Table of Contents
Advertisement
•
Extinguish all cigarettes, cigars, pipes, and other sources
of ignition.
•
Use only an approved fuel container.
•
Never remove fuel cap or add fuel with the engine
running.
•
Allow engine to cool before refueling.
•
Never refuel the machine indoors.
•
Never store the machine or fuel container where there is
an open flame, spark, or pilot light such as on a water
heater or on other appliances.
•
Never fill containers inside a vehicle or on a truck or
trailer bed with a plastic liner. Always place containers on
the ground away from your vehicle before filling.
•
Remove equipment from the truck or trailer and refuel it
on the ground. If this is not possible, then refuel such
equipment with a portable container, rather than from a
fuel dispenser nozzle.
•
Keep the nozzle in contact with the rim of the fuel tank
or container opening at all times until fueling is complete.
Do not use a nozzle lock open device.
•
If fuel is spilled on clothing, change clothing immediately.
•
Never overfill fuel tank. Replace fuel cap and tighten
securely.
Operation
•
Never run an engine in an enclosed area.
•
Only operate in good light, keeping away from holes and
hidden hazards.
•
Be sure all drives are in neutral and parking brake is
engaged before starting the engine. Only start the engine
from the operator's position. Use seat belts if provided.
•
Slow down and use extra care on hillsides. Be sure to
travel in the recommended direction on hillsides. Turf
conditions can affect the machine's stability. Use caution
while operating near drop-offs.
•
Slow down and use caution when making turns and when
changing directions on slopes.
•
Never raise the deck with the blades running.
•
Never operate with guards not securely in place. Be
sure all interlocks are attached, adjusted properly, and
functioning properly.
•
Do not change the engine governor setting or overspeed
the engine.
•
Stop on level ground, lower the cutting units, disengage
drives, engage parking brake (if provided), shut off engine
before leaving the operator's position for any reason.
•
Stop equipment and inspect the blades after striking
objects or if an abnormal vibration occurs. Make
necessary repairs before resuming operations.
•
Keep hands and feet away from the cutting units.
•
Look behind and down before backing up to be sure of
a clear path.
•
Never carry passengers and keep pets and bystanders
away.
•
Slow down and use caution when making turns and
crossing roads and sidewalks. Stop blades if not mowing.
•
Do not operate the mower under the influence of alcohol
or drugs.
•
Lightning can cause severe injury or death. If lightning
is seen or thunder is heard in the area, do not operate
the machine; seek shelter.
•
Use care when loading or unloading the machine into a
trailer or truck.
•
Use care when approaching blind corners, shrubs, trees,
or other objects that may obscure vision.
•
The operator shall turn on flashing warning lights, if
provided, whenever traveling on a public road, except
where such use is prohibited by law.
Maintenance and Storage
•
Disengage drives, lower the cutting units, move traction
pedal to Neutral, set parking brake, stop engine and
remove key. Wait for all movement to stop before
adjusting, cleaning or repairing.
•
Clean grass and debris from cutting units, drives, muffler.
Let engine cool before storing and do not store near
flames, and engine to help prevent fires. Clean up oil or
fuel spillage.
•
Let engine cool before storing and do not store near
flame.
•
Shut off fuel while storing or transporting. Do not store
fuel near flames or drain indoors.
•
Park machine on level ground. Never allow untrained
personnel to service machine.
•
Use jack stands to support components when required.
•
Carefully release pressure from components with stored
energy.
•
Disconnect battery before making any repairs. Disconnect
the negative terminal first and the positive last. Reconnect
positive first and negative last.
•
Use care when checking blades. Wrap the blades or
wear gloves, and use caution when servicing them. Only
replace blades. Never straighten or weld them.
•
Keep hands and feet away from moving parts. If possible,
do not make adjustments with the engine running.
•
Charge batteries in an open well ventilated area, away
from spark and flames. Unplug charger before connecting
or disconnecting from battery. Wear protective clothing
and use insulated tools.
•
Keep all parts in good working condition and all hardware
tightened. Replace all worn or damaged decals.
Hauling
•
Use care when loading or unloading the machine into a
trailer or truck.
4
Advertisement
Table of Contents
