Table of Contents
Advertisement
Preparation
•
Thoroughly inspect the area where the appliance is to be
used and remove all doormats, sleds, boards, wires, and
other foreign objects.
•
Do not operate the appliance without wearing adequate winter
garments. Avoid loose fitting clothing that can get caught in
moving parts. Wear footwear that will improve footing on
slippery surfaces.
•
Do not attempt to clear snow from a gravel or crushed rock
surface. This appliance is intended for use only on paved
surfaces.
•
Never attempt to make any adjustments while the motor
is running (except when specifically recommended by
manufacturer).
•
Always wear safety glasses or eye shields during operation or
while performing an adjustment or repair to protect eyes from
foreign objects that may be thrown from the appliance.
Operation
•
Do not put hands or feet near or under rotating parts. Keep
clear of the discharge opening at all times.
•
Exercise extreme caution when operating on or crossing
gravel drives, walks, or roads. Stay alert for hidden hazards
or traffic.
•
After striking a foreign object, stop the motor, unplug the
extension cord, remove the key, and thoroughly inspect
the appliance for any damage. Repair any damage before
starting and operating the appliance.
•
If the appliance should start to vibrate abnormally, stop the
motor and check immediately for the cause. Vibration is
generally a warning of trouble.
•
Stop the motor, remove the key, and unplug the appliance
whenever you leave the operating position, before unclogging
the rotor blade housing or discharge chute, and when making
any repairs, adjustments, inspections, and while transporting
the machine.
•
Do not direct the snow discharge at any bystanders.
•
Do not operate with anyone standing in front of the machine.
•
When cleaning, repairing, or inspecting the appliance, stop
the motor, remove the key, unplug the appliance, and ensure
that the rotor blades and all moving parts have stopped.
•
Exercise extreme caution when operating on slopes.
•
Do not operate the machine at high transport speed on
slippery surfaces.
•
Use care when reversing the machine.
•
Never operate the appliance without proper guards and other
safety protective devices in place and working.
•
Never direct the discharge toward people or areas where
property damage can occur. Keep children and others away.
•
Do not overload the capacity of the appliance by attempting to
clear snow at too fast a rate.
•
Look behind and use care when backing up with the
appliance.
•
Never operate the appliance without good visibility or light.
Always be sure of your footing, and keep a firm hold on the
handle. Walk; never run.
•
Disengage power to the impeller when the machine is being
transported or not in use.
•
Only use Toro-approved attachments and accessories.
Clearing a Clogged Discharge
Chute
Hand contact with the rotating rotor blades inside the discharge
chute is the most common cause of injury associated with
snowthrowers. Never use your hand to clean out the discharge
chute.
To clear the chute:
•
Shut the motor off, remove the key, and unplug the
extension cord from the machine!
•
Wait 10 seconds to be sure the rotor blades have stopped
rotating.
•
Always use a clean-out tool, not your hands.
Maintenance and Storage
•
Before each use check all fasteners for proper tightness to
ensure that the appliance is in safe working condition.
•
Always refer to the Operator's Manual for important details if
the appliance is to be stored for an extended period.
•
Maintain or replace safety and instruction labels as needed.
•
Run the appliance for a few minutes after throwing snow to
prevent freeze-up of the rotor blades.
SAVE THESE INSTRUCTIONS
Sound Pressure
This unit has a maximum sound pressure level at the operator's
ear of 83 dBA, based on measurements of identical machines
per EN 11201.
Sound Power
This unit has a guaranteed sound power level of 98 dBA, based
on measurements of identical machines per EN 3744.
Vibration
This unit does not exceed a hand/arm vibration level of 1.2 m/s2,
based on measurements of identical machines per EN 1033.
2
Advertisement
Table of Contents
