel, if available (bilingual or descriptive audio). MONO - One channel audio. Use when stereo signal is weak. Procedure In MAIN MENU, select AUDIO SETUP.
TROUBLESHOOTING Troubleshooting Before requesting service for this unit, check the table below for a possible cause of the problem you are experiencing. Some simple checks or a minor adjustment on your part may eliminate the problem and restore proper operation. If you are in doubt about some of the check points, or if the remedies indicated in the table do not solve the problem, consult your dealer or call 1.888-VIEW-PTV No power...
Page 64
•Check that the AC power plug is securely plugged into the power outlet. .Check that equipment is connected properly. •Make sure it is a Panasonic D-VHS VCR. Make sure STB is on. •Check that the AC power plug is securely plugged into the power outlet.